Generic
-
0.56inch 0-100V Three Wire LED Display Digital DC Voltmeter-BLUE
SKU: 309478₹ 230.00(inc GST)
₹ 194.92 (+18% GST extra)
- Operating Voltage: 0-100 VDC
- It is a 3-wire display.
- LED Color: Blue
- Current Consumption : <40 mA.
- Accuracy: 0.1 V.
- Refresh Speed : Approx 200mS/time.
- The display on Voltage: 3 V.(but not measure accurately up to 3.6V).
-
0.56inch 0-100V Three Wire LED Display Digital DC Voltmeter-Green
SKU: 309466₹ 230.00(inc GST)
₹ 194.92 (+18% GST extra)
- Operating Voltage: 0-100 VDC
- It is a 3-wire display.
- LED Color: Green
- Current Consumption : <40 mA
- Accuracy: 0.1 V.
- Refresh Speed : Approx 200mS/time.
- The display on Voltage: 3 V.(but not measure accurately up to 3.6V).
-
0.56inch 0-100V Three Wire LED Display Digital DC Voltmeter-RED
SKU: 309337₹ 230.00(inc GST)
₹ 194.92 (+18% GST extra)
- Operating Voltage: 0-100 VDC
- It is a 3-wire display.
- LED Color: RED
- Current Consumption : <40 mA
- Accuracy: 0.1 V.
- Refresh Speed : Approx 200mS/time.
- The display on Voltage: 3 V.(but not measure accurately up to 3.6V).
-
1 Channel 5V 10A Relay Module For Arduino PIC AVR DSP ARM
SKU: 9716₹ 79(inc GST)
₹ 66.95 (+18% GST extra)
- Max Current : 20mA
- Relay Contact Current Capacity at AC250V: 10A
- Relay Contact Current Capacity at DC30: 10A
- One normally closed contact and one normally open contact
- One normally closed contact and one normally open contact
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator lamp
-
1.5 meter RJ45 Retractable Travel Network Cable
SKU: 212296₹ 79.00(inc GST)
₹ 66.95 (+18% GST extra)
- New generic Retractable Ethernet Cable, CAT5E, Clear
- The cable connects all the hardware destinations on a Local Area Network.
- Ideal for use with 10/100/1000BaseT networks.
- This 5-foot patch cable features 50-micron gold plated connectors that ensure a clean and clear transmission.
- The RJ-45 tap from being damaged during installation.
- Easy to carry in travel bag
-
1.5mm Electrical Waterproof Seal Heat Shrink Splice Wire Sleeve White 5pcs
SKU: 471362₹ 99.00(inc GST)
₹ 83.9 (+18% GST extra)
- Shrinkage ratio: 2:1.
- Tubing: Polyolefin.
- Operating temperature : -55℃ ~ 125℃.
- Minimum shrink temperature: 80℃.
- Starting temperature of solder melt: 138℃.
- Minimum full recovery temperature: 160℃.
-
1.5V 1.8V 2.5V 3V 3.3V 3.7V 4.2V to 5V DC-DC DC Boost Converter Module Step Up Board
SKU: 406344₹ 149.00(inc GST)
₹ 126.27 (+18% GST extra)
- Input voltage 0.8-3.3V output voltage 3.3V
- Maximum output current: 500 mA
- Starting voltage 0.8V, output current 10MA
- Input more than 3 v, and have spent 5V output of 400-400 MA
- Operating frequency: 150KHZ
- Typical conversion efficiency: 85%
-
1.5W 6V 250mA Solar Panel (12x11CM)
SKU: 203903₹ 349.00(inc GST)
₹ 295.76 (+18% GST extra)
- 100% new high quality.
- 6 volt 1.5-watt polycrystalline solar panel USB charging
- High conversion speed, high-efficiency output.
- Excellent low light effect.
- High transmittance tempered glass.
- A unique technique to prevent water frozen within the deforming framework.
-
1/4 Cmos 640X480 USB Camera with Collapsible Cable for Raspberry Pi
SKU: 216740₹ 299.00(inc GST)
₹ 253.39 (+18% GST extra)
- Supports 300k pixels, a maximum resolution of 640×480, and VGA/ YUY2 packed formats
- Dimension: 40mm × 15mm × 30mm; designed for Raspberry Pi and PC
- With a retractable USB cable, convenient to store
- Applies USB 2.0 High-speed Sensor, plug-and-play, no driver installation
- High definition and true colour images.
-
1000mm Trapezoidal 4 Start Lead Screw 10mm Thread 2mm Pitch Lead Screw with Copper Nut
SKU: 501487₹ 1,199.00(inc GST)
₹ 1016.1 (+18% GST extra)
- Lead Screw Material: 304 Stainless Steel.
