Search results: “dwin display” – Page 19
Showing 865–912 of 1013 results
-
Battery Chargers
SKYRC T200 1-6S LiPo/LiFe/LiIon Dual Balance Charger
SKU: 886265- Multiply the Efficiency With Duo
- Multi-purpose for Most Chemistries With Generic XT60
- Versatile With the Addition of Agm and Cold Modes
- Optimized Operating Software
- Intuitive Operation
- Terminal Voltage Control(TVC)
- Portable With a Handle
- Universal-Voltage Input
- Comply with safety and EMC regulation
SKU: 886265 -
FPV Cameras
Runcam Hybrid Dual Split FPV Camera
SKU: 867180- Operating Voltage (VDC):5 ~ 12
- Image Sensor:SONY 8MP
- Signal System:NTSC (720*480)/PAL (720*576) Switchable
- Max. Operating Current (mA):480
- Electronic Shutter Speed: Auto
- Lense Viewing Angle (FOV):HD Recording FOV 145°(FPV FOV 150° @ 4: 3)
SKU: 867180 -
Other Measuring Instrument
GW Instek GPT 9601 Electrical Safety Tester
SKU: 800097- 5 kV AC, 20 mA, 100 VA AC
- 240 x 48 Ice Blue Dot Matrix LCD
- True RMS Current Measurement
- Zero-Crossing Turn-on Operation
- Safety INTERLOCK Function
- PWM Switching Amplifier to Enhance the Power Efficiency and Reliable Testing
- Automatically Switching Input Source for Universal Input Voltage
- Interface: Remote Terminal, Signal I/O
SKU: 800097 -
Ammeter and Voltmeter
USB Charger Doctor (Voltmeter Ammeter)
SKU: 11594- Compact and easy to carry, no additional power supply, plug, and play
- It can easily measure the output voltage of the USB port and the device operating current or load voltage
- Detect any USB charger such as PC USB, home charger, car charger
- Operating Voltage: 3.5 to 7 V
- Maximum Current: 3 A
SKU: 11594 -
-
-
Parallel Charging Board
Parallel charging Board for 6 packs 2~6S (XT60-Male)
SKU: 992293- Charge Cell: 2~6S.
- Connector type: XT Connector Male/JST-XH
- Operating Voltage: 0~22.2VDC.
- Max current: 30A.
- Battery: 6 packs (same capacity & cell count).
- Thicken PCB copper foil, allow security using 40A charging current.
- Amass 7U gold plating plug plating.
- Use a safety fuse (50A) to protect the circuit.
SKU: 992293 -
-
-
-
Addressable LED and Drivers
8 Bit WS2812 5050 RGB LED Built-in Full Color Driving Lights Circular Development Board
Addressable LED and Drivers8 Bit WS2812 5050 RGB LED Built-in Full Color Driving Lights Circular Development Board
SKU: 43798- Outer Diameter: 32 mm.
- Supply Voltage: DC 4-7V.
- LED Driver IC:Â WS2812
- Communication interface: single wire communication.
- Send data at speeds of 800Kbps.
- The color of the light was highly consistent
- Full-color module, Full-color soft lights a lamp strip.
SKU: 43798 -
Addressable LED and Drivers
WS2812B 4×4 RGB LED Module
SKU: 975858- Supply Voltage: DC 4-7V.
- LED driver chip: WS2812B
- Communication interface: single wire communication.
- Send data at speeds of 800Kbps.
- The color of the light was highly consistent
- Full-color module, Full-color soft lights a lamp strip.
SKU: 975858 -
3D Printer Display and Controller
1.4 MKS Gen L V1.0- Mega2560 R3 RAMPS 3D Printer Controller Board
SKU: 723872- 2560 and Ramps 1.4 are integrated into the board
- Support 12V-24V power input
- Arduino MEGA compatible Atmega2560 and FT232 processors compatible with all RAMPS class firmware
- Easy DISPLAY + SD-CARD connector, RepRapDiscount SmartController compatible pin header on board
- Easy connect MKS TFT to AUX-1
- 3x temperature ADC connectors for thermistors
- Up 5 motor driver with A4982
- 4x PWM enable mosfet outputs voltage selector switch for MainPower. (Bed, Extruder0, Extruder1, Fans)
- 4 layers PCB, optimize heat dissipation.
SKU: 723872 -
-
AVR Development Board
SmartElex ATmega32 Development Board on-board Programmer
SKU: 80650- Onboard 5V regulator (78M05) circuit.
- On-Board power supply on-off switch
- Power Status LED (RED)
- User LED D0, D1 connected to any port pin through D0, D1 Jumper respectively.
