Stepper Motor Drivers
A stepper motor driver is the driver circuit that controls how the stepper motor operates. Stepper drives work by sending current through various phases in pulses to the stepper motor. Here is a vast collection of the different stepper motor. There are four types: wave drives, two-phase on, one-two phase-on drives and micro-stepping drives.
Stepper motor drivers vary in complexity. Modern drivers may be combined with a host of different stepper motor types. This stepper motor driver is used along with stepper motor which is used for precise positioning with a motor, such as hard disk drives, robotics, antennas, telescopes, and some toys.
-
DRV8825 Stepper Motor Driver with Aluminum Heat Sink
₹ 229.00₹ 120.00(inc GST)
₹ 101.69 (+18% GST extra)
You save(47.6%): ₹ 109.00
- Supply Voltage: 8.2 – 42 VDC.
- Current Capacity : 2.2A max(24V).
- Continuous current per phase: 1.5 A.
- Minimum Logic voltage: 2.5V.
- Maximum Logic Voltage: 5V.
- Microstep resolutions:Â full, 1/2, 1/4, 1/8, 1/16, and 1/32.
- Dimensions : 15 x 20 mm.
- Weight: 4 gm.
-
A4988 driver Stepper Motor Driver- Good Quality
₹ 139.00(inc GST)
₹ 117.8 (+18% GST extra)
- Supply Voltage : 8-35 VDC.
- Current : 1.0A Â (no heatsink ).
- Current : 2.0A (with heat-sinking).
- logic input : 3 – 5.5V .
- Automatic current decay mode detection / choice.
- Mixed with slow current decay mode.
-
Leadshine DM542 Digital Stepper Motor Driver
₹ 2,999.00(inc GST)
₹ 2541.53 (+18% GST extra)
- Good high-speed performance
- Supply voltage up to +50VDC
- Output current up to 4.2A
- Pulse frequency up to 300 KHz
- Automatic idle-current reduction
- 3-state current control technology
- Self-adjustment technology
- Pure-sinusoidal current control technology
-
MA860H Digital Stepper Micro-Step CNC Motor Driver 50-110 VDC with 1.8-7.5A
₹ 6,667.00(inc GST)
₹ 5650 (+18% GST extra)
- Supply voltage up to 80VAC or +110VDC
- Output current up to 7.2A
- Pulse input frequency up to 300 KHz
- 16 selectable resolutions in decimal and binary, up to 51,200 steps/rev
- Suitable for 2-phase and 4-phase motors
- Dimensions: 118×75.5×34 (LxWxH) mm
-
ULN2003 Driver Module Stepper Motor Driver Board
₹ 79.00(inc GST)
₹ 66.95 (+18% GST extra)
- ULN2003A motor driver chip
- Chip all the pins already leads for easy connection to use
- 5-12V power supply
- 4-way signal indicator
- Step angle: 5.625 x 1 / 64
- Reduction ratio: 1 / 64
- Phase: 4
- Current / Phase: 5V
-
ULN2003 Driver Module Stepper Motor Driver
₹ 79.00(inc GST)
₹ 66.95 (+18% GST extra)
- 5-12V power supply
- 4-way signal indicator
- Chip all the pins have Input leads Mounted for easy connection to use
- XH-5P socket can be connected directly 28BYJ-48 Model stepper motor
- Dimensions: 32 x 18 x 11mm (LxWxH)
- Weight: 3 gm
-
TMC2208 Stepper Motor Driver Module
₹ 899.00(inc GST)
- Voltage range: 3.3-5V
- Maximum current: 1.2A per phase (continuous, with cooling), 2A peak per phase
- Works with 3.3V and 5V signals
- Comes with heatsink for better cooling
- Has StealthChop technology for quieter stepper motors
- Has SpreadCycl technology for smoother movements
-
TL-Smoother Eight Chip Module DFORCE Vibration Pattern Filter with Cable
₹ 149.00(inc GST)
- TL Smoother can effectively eliminate the mechanical chatter generated by 3D printer motors,
- The TL-Smoother is an addon module for 3D printer stepper motor drivers.
- The board provides flyback diodes for the motor outputs, so they are also protected against inductance voltages in the unpowered state of the driver.