- Length: 1000mm.
- Diameter: 10 mm.
- 4 Start Lead Screw
- Brass Nut Size: 12 x 13 x 22 mm.
- Mainly use for Stepping motor driving guide rail.
- T shape design, made of high-quality stainless steel material.
- Easy to install and convenient to use.
-
100Pcs. 1/4W Metal Film Resistors Assortment for DIY Electronic Projects and Experiments
SKU: 312321₹ 99.00(inc GST)
₹ 83.9 (+18% GST extra)
- 1/4W 1% Tolerance Metal Film Resistors so 5 color bands, This is a great assortment for front ends and low power applications.
- These resistors are typical axial-lead metal film resistors, which have much better temperature stability than their carbon equivalents,
- Lower noise and are generally better for high frequency or radio frequency applications.
- Each bundle is labeled with the resistance value and packaged in Strip which easy to tear which make your work easier
-
10A DC-DC Step-down Adjustable Constant Voltage Module
SKU: 405535₹ 369.00(inc GST)
₹ 312.71 (+18% GST extra)
Applications:
1. High-power LED driver.
2. Lithium battery(or lead accumulator) charge.
3. Vehicle-mounted power supply.
4. Low voltage system power supply.
5. 6V, 12V, 14V, 24V battery charge.
6. On-board laptop power supply.
7. regulated power supply.
8.Low voltage power supply system -
1240 12V DC 0.6A 7.5W Solenoid for Electric Door Lock
SKU: 312517₹ 523.00(inc GST)
₹ 443.22 (+18% GST extra)
- Holding force: 0.25kg
- Energized forms: intermittent
- Unlocking time: 1S
- Dimensions: 54 x 42 x 28 mm (LxWxH)
- High quality ultra-compact electric lock.
- Rustproof, durable, safe, convenient to use.
- Suction which tightly sucks the iron, thus locking the door.
- Applicable for being installed in the escape door or fire door electronic controlled system.
-
1240 24V DC 0.8A 7.5W Solenoid for Electric Door Lock
SKU: 312543₹ 523.00(inc GST)
₹ 443.22 (+18% GST extra)
- Holding force: 0.25kg
- Energized forms: intermittent
- Unlocking time: 1S
- Dimensions: 54 x 42 x 28 mm (LxWxH)
- High quality ultra-compact electric lock.
- Rustproof, durable, safe, convenient to use.
- Suction which tightly sucks the iron, thus locking the door.
- Applicable for being installed in the escape door or fire door electronic controlled system.
-
1240-12V DC 12V 1.7A 20.6W 1kg Holding Solenoid for Electric Door Lock
SKU: 313009₹ 1,004.00(inc GST)
₹ 850.85 (+18% GST extra)
- Iron Body Material
- High quality ultra-compact electric lock.
- Rustproof, durable, safe, convenient to use.
- Suction which tightly sucks the iron, thus locking the door.
- Designed with the open frame type and mount board, high power.
- Easy to install for the electric door lock or other automatic door lock systems with the mounting board
- Applicable for being installed in the escape door or fire door electronic controlled system.
-
125KHz RFID Card – 5pcs
SKU: 31353₹ 89.00(inc GST)
₹ 75.42 (+18% GST extra)
- Contactless transmission of data and supply energy (no battery needed)
- Operating distance: Up to 1 Meter (depending on antenna geometry)
- Operating frequency: 125KHz
- Data transfer: 106 kbit/s
- Data integrity: 16 Bit CRC, parity, bit coding bit counting
- Anticollision
-
13.56MHz ER300D Plug and Play RFID Reader
SKU: 232585₹ 1,575.00(inc GST)
₹ 1334.75 (+18% GST extra)
- No Programming Required
- No Drivers Software need to Install
- Just Plug and Play
- Very low power required to operate
- Can Run even on mobile Phone Power
- Can detect UID cloned card
- Contactless USB smart card reader
-
1S 18650 3.7V lithium battery protection plate 6 MOS
SKU: 44100₹ 99.00(inc GST)
₹ 83.9 (+18% GST extra)
- Over charge detection voltage : 4.25 + 0.05V
- Over charge release voltage : 4.23 + 0.05V
- discharge detection voltage : 2.45 + 0.1V
- Ceiling continuous current : 12A
- Overcurrent detection current : 15A
- Input Charging voltage : 4.2V
- Product size : 35*7.4*2.2MM
- IC components : DW01+8205A
-
1W 5V 200mA Solar Panel ( 11 x 9.2CM )
SKU: 203902₹ 269.00(inc GST)
₹ 227.97 (+18% GST extra)
- 100% new high quality.
- 5 volt 1-watt polycrystalline solar panel USB charging
- High conversion speed, high-efficiency output.
