SmartElex
Showing all 35 results
-
-
Raspberry Pi Hats
SmartElex 10D DC Motor Driver HAT for Raspberry Pi
SKU: 128421- Wide 6V to 28V motor Operating Voltage.
- Continuous 10A maximum current without Heatsink and 30A peak current for 10 Seconds.
- Two brushed DC motor Bidirectional control.
- Current limiting at 35A.
- PWM frequency up to 32KHz
- Support TTL PWM from the microcontroller
- Internal thermal shutdown
- Under-voltage lockout
- PWM and direction controlled driving of four externally powered NMOS transistors
- 3V and 5V logic level input.
SKU: 128421 -
Brushed / Brushless DC motor Driver
SmartElex 10D Motor Driver for Arduino UNO
SKU: 198176- Onboard 5V 3A Buck Converter.
- Continuous 10A maximum current without Heatsink and 30A peak current for 10
- Two brushed DC motor Bidirectional control.
- Current limiting at 35A.
- PWM and direction controlled driving of four externally powered NMOS transistors
SKU: 198176 -
Brushed / Brushless DC motor Driver
SmartElex 10S DC Motor Driver HAT
SKU: 103711- Wide 6V to 28V motor Operating Voltage.
- One brushed DC motor Bidirectional control.
- Current limiting at 35A.
- PWM frequency up to 32KHz
- Support TTL PWM from the microcontroller
- Internal thermal shutdown
- Under-voltage lockout
SKU: 103711 -
-
Brushed / Brushless DC motor Driver
SmartElex 15D Smart Motor Driver
SKU: 199307- Support motor voltage from 7V to 28V.
- Onboard Low, Internal resistance MOSFETs are switched at 16 KHz frequency.
- Overcurrent and Thermal protection.
- Multiple input modes: RC, Analog, PWM, Serial Packetized.
- On board push buttons for test and manual operation.
SKU: 199307 -
-
Brushed / Brushless DC motor Driver
SmartElex 30D Dual Channel 30A Smart DC Motor Driver
SKU: 77719- Supplying 30 amps continuous with peak currents up to 85 amps (2 Sec) per channel.
- Support motor voltage from 7V to 30V.
- Onboard Low Internal resistance MOSFETs are switched at 16 KHz frequency.
- Overcurrent protection and indication.
- Thermal protection.
- Multiple input modes: RC, Analog, PWM, Serial Packetized.
- On board push buttons for test and manual operation.
SKU: 77719 -
8051 Board
SmartElex Aryabhatta 8051 Microcontroller Development Board AT89S52 with Onboard USB Programmer
8051 BoardSmartElex Aryabhatta 8051 Microcontroller Development Board AT89S52 with Onboard USB Programmer
SKU: 28279- Quartz crystal 11.0592 MHz
- On board programmer.
- Reset button.
- Power plug-in jack.
- External pull-up resistors for Port 0.
- Port extensions for all ports.1.
- Good start for beginners.
- Easy to use.
SKU: 28279 -
8051 Board
SmartElex AT89S52 Development Board with LCD
SKU: 464732Â
- Onboard 5V regulator (78M05) circuit.
- On-Board power supply on-off switch
- On-Board DC motor Driver L298P
- On-Board 4×4 Matrix Keypad.
- On-Board 4 bit 16×2 LCD Display.
- 0592MHz crystal.
- Port extensions for all ports with detailed pin labelling for easy identification of pins
- Onboard USB TO Serial – CH340 Chip.
- On-board Micro USB USBASP for loading HEX file.
SKU: 464732 -
8051 Board
SmartElex AT89S52 Development Board.
SKU: 451834- Onboard 5V regulator (78M05) circuit.
- On-Board power supply on-off switch
- On-Board DC motor Driver L298P
- On-Board 4×4 Matrix Keypad.
- On-Board 4 bit 16×2 LCD Display.
- 0592MHz crystal.
- Port extensions for all ports with detailed pin labelling for easy identification of pins
- Onboard USB TO Serial – CH340 Chip.
- On-board Micro USB USBASP for loading HEX file.
SKU: 451834 -
AVR Development Board
SmartElex ATmega2560 Development Board
SKU: 245283- Microcontroller: ATMEGA2560 with 16 MHz crystal with On-Board USBASP Programmer.
- Power: 7 to 15 VDC with Reverse Polarity Protection.
- 2.4GHz ZigBee (XBee) wireless module adaptor
- 2×16 Character Alphanumeric LCD.
- SD card Holder.
- CH340G USB to Serial converter.
- ESP8255 Adaptor interface with USB to Serial Converter.
SKU: 245283 -
AVR Development Board
SmartElex ATmega2560 Development Board with LCD1602 LCD Display-Upgraded
SKU: 631968- Microcontroller: ATMEGA2560 with 16 MHz crystal with On-Board USBASP Programmer.
