A stepper motor driver is the driver circuit that controls how the stepper motor operates. Stepper drives work by sending current through various phases in pulses to the stepper motor. Here is a vast collection of the different stepper motor. There are four types: wave drives, two-phase on, one-two phase-on drives and micro-stepping drives.
Stepper motor drivers vary in complexity. Modern drivers may be combined with a host of different stepper motor types. This stepper motor driver is used along with stepper motor which is used for precise positioning with a motor, such as hard disk drives, robotics, antennas, telescopes, and some toys.
Stepper Motor Drivers
Showing all 45 results
-
Stepper Motor Drivers
TMC2100 Stepper Motor Driver, Module
SKU: 1121430- This driver has 200 steps per revolution in full step (1.8 degrees per step).
- Allowable continuous current per phase: 1.25A (RMS) or 1.77A (max)
- The maximum current in the short term for each phase: 2.5A
- Motor voltage: 5.5 to 46 V
- StealthChop mode to reduce noise
- SpreadCycle mode to increase torque
SKU: 1121430 -
Stepper Motor Drivers
TMC2209 Stepper Motor Driver Module with Heatsink
SKU: 1555083- Operating Voltage: 4.5V to 28V DC
- Input Signal Logic Voltage: 3.3V to 5V DC
- Maximum Peak Current: 2A per phase (use with Heatsink and Fan only)
- Maximum Continuous Current: 2A
- Compatibility: 3V3 and 5V microcontrollers
SKU: 1555083 -
-
Stepper Motor Drivers
3D Printer Controller Board RAMPS 1.4 Arduino Mega Shield RepRap Prusa Model
-4%
Stepper Motor Drivers3D Printer Controller Board RAMPS 1.4 Arduino Mega Shield RepRap Prusa Model
SKU: 16048- Supply Voltage: 12V
- Standard interfaces (as that of the extruder)
- Reserved GCI like I2C and RS232
- 3 MOSFET’s are applied to the heater/ fan and thermistor circuit.
- Another 5A added to protect the component parts.
- An 11A fuse is added to the hotbed.
- Support 5 stepper drive board
SKU: 16048 -
Stepper Motor Drivers
3D Printer MKS OSC Stepper Motor Controller Pulse PWM Speed Reversing Module
SKU: 815797This 3D Printer MKS OSC Stepper Motor Controller Pulse PWM Speed Reversing Module is a pulse generating module, which used as a signal for stepper drivers. To control the stepper motor,
SKU: 815797 -
-
-
Stepper Motor Drivers
Green A4988 driver Stepper Motor Driver- Normal Quality
SKU: 1483566- Supply Voltage : 8-35 VDC.
- Current : 1.0A Â (no heatsink ).
- Current : 2.0A (with heat-sinking).
- logic input : 3 – 5.5V .
- Automatic current decay mode detection / choice.
- Mixed with slow current decay mode.
SKU: 1483566 -
Stepper Motor Drivers
A4988 Stepper Motor Driver Controller Board- RED
SKU: 699614- Compact size, easy to install and use.
- All jumpers hit the ON position to indicate 16 subdivisions (4988) or 32 subdivisions (8825).
- Jm connection motor: Jv Connects 5V and 12V-24V Power Supply.
- E /S /D /G of Jc corresponds to Enable /Step /Dir /Gnd driving signal output on the connection respectively.
SKU: 699614 -
-
Stepper Motor Drivers
Cytron 20Amp 6V-30V DC Motor Driver MD20A
SKU: 381393- Bidirectional control for one brushed DC motor.
- Operating Voltage: DC 6V to 30V
- Maximum Motor Current: 20A continuous, 60A peak
- Buttons for quick testing.
- LEDs for motor output state.
- Overcurrent protection with active current limiting.
- Temperature protection.
- Undervoltage shutdown.
SKU: 381393 -
Stepper Motor Drivers
Cytron 3Amp 4V-16V Dual Channel DC Motor Driver MDD3A
SKU: 381249- Bidirectional control for two brushed DC motor.
- Control one unipolar/bipolar stepper motor.
- Operating Voltage: DC 4V to 16V
- Maximum Motor Current: 3A continuous, 5A peak
- Buck-boost regulator to produce 5V output (200mA max).
- Buttons for quick testing.
SKU: 381249 -
Stepper Motor Drivers
Cytron Maker Drive H-Bridge Motor Driver
SKU: 381588- Dual channel, Bi-directional control motor driver
- Support motor voltage from 2.5V to 9.5VDC
- Maximum current up to 1.0A continuous and 1.5A peak (<5 seconds)
- 5V Output (200mA)Â to power the controller.
- Inputs compatible with 1.8V, 3.3V and 5V logic (Arduino, Raspberry Pi, etc).
