Brushed DC motor Driver
We have a vast collection of different (brushed) DC motor drivers for different DC motors. This brushed DC motor driver is the simplest of all and can be used for most applications. The DC motor drive is a type of amplifier or power modulator that integrate between the controller and a DC motor. It takes the low current and then converts it into a high current which is appropriate for the motor.
DC drive converts an Alternating Current (AC) into Direct Current (DC) to run a DC motor. Higher motor speed generates more voltage in the tachometer and the drive references this voltage to make sure the motor is running at the correct speed per-user settings. This is used mainly for good speed regulation, frequent starting, braking and reversing.
-
Cytron 30Amp DC Motor Driver (Peak 80Amp) MD30C R2
₹ 3,045.00(inc GST)
₹ 2580.51 (+18% GST extra)
- Bi-directional control of 1 brushed DC motor.
- Motor Voltage: 5V – 30V.
- Maximum Current: 80A peak (1 second), 30A continuously.
- Reverse polarity protection.
- 3.3V and 5V logic level input.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
-
Cytron Enhanced 13Amp DC Motor Driver 30A peak (10 seconds) MD10C
₹ 935.00(inc GST)
₹ 792.37 (+18% GST extra)
- Bi-directional control for 1 brushed DC motor, single channel
- Support motor voltage ranges from 5V to 30V.
- Maximum current up to 13A continuous and 30A peak (10 seconds).
- 3.3V and 5V logic level input.
- Solid state components provide faster response time and eliminate the wear and tear of the mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
-
Cytron SmartDrive40 40AMP DC MOTOR DRIVER (PEAK 80AMP) MDS40A
₹ 5,239.00(inc GST)
- Bi-directional control for a single brushed DC motor.
- Support motor from 7V to 25V.
- Maximum current up to 80A peak (1 second), 40A (5 minutes) or 30A (> 20 minutes) continuously.
- 16 KHz switching frequency for quiet operation.
- Reverse polarity protection.
- LiPo battery low voltage warning.
- Thermal protection.
- Current limiting base on temperature.
-
Cytron MDS160A SmartDrive160 160AMP Dc Motor Driver (Peak 190Amp)
₹ 24,299.00(inc GST)
₹ 20592.37 (+18% GST extra)
- Bi-directional control for a single brushed DC motor.
- Support input voltage from 8V to 28V.
- Maximum current up to 190A peak (1 minute), 175A (2 minutes) or 160A (continuously).
- 16 KHz switching frequency for quiet operation.
- LiPo battery low voltage warning.
- Thermal protection.
-
Cytron MDD10A Dual Channel Enhanced 10Amp DC Motor Driver 30A Peak
₹ 1,890.00(inc GST)
₹ 1601.69 (+18% GST extra)
- Bi-directional control of 2 brushed DC motor.
- Support motor voltage ranges from 5V to 25V.
- Maximum current up to 10A continuous and 30A peak (10 seconds) for each channel.
- Solid state components provide faster response time and eliminate the wear and tear of the mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
-
Cytron SmartDriveDuo-10 MDDS10 DC MOTOR DRIVER
₹ 3,937.00(inc GST)
₹ 3336.44 (+18% GST extra)
-
Single power operation
-
Dual Channels means it can drive two brush motor independently, or mixed.
- Support Signed magnitude and Locked Anti-phase in PWM mode.
-
Two manual/test buttons for each channel.
-
Two output indicator LEDs for each channel.
-
Power, Error indicator, RUN status (Left and Right) LEDs
-
On board reset button to restart the MCU after changing operation mode.
-
Operating modes: RC (RC servo signal), Analog, PWM, simplified and packetized UART.
-
-
Sabertooth Dual 5A Motor Driver
₹ 4,189.00₹ 3,049.00(inc GST)
₹ 2583.9 (+18% GST extra)
You save(27.2%): ₹ 1,140.00
- Input Voltage: 6V to 18V
- Compatible with: 6-12 cell NiMH or NiCd, 2s-4s LiPo
- 5A continuous per channel, 10A peak
- Synchronous regenerative drive
- Ultra-sonic switching frequency
- Thermal and overcurrent protection
- Lithium protection mode
-
Sabertooth Dual 5A Motor Driver for R/C
₹ 4,189.00(inc GST)
₹ 3550 (+18% GST extra)
- Operating Voltage(VDC): 6-18
- Peak Current (A): 10
- Continuous Current (A): 5
- No. of Channels: 2
- Synchronous regenerative drive
- Ultra-sonic switching frequency
- Thermal and overcurrent protection
- Lithium protection mode-compatible with: 6-12 cell NiMH or NiCd, 2s-4s LiPo, 6V or 12V lead acid (not 18+V lead acid!)