- Power: 7 to 15 VDC with Reverse Polarity Protection.
- 2.4GHz ZigBee (XBee) wireless module adaptor
- 2×16 Character Alphanumeric LCD.
- SD card Holder.
- CH340G USB to Serial converter.
- ESP8255 Adaptor interface with USB to Serial Converter.
SKU: 631968 -
AVR Development Board
SmartElex ATmega32 Development Board on-board Programmer
SKU: 80650- Onboard 5V regulator (78M05) circuit.
- On-Board power supply on-off switch
- Power Status LED (RED)
- User LED D0, D1 connected to any port pin through D0, D1 Jumper respectively.
- User Switch SW1, SW2 connected to any port pin through SW1, SW2 Jumper respectively.
- Onboard 12 MHz crystal
- Port extensions for all ports with detailed pin labeling for easy identification of pins
- Onboard USB TO Serial – CH340 Chip.
- On-board Micro USB USBASP for loading HEX file.
- Servo motor Connector (Run only up to 300mA).
SKU: 80650 -
Relay Switch Modules
SmartElex Battle Relay
SKU: 55640- Switching Voltage: [email protected]; [email protected]
- Trigger Voltage: 5VDC
- Relay resistance: 100 mΩ max
- 4.8V to 5.2V operating voltage
- 30mA typical draw from receiver
- Powerful auxiliary weapons control in RC combat.
- Glow plugs control in RC nitro vehicles.
SKU: 55640 -
Relay Switch Modules
SmartElex Dual Channel Battle Relay
SKU: 74971- Trigger Voltage: 5VDC
- Switching Voltage: [email protected]; [email protected]
- Relay resistance: 100 mΩ max
- Module operating voltage:Â 4.8V to 5.2V
- 40mA typical draw from the receiver
- Powerful auxiliary weapons control in RC combat.
- Glow plugs control in RC nitro vehicles.
SKU: 74971 -
Shield for Arduino
SmartElex GPS Data Logger Shield for Arduino
SKU: 139462- The multi-GNSS engine for GPS, GLONASS, Galileo, and QZSS.
- Embedded patch antenna.
- Automatic antenna switching function.
- High sensitivity: -167dBm @Tracking, -149dBm @Acquisition
- 99 acquisition channels, 33 tracking channels
- Balloon mode, for high altitude up to 80km
- Support DGPS, SBAS (WAAS/EGNOS/MSAS/GAGAN)
- Great anti-jamming performance due to multi-tone active interference canceller
- Support SDK command developed by Quectel
SKU: 139462 -
Raspberry Pi Hats
SmartElex GPS HAT for Raspberry Pi
SKU: 124975- High Tracking and Acquisition sensitivity
- The multi-GNSS engine for GPS, GLONASS, Galileo, and QZSS
- 99 acquisition channels, 33 tracking channels.
- Balloon mode, for high altitude up to 80km.
- PPS VS. NMEA can be used for time service.
- Support SDK command developed by Quectel.
- Automatic antenna switching function.
- Built-in Real Time Clock (RTC)
- PPS output on a fix.
- Internal patch antenna
- Fix status LED blinks to let you know when the GPS has determined the current coordinates.
- Great anti-jamming performance
Â
SKU: 124975 -
GSM / GPRS Modules, Raspberry Pi Hats
SmartElex GSM HAT for Raspberry Pi
SKU: 132520- Based on the Quectel M66 Module
- Send/Receive SMS
- Make/Receive voice call with 3.5mm audio jack.
- Quad-band module (850/ 900/ 1800/ 1900MHz).
- Include Onboard Bluetooth BT 3.0 with an antenna.
- Controlled via AT commands.
- Compatible with all Raspberry Pi Version
- Autobauding 4800bps to 115200bps.
SKU: 132520 -
-
Raspberry Pi Hats
SmartElex GSM/GPRS/GNSS Bluetooth HAT for Raspberry Pi
SKU: 195380- Quad-band full-featured GSM/GPRS (850/ 900/ 1800/ 1900MHz).
- GNSS receiver channels: 99 acquisition/ 33 tracking channels
- Include Onboard Bluetooth BT 3.0 with an antenna.
- Controlled via AT commands.
- Autobauding 4800bps to 115200bps.
- Maximum download speed 85.6kbps.
SKU: 195380 -
Interface Module
SmartElex IOIO OTG for Android
SKU: 86932- Recommended Input Voltage: 12V
- Input Voltage Range: 5-15V
- 2 Pin 2mm SMD JST Right-angle Connector for Input supply
- On-board TPS62133RGTT Synchronous step down DC-DC converter.
- Power Status LED (RED)
- Micro USB for Communication with Android.
- One start LED connected to boot pin (RC12 =Pin no. 39).
- User Switch SW1, SW2 connected to any port pin through SW1, SW2 Jumper respectively.