- User Switch SW1, SW2 connected to any port pin through SW1, SW2 Jumper respectively.
- Onboard 12 MHz crystal
- Port extensions for all ports with detailed pin labeling for easy identification of pins
- Onboard USB TO Serial – CH340 Chip.
- On-board Micro USB USBASP for loading HEX file.
- Servo motor Connector (Run only up to 300mA).
SKU: 80650 -
-
PIC Development board
40 pins PIC Start-Up Kit Combo 1 – SK40C PIC16F877A (SK40C1)
SKU: 10097-
ICSP connector for UIC00B -simple and fast method to load program.
-
Perfect fit for 40 pins PIC16F and PIC18F.
-
2 x programmable switch.
-
2 x LED indicator.
-
Exchangeable Crystal.
-
Existing pad for 16 x 2 characters LCD display.
SKU: 10097 -
-
FPV/Telemetry Trans-Receiver
RC832 Plus 5.8G 48CH Wireless AV Receiver
SKU: 57268- Operating Voltage: 12VDC
- Working current:Â 200mA max.
- Video format:Â NTSC/PAL auto.
- Control Range: Approx 5 KM
- 48 channels: Cover A, B, E, F, HÂ bands and L bands.
- Â Power off memory for last channel and band.
- Â Dual Independent video and audio signal outputs.
SKU: 57268 -
Raspberry Pi Accessories
Mini HDMI To HDMI Cable 1 Meter Round High-Quality Copper-Clad Steel Black
SKU: 52808- Length: 1 M.
- Weight: 48 gm.
- Color: Steel Black
- High-Speed HDMI
- Fully shielded audio and video lines for optimum reduction of electromagnetic interference.
- 3d Transmission due to extending bandwidth.
- Maximum Digital Resolutions:Â 4K x 2K @ 30 Hz
SKU: 52808 -
FPV Cameras
RunCam Swift 2 600TVL FPV Camera Integrated OSD 2.3mm Lens
SKU: 674102- The lightest FPV HD camera
- Support WiFi transmission, IOS, and Android APP
- Better Button Structure, New Touch Feeling
- Anti-interference PCB can effectively reduce RF interference.
- The bottom door keeps the micro SD card from popping out in a crash.
SKU: 674102 -
Water TDS, pH, Flow, Level and Pressure Sensor
DFRobot Fermion: ICP-10111 Pressure Sensor (Breakout)
SKU: 1254407- Relative accuracy ±1Pa, as small as 8.5cm height measurement difference
- ±0.5Pa/℃ temperature coefficient offset, high stability for long-term use
- 0.4Pa pressure noise, more stable data
SKU: 1254407 -
ESP WiFi Module
Waveshare ESP32-S2 MCU WiFi Development Board, 240MHz, 2.4 GHz WiFi, LCD Version with pinheader
ESP WiFi ModuleWaveshare ESP32-S2 MCU WiFi Development Board, 240MHz, 2.4 GHz WiFi, LCD Version with pinheader
SKU: 1219063- Based on ESP32 240MHz Xtensa dual-core 32-bit microprocessor
- Operating Voltage: 2.7V – 4.2V
- Working Current: 60mA
- Battery Charging Current: 500mA
- On-board 0.96inch 160×80 pixels 65K color IPS LCD display
- On-board single 3.7V lithium battery charge/discharge header, suitable for mobile IoT product design
SKU: 1219063 -
Stepper Motor Drivers
ULN2003 Driver Module Stepper Motor Driver
SKU: 28379- 5-12V power supply
- 4-way signal indicator
- Chip all the pins have Input leads Mounted for easy connection to use
- XH-5P socket can be connected directly 28BYJ-48 Model stepper motor
- Dimensions: 32 x 18 x 11mm (LxWxH)
- Weight: 3 gm
SKU: 28379 -
Raspberry Pi, Official Boards and Hats
Raspberry Pi Zero v1.3 Development Board
SKU: 31905The Raspberry Pi Zero v1.3 is super low cost and smaller than it’s bigger brother, the Raspberry Pi 3. The Raspberry Pi Zero v1.3 now comes complete with a camera port. Using the new Raspberry Pi Zero Camera Adapter, you can now connect a Raspberry Pi camera to your Zero.
HAT Compatibility:
The Pi Zero is fully compatible with all HAT breakout boards, as it features the same 40 Pin GPIO as the Raspberry Pi 2/B+/A+
SKU: 31905 -
Addressable LED and Drivers
SeeedStudio Grove RGB LED Stick (10 – WS2813 Mini)
SKU: 600011- Gray levels of each pixel are of 256
- 6777216 full-color display
- Dual-signal wires version, signal break-point continuous transmission
- Intelligent reverse-connection protection.