-
Sabertooth Dual 12A Motor Driver
₹ 5,554.00(inc GST)
₹ 4706.78 (+18% GST extra)
- 12A continuous, 25A peak per channel Up to 24V in
- Synchronous regenerative drive
- Ultra-sonic switching frequency
- Thermal and overcurrent protection
- Lithium protection mode
- Peak Current (A): 25A
- Continuous Current (A): 12
- Operating Voltage(VDC): 18 to 24V
- No. of Channels: 2
-
Sabertooth Dual 25A Motor Driver
₹ 9,082.00(inc GST)
₹ 7696.61 (+18% GST extra)
- 25A continuous, 50A peak per channel
6-30V nominal, 33.6V absolute maximum - Synchronous regenerative drive
- Ultra-sonic switching frequency
- Thermal and overcurrent protection
- Lithium protection mode
- Input modes: Analog, R/C, simplified serial, packetized serial
- 25A continuous, 50A peak per channel
-
Sabertooth Dual 32A Motor Driver
₹ 9,439.00(inc GST)
₹ 7999.15 (+18% GST extra)
- 32A continuous, 64A peak per channel
- 6-30V nominal, 33.6V absolute maximum
- Synchronous regenerative drive
- Ultrasonic 30 kHz switching frequency
- Thermal and overcurrent protection
- Battery protection mode
- USB control and monitoring
- USB serial converter mode for Kangaroo x2
- Configurable current limiting
- Custom user modes
- 12-bit motor outputs
-
L293D Motor Driver Module
₹ 119.00(inc GST)
₹ 100.85 (+18% GST extra)
- The driver two holes of 3 mm dia.
- Male burg-stick connectors for supply, ground and input connection.
- Screw terminal connectors for easy motor connection.
- High noise immunity inputs.
- Operating Voltage(VDC): 4.5 to 12
- Peak Current (A): 600 mA
- No. of Channels: 1
-
SmartElex 30D Dual Channel 30A Smart DC Motor Driver
₹ 3,799.00(inc GST)
₹ 3219.49 (+18% GST extra)
- Supplying 30 amps continuous with peak currents up to 85 amps (2 Sec) per channel.
- Support motor voltage from 7V to 30V.
- Onboard Low Internal resistance MOSFETs are switched at 16 KHz frequency.
- Overcurrent protection and indication.
- Thermal protection.
- Multiple input modes: RC, Analog, PWM, Serial Packetized.
- On board push buttons for test and manual operation.
-
SmartElex 15D Smart Motor Driver
₹ 1,980.00(inc GST)
₹ 1677.97 (+18% GST extra)
- Support motor voltage from 7V to 28V.
- Onboard Low, Internal resistance MOSFETs are switched at 16 KHz frequency.
- Overcurrent and Thermal protection.
- Multiple input modes: RC, Analog, PWM, Serial Packetized.
- On board push buttons for test and manual operation.
-
SmartElex 10S DC Motor Driver HAT
₹ 749.00(inc GST)
₹ 634.75 (+18% GST extra)
- Wide 6V to 28V motor Operating Voltage.
- One brushed DC motor Bidirectional control.
- Current limiting at 35A.
- PWM frequency up to 32KHz
- Support TTL PWM from the microcontroller
- Internal thermal shutdown
- Under-voltage lockout
-
SmartElex 10D Motor Driver for Arduino UNO
₹ 1,790.00(inc GST)
₹ 1516.95 (+18% GST extra)
- Onboard 5V 3A Buck Converter.
- Continuous 10A maximum current without Heatsink and 30A peak current for 10
- Two brushed DC motor Bidirectional control.
- Current limiting at 35A.
- PWM and direction controlled driving of four externally powered NMOS transistors
-
SeeedStudio Grove I2C Motor Driver (TB6612FNG)
₹ 699.00₹ 659.00(inc GST)
You save(5.7%): ₹ 40.00
- MCU Operating Voltage: 3.3V / 5V
- Motor Supply Voltage: 2.5 ~ 13.5 (5V Typical, 15V Max.)