- You will get smoother movement, especially on the delta-style 3D printer
- I3 and UM models can also be used, and different machines will have different clipping effects.
-
TB6600 Stepper Motor Driver Controller 8~50V 4.5A
₹ 649.00(inc GST)
₹ 550 (+18% GST extra)
- Supply Voltage: 8V – 50V DC (36V recommended).
- Output current: 0.3A – 4.5A (peak value of 5A).
- Micro Step: 1, 2, 8, 16.
- Maximum PWM frequency:Â 200kHz.
- Adjustments for the maximum current of the LED: 1A, 2.2A, 3.3A, 4.5A.
- Operating temperature: -10 to + 45 ° С.
-
TB6600 Stepper Motor Driver Controller 4A 9~42V TTL 16 Micro-Step CNC 1 Axis
₹ 649.00(inc GST)
₹ 550 (+18% GST extra)
- Input Current: 0~5A
- Output Current: 0.5~4.0A
- Control Signal: 3.3~24V
- Power (MAX): 160W
- Micro Step: 1, 2/A, 2/B, 4, 8, 16, 32
- Temperature: -10~45℃
- H bridge bipolar constant current drive.
-
TB6560 Driver Board 3A CNC Router Single 1 Axis Controller Stepper Motor
₹ 499.00(inc GST)
₹ 422.88 (+18% GST extra)
- Driver Chip: TB6560AHQ
- Operating Voltage: 10-35V
- Nominal Voltage: 24V
- With the large heat sink to ensure good heat dissipation
- 6N137 high-speed OptoCoupler, to ensure a high speed without step out.
-
MKS-LV8729-OC 1.5A Ultra Quiet Stepper Motor Driver for 3D Printers and CNC
₹ 999.00(inc GST)
- High-speed optocoupler, high-speed without losing a step
- LV8729 chip, with over-current protection circuit, the maximum support 128 segments
- Automatic half-flow function
- A variety of input methods to meet a variety of interface needs
- The use of increased heat sink, good heat dissipation
-
MKS SBASE V1.3 32-bit Open Source Smoothieboard
₹ 6,999.00₹ 5,999.00(inc GST)
You save(14.3%): ₹ 1,000.00
- Â 32bit 100M Cortex-M3 MCU-LPC 1768
- High-performance
- Support highly modular open source firmware Smoothieware
- Easy for secondary development
- Â Support network function, then proceed remote control via IE Explorer.
-
MACH3 Interface Board CNC 5 Axis with Optocoupler for Stepper Motor Driver and USB cable
₹ 690.00(inc GST)
₹ 584.75 (+18% GST extra)
- Compatible with MACH3, Linux CNC (EMC2) etc. parallel-control CNC software.
- USB power supply and peripherals power phase are separate to protect computer security.
- All the signals are to-isolate which can protect your computer security.
- 5-input interface to define the Limit, Emergence-Stop, Cutter alignment, etc.
- Wide input voltage range: 12-24V, and with anti-reverse function.
- One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
-
LV8729 6V-36V Ultra Quiet 4-layer Substrate Stepper Motor Driver with Heatsink for 3D Printer
₹ 499.00(inc GST)
₹ 422.88 (+18% GST extra)
1. In 64 subdivision or 128 subdivision to achieve a better ultra-quiet effect.
2. Operating voltage: 6V-36V, the proposed voltage is 12V.
3. The maximum current is 1.5A, the default is 0.8A.
4. Segment: 1, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128. -
L9110 L9110S DC Stepper Motor Driver Board HBridge
₹ 119.00(inc GST)
- Â Power supply voltage: DC2.5-12V
- Â Each channel has 800mA continuous current output
- Â Low saturation pressure drop
- Â TTL/CMOS output level compatible can be connected directly to the CPU
- Â Control and drive integrated into IC
- Â Have pin high-pressure protection function
-
L298N Dual H Bridge DC/Stepper Motor Driver Controller Module
₹ 249.00(inc GST)
₹ 211.02 (+18% GST extra)
- Driver chip: L298N Dual H Bridge
- Supply voltage: VMS 5V – 35V
- Peak current IO: 2A per bridge
- Max power consumption: 20W
- Provides 4 LEDs that reflect the state of the control logic
- Independent direction, speed, and braking for each motor
-
DRV8825 Stepper Motor Driver with Aluminum Heat Sink- Good Quality
₹ 249.00₹ 125.00(inc GST)
₹ 105.93 (+18% GST extra)
You save(49.8%): ₹ 124.00
- Supply Voltage: 8.2 – 42 VDC.