SKU: 86932 -
Brushed / Brushless DC motor Driver
SmartElex L298N Motor Driver with onboard Arduino Uno + USB Cable
Brushed / Brushless DC motor DriverSmartElex L298N Motor Driver with onboard Arduino Uno + USB Cable
SKU: 599414- 5 mm standard DC plug-in jack for Input supply
- On-Board Arduino UNO with USB Port
- On-Board DC motor Driver L298N.
- On-board 5V 3A SMPS circuit.
- On-Board power supply on-off switch
SKU: 599414 -
-
Battery Chargers, Battery Charging Boards
SmartElex 1S 18650 Li-ion Battery Charger
SKU: 611923- Input Voltage: 4.5V ~ 5.5V.
- Input Interface: 5VDC Micro USB and DC JACK input.
- On-board Battery compatible: – 18650 Li-ion cell.
- Charge Current: up to 1A.
- Over-voltage detection: 4.2V.
- Under-voltage detection: 2.8V.
- Output Interface: – 2 Pin Connector with a properly marked positive and negative signs on PCB.
- LED indicator: Input Power status/ Charging /Charge complete / Battery detects / under-voltage.
SKU: 611923 -
Battery Chargers, Battery Charging Boards
SmartElex 2s 18650 Li-Ion Battery Charger
SKU: 611924- Input Voltage: 5V.
- Max Input Voltage: – 6V
- Input Interface: Micro USB port/ DC jack.
- Charge Current: up to 1A / 2A.
- A full charge voltage: 4.2V.
- Over-Voltage Detection Feature: Yes.
- Under-Voltage Detection Feature: Yes.
- Charging indicator LED: Charging / Full charge/ Battery detects.
- Charging through Micro-USB: YES
- On- Board 18650 cell socket: – Yes.
SKU: 611924 -
Shield for Arduino
SmartElex PS2 Sheild for Arduino
SKU: 217461- Simple to use UART protocol
- Vibrator motor on PS2 is controllable.
- Wired and Wireless PS2 controller is supported.
- PS2 Controller will automatically operate in analog mode. (Default)
- A status LED
- Jumper selector to select different UART Baud Rate (74880 (Default), 9600, 57600, 115200). Default: – when no jumper is attached.
- Jumper selectors to select different digital pin as UART – TX and RX pin.
SKU: 217461 -
Line Sensor
SmartElex RLS-06 Analog & Digital Line Sensor Array
SKU: 63761- Operating voltage: 4.5V to 5.0 V
- Output format: 6 Analog and Digital voltages.
- Optimal sensing distance: 0.125″ (3 mm).
- Potentiometer to adjust the sensitivity of the individual sensors.
- The module is a convenient carrier for six IR emitter and receiver pairs evenly paced.
- Great useful in building fast line following and grid navigating robots
- Comes with easy to use digital outputs that can be connected directly to microcontrollers
SKU: 63761 -
Line Sensor
SmartElex RLS-08 Analog & Digital Line Sensor Array
SKU: 78725- Operating voltage: 4.5V to 5.0 V
- Supply current: 150 mA
- Output format: 8 Analog and Digital voltages.
- Optimal sensing distance: 3 mm.
- Maximum recommended sensing distance: 6 mm
- Potentiometer to adjust the sensitivity of the individual sensors.
- Uses 8 sensors for best resolution
- Comes with easy to use digital outputs that can be connected directly to microcontrollers
SKU: 78725 -
Line Sensor
SmartElex RLS05 Line Follower Sensor Module
SKU: 74474- Operating Voltage Range: 9~12V
- Maximum Operating Current: 130 mA
- Optimal Sensing Distance: 0.125″ (3 mm).
- Fast response time
- High sensitivity
- 5 Analog and 5 Digital Output signals with Respective LED.
- Each IR has indicating LED (D0-D4).
- Available SPI and Serial communication Pins.
SKU: 74474 -
Robot Kits and Parts
SmartElex Wireless Remote Control L293D Motor Driver
SKU: 593215- Remote (Transmitter) side(Input Voltage) :Â 9V battery
- Receiver(Motor driver) side(Input Voltage) : 12Vdc
- On-Board 9v battery socket on the remote sideboard
- Maximum Current:Â 1 Amp Per Channel
- Number of Channel:Â 4
- Antenna Gain (peak): 2Dbi
SKU: 593215 -
Brushed / Brushless DC motor Driver
SmartElex Wireless Remote Control with NRF24L01+PA+LNA SMA Antenna
Brushed / Brushless DC motor DriverSmartElex Wireless Remote Control with NRF24L01+PA+LNA SMA Antenna
SKU: 664890- It uses 2.4GHz global open ISM band, with license-free.
- Operating Range: 1Km
- Antenna Gain (peak): 2Dbi.
- Transmit power is greater than +20 dBm.
- Support six-channel data reception.
SKU: 664890