- Output Current: 1.2 A(ave)/3.2 A (peak)
- Switching Frequency: 100kHz
- Logic Interface: I2C
- I2C Address: 0x14 (default)
-
Motor Driver TB6612FNG Module Performance Ultra Small Volume 3 PI Matching Performance Ultra L298N
₹ 199.00(inc GST)
₹ 168.64 (+18% GST extra)
- CW/CCW/short break/stop motor control modes
- Built-in thermal shutdown circuit and a low voltage detecting circuit
- Standby control to save power
- CW/CCW/short brake/stop motor control modes
- Operating Voltage(VDC): 15
- Peak Current (A): 3.2
- Continuous Current (A): 1.2
- No. of Channels: 1
-
Monster Moto Shield VNH2SP30 Motor Driver 14A (Peak 30A)
₹ 349.00(inc GST)
₹ 295.76 (+18% GST extra)
- Voltage Max: 16V
- Maximum current rating: 30 A
- Practical Continuous Current: 14 A
- Current sensing available to Arduino analog pin
- MOSFET on-resistance: 19 mΩ (per leg)
- Maximum PWM frequency: 20 kHz
- Thermal Shutdown
- Undervoltage and Overvoltage shutdown.
-
Mini Motor Drive Shield Expansion Board L293D Module for Arduino UNO MEGA 2560
₹ 129.00(inc GST)
₹ 109.32 (+18% GST extra)
- New L293D motor shield, the input voltage DC4.5-25V
- 600mA output current capability per channel
- 1.2A peak output current(non-repetitive) per channel
- Enable facility
- Overtemperature protection
- Logical “0” input voltage up to 1.5V(High noise immunity)
-
MD13S 13Amp DC Motor Driver – GROVE Compatible
₹ 891.00(inc GST)
₹ 755.08 (+18% GST extra)
-
Support motor voltage ranges from 6V to 30V
-
Maximum current up to 13A continuous and 30A peak (10 seconds).
-
GROVE compatible
-
3.3V and 5V logic level input.
-
SMD compatible
- Peak Current (A): 30 (10 seconds)
- Continuous Current (A): 1
- No. of Channels: 1
-
-
L298N 2A Based Motor Driver Module – Good Quality
₹ 222.00₹ 125.00(inc GST)
₹ 105.93 (+18% GST extra)
You save(43.7%): ₹ 97.00
- Current Sense for each motor.
- Heatsink for better performance.
- Power-On LED indicator.
- Double H bridge Drive Chip: L298N.
- Operating Voltage(VDC): 5~35
- Peak Current (A): 2
- Continuous Current (A): 0-36mA
- No. of Channels: 2
- Over-Current Protection (A): Yes
- Thermal Protection: Yes
-
L293D Motor Driver Board for ESP8266 WiFi NodeMcu Lua ESP12E
₹ 189.00(inc GST)
- Motor Power Range: 4.5V ~ 36V
- Control supply range: 4.5V ~ 9V
- Logical operating current Iss: ≤60mA
- Driving part of the work current Io: ≤1.2A
- Maximum power dissipation: 4W (T = 90 ℃)
- Operating temperature : -25 ℃ ~ + 125 ℃
- Drive Type: Dual high-power H-bridge driver
-
Kangaroo X2 Motion Controller
₹ 1,879.00(inc GST)
₹ 1592.37 (+18% GST extra)
- Model: Kangaroo x2
- 2 channel self-tuning PID controller
- Position or speed control
- Quadrature encoder feedback or potentiometer feedback
- Support for limit switches and mechanical stops
- Analog, R/C, and serial inputs
-
Enhanced Cytron 40Amp DC Motor Driver (Peak 80amp) MDS40B
₹ 6,191.00(inc GST)
₹ 5246.61 (+18% GST extra)
-
Bi-directional control for a single brushed DC motor.
-
Support motor from 10V to 45V.
-
Maximum current up to 80A peak, reduce to 40A gradually according to temperature.
-
16 KHz switching frequency for quiet operation.
-
NO Reverse polarity protection.
-
Protection of overvoltage.
-
-
Dual Monster Moto Shield VNH3ASP30 DC Motor Driver 2x14A (Peak 30A)
₹ 699.00(inc GST)
₹ 592.37 (+18% GST extra)
- Voltage Max: 16V
- Maximum current rating: 30 A
- Practical Continuous Current: 14 A
- Current sensing available to Arduino analog pin
- MOSFET on-resistance: 19 mΩ (per leg)
- Maximum PWM frequency: 20 kHz
- Thermal Shutdown
- Undervoltage and Overvoltage shutdown.