- Refresh frequency: 2KHz (max)
- Color: Red, green, and blue
- WS2813B IC, 3535 LED components
- Operating voltage: 3.3V / 5V
- RGB channel constant current: 16mA
- Interface: Digital
SKU: 600011 -
Fuse
Orange -240Pcs/Box 24Values 6x30mm Fast blow Ceramic Fuse 250V 0.1A 0.2A 0.5A 1A 1.5A 2A 2.5A 3A 3.15A 4A 5A 6A 10A 15A 20A 25A30A
FuseOrange -240Pcs/Box 24Values 6x30mm Fast blow Ceramic Fuse 250V 0.1A 0.2A 0.5A 1A 1.5A 2A 2.5A 3A 3.15A 4A 5A 6A 10A 15A 20A 25A30A
SKU: 1187621- Type: ceramic, miniature
- Optimum performance
- Ceramic Fuse 250 & 500 Volt
- Ceramic fuses protect against overcurrent in high-current circuits found in AC or DC electronics, appliances
SKU: 1187621 -
Light/color Sensor
CJMCU 9930 APDS-9930 Digital Proximity And Ambient Light Sensor For Arduino
SKU: 43919- Working voltage:2.8-3.8V
- ALS, IR LED and Proximity Detector in an Optical Module;
- Ambient Light Sensing (ALS);
- Approximates Human Eye Response;
- Programmable Interrupt Function with Upper and Lower Threshold;
- Up to 16-Bit Resolution;
- High Sensitivity Operates Behind Darkened Glass;
- Low Lux Performance at 0.01 lux;
SKU: 43919 -
Parallel Charging Board
Parallel charging Board for 6 packs 2~6S (T-Male)
SKU: 5186- Charge Cell: 2~6S.
- Connector type: T Connector Male/JST-XH
- Operating Voltage: 0~22.2VDC.
- Max current: 30A.
- Battery: 6 packs (same capacity & cell count).
- Thicken PCB copper foil, allow security using 40A charging current.
- Amass 7U gold plating plug plating.
- Use a safety fuse (50A) to protect the circuit.
SKU: 5186 -
Vibration/Tilt Sensor
DFRobot Gravity Flexible Piezo Film Vibration Sensor
SKU: 1209998- Operating Temperature: 0ºC to 85ºC.
- Storage Temperature: -40ºC to 85 ºC.
- Higher Temperature Version up to 125 ºC available on a Custom Basis.
- Operating Voltage: 5V.
- Interface Type: Gravity PH2.0 3Pin interface.
SKU: 1209998 -
PIC Development board
40 pins PIC Start-Up Kit Combo 2 SK40C + PIC18F4550 (SK40C2)
SKU: 10105-
ICSP connector for UIC00B -simple and fast method to load program.
-
Perfect fit for 40 pins PIC16F and PIC18F.
-
2 x programmable switch.
-
2 x LED indicator.
-
Exchangeable Crystal.
-
Existing pad for 16 x 2 characters LCD display.
-
UART connection to interface with other controller or even computer.
-
USB on board for certain PIC18F.
SKU: 10105 -
-
Addressable LED and Drivers
16Bit WS2812B 5050 RGB LED Built-in Full Color Driving Lights Circular Development Board
Addressable LED and Drivers16Bit WS2812B 5050 RGB LED Built-in Full Color Driving Lights Circular Development Board
SKU: 43648- Outer Diameter: 68 mm.
- Supply Voltage: DC 4-7V.
- LED driver chip:Â WS2812B
- Communication interface: single wire communication.
- Send data at speeds of 800Kbps.
- The color of the light was highly consistent
- Full-color module, Full-color soft lights a lamp strip.
SKU: 43648 -
Relay Switch Modules
5V 2A 8-Channel SSR G3MB-202P Solid State Relay Module (Low level Trigger)
SKU: 28508- 8 channel 2 AMP Solid State Relay board
- Control 8 loads of up to 2 amps each at 120V or 240V AC.
- Good for lighting, holiday displays etc.
- Has been assembled, and the electrical test passed.
- Operating Voltage: 5V
- Operating Current: 16mA
- Maximum Load: 2A @ 240VAC
SKU: 28508 -
Breakout Board
PS2 Joystick Module Breakout Sensor
SKU: 11484- Dimensions: 34 x 34 x 15 (LxWxH) mm.
- Weight: 10gm (without Hat).
- 2.54mm pin interface leads.
- Operating Voltage: 5V.
- Long service life and stable performance.
- Standard interface and electronic building blocks.
- Widely use in Arduino DIY projects.
SKU: 11484