- Solid state components provide faster response time and eliminate the wear and tear of mechanical relay
- Regenerative Braking
Â
SKU: 381588 -
-
Stepper Motor Drivers
DRV8825 Stepper Motor Driver with Aluminum Heat Sink- Good Quality
SKU: 52599- Supply Voltage: 8.2 – 42 VDC.
- Current Capacity : 2.2A max(24V).
- Continuous current per phase: 1.5 A.
- Minimum Logic voltage: 2.5V.
- Maximum Logic Voltage: 5V.
- Microstep resolutions:Â full, 1/2, 1/4, 1/8, 1/16, and 1/32.
- Dimensions : 15 x 20 mm.
- Weight: 4 gm.
SKU: 52599 -
-
Stepper Motor Drivers
L298N Dual H Bridge DC/Stepper Motor Driver Controller Module
SKU: 51971- Driver chip: L298N Dual H Bridge
- Supply voltage: VMS 5V – 35V
- Peak current IO: 2A per bridge
- Max power consumption: 20W
- Provides 4 LEDs that reflect the state of the control logic
- Independent direction, speed, and braking for each motor
SKU: 51971 -
Stepper Motor Drivers
L9110 L9110S DC Stepper Motor Driver Board HBridge
SKU: 699567- Â Power supply voltage: DC2.5-12V
- Â Each channel has 800mA continuous current output
- Â Low saturation pressure drop
- Â TTL/CMOS output level compatible can be connected directly to the CPU
- Â Control and drive integrated into IC
- Â Have pin high-pressure protection function
SKU: 699567 -
-
Stepper Motor Drivers
LV8729 6V-36V Ultra Quiet 4-layer Substrate Stepper Motor Driver with Heatsink for 3D Printer
Stepper Motor DriversLV8729 6V-36V Ultra Quiet 4-layer Substrate Stepper Motor Driver with Heatsink for 3D Printer
SKU: 1302221. In 64 subdivision or 128 subdivision to achieve a better ultra-quiet effect.
2. Operating voltage: 6V-36V, the proposed voltage is 12V.
3. The maximum current is 1.5A, the default is 0.8A.
4. Segment: 1, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128.SKU: 130222 -
Stepper Motor Drivers
MACH3 Interface Board CNC 5 Axis with Optocoupler for Stepper Motor Driver and USB cable
Stepper Motor DriversMACH3 Interface Board CNC 5 Axis with Optocoupler for Stepper Motor Driver and USB cable
SKU: 18988- Compatible with MACH3, Linux CNC (EMC2) etc. parallel-control CNC software.
- USB power supply and peripherals power phase are separate to protect computer security.
- All the signals are to-isolate which can protect your computer security.
- 5-input interface to define the Limit, Emergence-Stop, Cutter alignment, etc.
- Wide input voltage range: 12-24V, and with anti-reverse function.
- One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
SKU: 18988 -
-
Stepper Motor Drivers
MKS SBASE V1.3 32-bit Open Source Smoothieboard
SKU: 766364- Â 32bit 100M Cortex-M3 MCU-LPC 1768
- High-performance
- Support highly modular open source firmware Smoothieware
- Easy for secondary development
- Â Support network function, then proceed remote control via IE Explorer.
SKU: 766364 -
Stepper Motor Drivers
MKS-LV8729-OC 1.5A Ultra Quiet Stepper Motor Driver for 3D Printers and CNC
SKU: 815856- High-speed optocoupler, high-speed without losing a step
- LV8729 chip, with over-current protection circuit, the maximum support 128 segments
- Automatic half-flow function
- A variety of input methods to meet a variety of interface needs
- The use of increased heat sink, good heat dissipation
SKU: 815856 -
-
-
Stepper Motor Drivers
TB6560 Driver Board 3A CNC Router Single 1 Axis Controller Stepper Motor
SKU: 18979- Driver Chip: TB6560AHQ
- Operating Voltage: 10-35V
- Nominal Voltage: 24V
- With the large heat sink to ensure good heat dissipation
- 6N137 high-speed OptoCoupler, to ensure a high speed without step out.
SKU: 18979 -
Stepper Motor Drivers
TB6600 0.2-5A CNC Controller Stepper Motor Driver Single Axes Two Phase Hybrid Stepper Motor for CNC
-7%Stepper Motor DriversTB6600 0.2-5A CNC Controller Stepper Motor Driver Single Axes Two Phase Hybrid Stepper Motor for CNC
SKU: 835839- Input Current: 1~5A
- Supply Voltage: 12 to 48VDC
- Output Current: 0.2~5.0A
- Power (MAX): 160W
- Temperature: -10～45℃
- H bridge bipolar constant current drive.