- Excellent low light effect.
- High transmittance tempered glass.
- A unique technique to prevent water frozen within the deforming framework.
-
1W 6V 167mA Solar Panel (11×9.2CM )
SKU: 203904₹ 269.00(inc GST)
₹ 227.97 (+18% GST extra)
- 100% new high quality.
- 6 volt 1-watt polycrystalline solar panel USB charging
- High conversion speed, high-efficiency output.
- Excellent low light effect.
- High transmittance tempered glass.
- A unique technique to prevent water frozen within the deforming framework.
-
1×40 Berg Strip Male Connector – 5pcs
SKU: 470829₹ 69.00(inc GST)
₹ 58.47 (+18% GST extra)
- Number of Pins: 40
- Pin Spacing(pitch): 2.54 mm
- Length of the Strip: 103 mm
- Pin height: 6 mm
- Square Posts.
- Stackable – End to End and Side to side.
- Can be manually broken for the length needed.
- Standoffs allow cleaning of solder contaminants.
-
2-IN-1 Raspberry Pi Dual TF / SD Card Switcher Adapter
SKU: 210649₹ 799.00(inc GST)
₹ 677.12 (+18% GST extra)
This 2-IN-1 Raspberry Pi Dual TF / SD Card Switcher Adapter is a micro SD card switcher, specially designed for the Raspberry Pi to serve the purpose. You can now enjoy the convenience of using two micro SD cards at the same time on the same Pi!
-
2.4GHz NRF24L01+PA+LNA SMA Wireless Transceiver Antenna
SKU: 18826₹ 249.00(inc GST)
₹ 211.02 (+18% GST extra)
- Voltage: 3-3.6V (recommended 3.3V) V.
- Maximum output power: +20dBm.
- Power-down mode current: 4.2uA.
- Operating Range: 1Km
- Antenna Gain (peak): 2Dbi.
- 2MB rate (Open area): 520m.
- 1MB rate (Open area): 750m.
- 250Kb rate (Open area): 1100m.
- It uses 2.4GHz global open ISM band, with license free.
- SPI interface facilitates the communication with MCU I/O port.
-
220 x 220 x 0.5 mm 3D Printer Hot Bed Tape Sticker Build Plate Tape
SKU: 392199₹ 215.00(inc GST)
₹ 182.2 (+18% GST extra)
- Material: Nylon+ABS+PLA+HIPS+PETG+PC+RETT+TPE consumptive material
- Easily stick on the heat bed platform.
- One tape can be used repeatedly for at least 3 months normally.
- Build sheet adheres to a print bed to help the filament stick during printing, it is easy to take off the models.
- Compatible with ABS, PLA, HIPS as well as other kinds of filament.
-
250W High Power Constant voltage Current Adjustable Aluminum Substrate LED Driver Module
SKU: 405563₹ 449.00(inc GST)
₹ 380.51 (+18% GST extra)
- DIY a stabilized power supply, input 12V is ok, the output can be adjustable in the range of 12~50V.
- Offer power for your electronic equipment, you can set the output voltage value according to your system voltage.
- As the car power supply offer power for your laptop, PDA or a variety of digital products.
- A high-power notebook mobile power DIY: coupled with a large-capacity 12V lithium battery pack
- Solar panel voltage regulator.
- Charge for the storage battery, lithium battery etc.
- Drive high-power LED lights.
-
2S-6S Lipo Battery USB Converter T Plug Cellphone Charger Adapter
SKU: 127285₹ 449.00(inc GST)
₹ 380.51 (+18% GST extra)
- Input: 6 to 26VDC (2S-6S LiPo Batteries)
- Output: 5V-2A DC
- Input Connector Type: T plug Male
- Output Interface: USB
- 7 Segment LED Display to monitor battery Voltage
- Anti-slip plug, good contact performance
- Precision display by TW programmed MCU
-
3 Pin NTC Thermistor Temperature Sensor Module
SKU: 365937₹ 59.00(inc GST)
₹ 50 (+18% GST extra)
- Adopt the NTC thermistor sensor, sensitivity is good
- The comparator output, signal clean, good waveform, driving ability is strong, for more than 15 ma.