- Current Capacity : 2.2A max(24V).
- Continuous current per phase: 1.5 A.
- Minimum Logic voltage: 2.5V.
- Maximum Logic Voltage: 5V.
- Microstep resolutions:Â full, 1/2, 1/4, 1/8, 1/16, and 1/32.
- Dimensions : 15 x 20 mm.
- Weight: 4 gm.
-
Double BTS7960 43A H-Bridge High-Power Stepper Motor Driver Module
₹ 899.00(inc GST)
₹ 761.86 (+18% GST extra)
- Input voltage(V): 6 – 27.
- Maximum current(A): 43.
- Input level(V): 3.3 – 5.
- Duty cycle: 0 – 100%.
- Path resistance: 16 mΩ at 25°C.
- Low quiescent current: 7 µA at 25°C.
-
Cytron Maker Drive H-Bridge Motor Driver
₹ 359.00(inc GST)
₹ 304.24 (+18% GST extra)
- Dual channel, Bi-directional control motor driver
- Support motor voltage from 2.5V to 9.5VDC
- Maximum current up to 1.0A continuous and 1.5A peak (<5 seconds)
- 5V Output (200mA)Â to power the controller.
- Inputs compatible with 1.8V, 3.3V and 5V logic (Arduino, Raspberry Pi, etc).
- Solid state components provide faster response time and eliminate the wear and tear of mechanical relay
- Regenerative Braking
Â
-
Cytron 3Amp 4V-16V Dual Channel DC Motor Driver MDD3A
₹ 615.00(inc GST)
₹ 521.19 (+18% GST extra)
- Bidirectional control for two brushed DC motor.
- Control one unipolar/bipolar stepper motor.
- Operating Voltage: DC 4V to 16V
- Maximum Motor Current: 3A continuous, 5A peak
- Buck-boost regulator to produce 5V output (200mA max).
- Buttons for quick testing.
-
Cytron 20Amp 6V-30V DC Motor Driver MD20A
₹ 1,930.00(inc GST)
₹ 1635.59 (+18% GST extra)
- Bidirectional control for one brushed DC motor.
- Operating Voltage: DC 6V to 30V
- Maximum Motor Current: 20A continuous, 60A peak
- Buttons for quick testing.
- LEDs for motor output state.
- Overcurrent protection with active current limiting.
- Temperature protection.
- Undervoltage shutdown.
-
A4988 Stepper Motor Driver Controller Board- RED
₹ 111.00(inc GST)
- Compact size, easy to install and use.
- All jumpers hit the ON position to indicate 16 subdivisions (4988) or 32 subdivisions (8825).
- Jm connection motor: Jv Connects 5V and 12V-24V Power Supply.
- E /S /D /G of Jc corresponds to Enable /Step /Dir /Gnd driving signal output on the connection respectively.
-
A4988 driver Stepper Motor Driver- Normal Quality
₹ 179.00₹ 95.00(inc GST)
₹ 80.51 (+18% GST extra)
You save(46.9%): ₹ 84.00
- Supply Voltage : 8-35 VDC.
- Current : 1.0A Â (no heatsink ).
- Current : 2.0A (with heat-sinking).
- logic input : 3 – 5.5V .
- Automatic current decay mode detection / choice.
- Mixed with slow current decay mode.
-
3D Printer Controller Board RAMPS 1.4 Arduino Mega Shield RepRap Prusa Model
₹ 588.00(inc GST)
₹ 498.31 (+18% GST extra)
- Supply Voltage: 12V
- Standard interfaces (as that of the extruder)
- Reserved GCI like I2C and RS232
- 3 MOSFET’s are applied to the heater/ fan and thermistor circuit.
- Another 5A added to protect the component parts.
- An 11A fuse is added to the hotbed.
- Support 5 stepper drive board