SKU: 835839 -
Stepper Motor Drivers
TB6600 Stepper Motor Driver Controller 4A 9~42V TTL 16 Micro-Step CNC 1 Axis
-15%Stepper Motor DriversTB6600 Stepper Motor Driver Controller 4A 9~42V TTL 16 Micro-Step CNC 1 Axis
SKU: 43211- Input Current: 0~5A
- Output Current: 0.5~4.0A
- Control Signal: 3.3~24V
- Power (MAX): 160W
- Micro Step: 1, 2/A, 2/B, 4, 8, 16, 32
- Temperature: -10～45℃
- H bridge bipolar constant current drive.
SKU: 43211 -
Stepper Motor Drivers
TB6600 Stepper Motor Driver Controller 8~50V 4.5A
SKU: 49111- Supply Voltage: 8V – 50V DC (36V recommended).
- Output current: 0.3A – 4.5A (peak value of 5A).
- Micro Step: 1, 2, 8, 16.
- Maximum PWM frequency:Â 200kHz.
- Adjustments for the maximum current of the LED: 1A, 2.2A, 3.3A, 4.5A.
- Operating temperature: -10 to + 45 ° С.
SKU: 49111 -
Stepper Motor Drivers
TL-Smoother Eight Chip Module DFORCE Vibration Pattern Filter with Cable
SKU: 766383- TL Smoother can effectively eliminate the mechanical chatter generated by 3D printer motors,
- The TL-Smoother is an addon module for 3D printer stepper motor drivers.
- The board provides flyback diodes for the motor outputs, so they are also protected against inductance voltages in the unpowered state of the driver.
- You will get smoother movement, especially on the delta-style 3D printer
- I3 and UM models can also be used, and different machines will have different clipping effects.
SKU: 766383 -
-
Stepper Motor Drivers
TMC2208 Stepper Motor Driver Module
SKU: 699623- Voltage range: 3.3-5V
- Maximum current: 1.2A per phase (continuous, with cooling), 2A peak per phase
- Works with 3.3V and 5V signals
- Comes with heatsink for better cooling
- Has StealthChop technology for quieter stepper motors
- Has SpreadCycl technology for smoother movements
SKU: 699623 -
Stepper Motor Drivers
TMC2209 Stepper Motor DriverF
SKU: 835841- Maximum current: 2A per phase (continuous, with cooling), 2.8A peak per phase
- Works with 3.3V and 5V signals
- Comes with heatsink for better cooling
- Has StealthChop technology for quieter stepper motors
- Has SpreadCycl technology for smoother movements
SKU: 835841 -
Stepper Motor Drivers
ULN2003 Driver Module Stepper Motor Driver
SKU: 28379- 5-12V power supply
- 4-way signal indicator
- Chip all the pins have Input leads Mounted for easy connection to use
- XH-5P socket can be connected directly 28BYJ-48 Model stepper motor
- Dimensions: 32 x 18 x 11mm (LxWxH)
- Weight: 3 gm
SKU: 28379 -
Stepper Motor Drivers
ULN2003 Driver Module Stepper Motor Driver Board
SKU: 312977- ULN2003A motor driver chip
- Chip all the pins already leads for easy connection to use
- 5-12V power supply
- 4-way signal indicator
- Step angle: 5.625 x 1 / 64
- Reduction ratio: 1 / 64
- Phase: 4
- Current / Phase: 5V
SKU: 312977 -
Stepper Motor Drivers
MA860H Digital Stepper Micro-Step CNC Motor Driver 50-110 VDC with 1.8-7.5A
SKU: 6747- Supply voltage up to 80VAC or +110VDC
- Output current up to 7.2A
- Pulse input frequency up to 300 KHz
- 16 selectable resolutions in decimal and binary, up to 51,200 steps/rev
- Suitable for 2-phase and 4-phase motors
- Dimensions: 118×75.5×34 (LxWxH) mm
SKU: 6747 -
Stepper Motor Drivers
Leadshine DM542 Digital Stepper Motor Driver
SKU: 6745- Good high-speed performance
- Supply voltage up to +50VDC
- Output current up to 4.2A
- Pulse frequency up to 300 KHz
- Automatic idle-current reduction
- 3-state current control technology
- Self-adjustment technology
- Pure-sinusoidal current control technology
SKU: 6745 -
-
Stepper Motor Drivers
DRV8825 Stepper Motor Driver with Aluminum Heat Sink
SKU: 6721- Supply Voltage: 8.2 – 42 VDC.
- Current Capacity : 2.2A max(24V).
- Continuous current per phase: 1.5 A.
- Minimum Logic voltage: 2.5V.
- Maximum Logic Voltage: 5V.
- Microstep resolutions:Â full, 1/2, 1/4, 1/8, 1/16, and 1/32.
- Dimensions : 15 x 20 mm.
- Weight: 4 gm.
SKU: 6721