- With potentiometer to adjust the temperature detection threshold
- Working voltage: 3.3 V to 5 V
- Output form: digital switch output (0 and 1)
- It has a fixed bolt hole, convenient installation
-
3 Series 40A 18650 Lithium Battery Protection Board 11.1V 12.6V with Balance for Drill Motor Lipo Cell Module
SKU: 223554₹ 298.00(inc GST)
₹ 252.54 (+18% GST extra)
- 3S 11.1V 12.6V 40A 18650 lithium battery protection board (comes with recovery function-AUTO Recovery)
- Application: Nominal voltage of 3.6V, 3.7V lithium battery (including 18650.26650, a polymer lithium battery)
- Continuous discharge current (upper limit): 40A (if the cooling environment is not good, please reduce the load current use)
- Continuous charge current (upper limit): 20A
-
3.3V Adapter Board for 24L01 Wireless Module
SKU: 395873₹ 49.00(inc GST)
₹ 41.53 (+18% GST extra)
- It can be used with NRF24L01 wireless module
- Add core nRF24L01+ Breakout Adapter with onboard 3.3V Regulator
- Onboard 3.3V voltage regulator accepts your Arduino +5V supply and provides 3.3V for the attached nRF24L01+ module
- Allows for easy connection to nRF24L01+ modules
- Small power on SMD LED indicator
-
30W Pixel OV7670 Camera Module with High Quality Connector
SKU: 421571₹ 399.00(inc GST)
₹ 338.14 (+18% GST extra)
- Operating voltage:2.5 to 3.0V.
- Pixel Resolution: 300000 pixels (3MP)
- Dark Current: 12 mV/s at 60;
- Active power:60mW/15fps VGA;
- Optical Size:1.6 inch;
- Angel of view:67 degrees
- Maximum Frame Rate:30fps VGA;
- Sleep Power consumption: <20μA
- Temperature operation: -30 ° C to 70 ° C
- Stable operation: 0 ° C to 50 ° C
- Maximum conversion rate: 30fps VGA
- Sensitivity: 1.3V/(Lux-sec)
- Pixel area: 3.6 μm x 3.6 μm
- Dark current: 12 mV/s at 60 °C
- Signal to noise ratio: 46 dB
- Dynamic range: 52 dB
-
31 in 1 Universal Multifunction Portable Screwdriver Set
SKU: 305777₹ 99.00(inc GST)
₹ 83.9 (+18% GST extra)
- Compact and Portable pocket toolkit
- 30 different head style
- Rubber Shockproof gripped handle
- Strong and durable plastic Case
- Colour: Yellow-Red
- Interchangeable Precise Manual Tool Kit.
- High Strength Chrome Alloy is used to manufacture this tool.
- Magnetic bits are easy to fit into the handle.
- Heat resistant.
-
3mm Electrical Waterproof Seal Heat Shrink Splice Wire Sleeve White-Red 5pcs
SKU: 470836₹ 99.00(inc GST)
₹ 83.9 (+18% GST extra)
- Shrinkage ratio: 2:1.
- Tubing: Polyolefin.
- Operating temperature : -55℃ ~ 125℃.
- Minimum shrink temperature: 80℃.
- Starting temperature of solder melt: 138℃.
- Minimum full recovery temperature: 160℃.
-
3V-5V RFID YHY502CG Reader Writer Module UART Interface
SKU: 232584₹ 1,160.00(inc GST)
₹ 983.05 (+18% GST extra)
This HY502 series of RFID reader/writer modules are based on non-contact card reader ASCI chip compatible with ISO14443 standard. It uses 600nm CMOS EEPROM technology, supports ISO14443 type A protocol, and also supports the MIFARE standard encryption algorithm.
-
4 Channel Wireless Four Button Remote Control Transmitter Receiver Module (Mode: Non Locking)
SKU: 28460₹ 290.00(inc GST)
₹ 245.76 (+18% GST extra)
- No. of channel: 4
- Operating mode: Non-Locking
- Receiver Operating voltage: DC 5V.
- Receiver sensitivity is: -98dB.
- Transmitter Operating voltage: DC 12V
- Transmitting frequency: 315 MHZ.
- Transmitter Operating current: 10mA at 12V.
- TransmitterRadiated power: 10mW at 12V.
- Transmission distance: 5M to 10M
-
4 Series 30A 18650 Lithium Battery Protection Board 14.8V 16V with Cable
SKU: 223550₹ 298.00(inc GST)
₹ 252.54 (+18% GST extra)
4 Series 30A 18650 Lithium Battery Protection Board 14.8V 16V with Cable, a Balance Board for Drill Motor Lipo Cell Module comes with recovery function-AUTO Recovery and Integrated 10 low load resistance MOS tube.
-
4 Series 40A 18650 Lithium Battery Protection Board 14.8V 16.8V with Balance for Drill Motor Lipo Cell Module
SKU: 223535₹ 345.00(inc GST)
₹ 292.37 (+18% GST extra)
- The Successful start of the drill requires three 15C-20C power battery, or six 10C-15C power battery (ordinary 18650 cannot start the drill!!)
- Strictly according to map wiring 0V, 4.2V, 8.4V, 12.6V, 16.8V, do not deliberately short circuit.