-
Cytron SmartDriveDuo-60 MDDS60 60A (100A peak)
₹ 12,064.00(inc GST)
₹ 10223.73 (+18% GST extra)
-
Input Voltage (Motor): 10 – 45VDC
- Maximum current up to 100A peak (1 second), 60A continuously, each channel.
-
Two manual/test buttons for each channel.
-
Two output indicator LEDs for each channel.
-
Suitable for combat or sumo robot.
- Battery Low Voltage Monitoring Mode
- DC Brush motor Driver, not for brushless motor
- Dual Channels, it can drive two brush motor independently, or mixed.
-
-
CYTRON SMART DRIVE MDDS30 DUAL 30A (80A Peak)
₹ 5,490.00(inc GST)
₹ 4652.54 (+18% GST extra)
- Battery low voltage indicator.
- Battery over voltage indicator.
- Thermal protection.
- Current limit protection.
- Bi-directional control for dual brushed DC motor.
- Support motor voltage from 7V to 35VDC.
- Dimension: 103 x 97 x 40 (LxWxH) mm.
-
Cytron FD04A 4-Channel Motor Driver
₹ 2,362.00(inc GST)
₹ 2001.69 (+18% GST extra)
- Industrial grade PCB.
- Vmotor: 7 V to 25 V DC.
- Each component is soldered properly and tested.
- Able to drive 4 DC motor at 2.5A (peak), 1.5A continuously.
- 2 LEDs as a direction indicator for each motor.
- 1 LED as a power indicator.
- A pluggable connector for more user-friendly design.
- Fully compatible with Cytron DIY project, Flexibot – Using Transwheel (PR19).
-
Cytron Dual channel 10A Motor Driver UNO Robot Controller
₹ 2,510.00(inc GST)
₹ 2127.12 (+18% GST extra)
- Onboard 1A (maximum) 5V voltage regulator.
- Onboard 500mA (maximum) 3.3V voltage regulator.
- 0-5V digital outputs with 3.3V compatible inputs.
- 14 Digital I/O Pins (6 PWM outputs).(4 pin used for Motor driver)
- 6 Analog Inputs (Can be digital I/O too).
- Maximum current up to 10A continuous and 30A Peak.
- ISP 6-pin Header.
- 32k Flash Memory.
- 16MHz Clock Speed.
- R3 Shield Compatible.
-
Cytron Driver HAT-MDD10
₹ 1,890.00(inc GST)
₹ 1601.69 (+18% GST extra)
- Support motor voltage ranges from 6VDC to 24VDC.
- Onboard the test button for manual control of the motor.
- Every channel output built with LED indicator.
- Current limiting at 30A.
- Operating Voltage(VDC): 6 to 24
- Peak Current (A): 30 (10 seconds)
- Continuous Current (A): 10
- No. of Channels: 2
- Operating Modes: PWM (Lock-Antiphase and Sign-Magnitude): Yes, UART: No, Analog:No, RC Servo Signal: No
-
Cytron 25A 7V-58V DC motor driver with Switch and Potentiometer Control (MD25HV POT)
₹ 3,854.00(inc GST)
₹ 3266.1 (+18% GST extra)
- Bidirectional control for one brushed DC motor.
- Maximum Motor Current: 25A continuous, 60A peak.
- 5V output for the host controller (250mA max).
- Buttons for quick testing.
- PWM frequency up to 40kHz.
- Dual Input Mode: PWM/DIR or Potentiometer/Switch Input.
-
Cytron 10 A Switch Control Potentiometer DC Motor Driver (MD10POT)
₹ 790.00(inc GST)
₹ 669.49 (+18% GST extra)
The MD10-POT control circuit is designed to enable the speed to be controlled via a potentiometer (10K Ohm) which is included in the package. It does not work with analog voltage from an external controller The 3-way rocker switch is used for start/stop and direction control.
-
20A PWM DC Motor Speed Regulator Module (9V, 12V, 24V, 36V, 48V, 60V)
₹ 590.00(inc GST)
₹ 500 (+18% GST extra)
- Adjustable speed range: 0%-100%.
- Speed adjustment way: Potentiometer.
- Output voltage: Linear under load.
- Speed control type: Basins.
- Output voltage: Load Linear
- Type: Adjusting flow
- The motor running condition adjustment: Forward / Stop / Reverse