Flight Controller & Accessories
Buy a diverse range of Quadcopter Flight Controller on Robu. Our quality flight controllers are affordable & necessity for any drone enthusiast. The number of flight controller for FPV drone can be overwhelming for beginners. Choosing a FC is a tedious task, let leave it up to us and enjoy your flight. Our main intend is always to provide rapidly evolving becoming smaller, with more features integrated, and using better processors and hardware.
The FC is the brain of the aircraft. It’s a circuit board with a range of sensors that detect movement of the drone, as well as user commands. Using this data, it then controls the speed of the motors to make the craft move as instructed.
-
KK2.1.5 Multi-rotor LCD Flight Control Board With 6050MPU And Atmel 644PA
₹ 1,649.00(inc GST)
₹ 1397.46 (+18% GST extra)
- IC: Atmega644 PA
- GYRO/ACC.: 6050MPU InvenSense Inc.
- INPUT VOLTAGE: 4.8V-6.0V.
- AVR INTERFACE: Standard 6 Pin.
- SIGNAL FROM RECEIVER: 1520us(5 channels).
- SIGNAL TO ESC: 1520us.
-
SP Racing F3 Flight Controller Integrate OSD ACRO Version
₹ 2,590.00(inc GST)
₹ 2194.92 (+18% GST extra)
- STM32F303 CPU, 72Mhz inc FPU
- CPU: STM32F303, 72Mhz inc FPU
- Acro: High-Capacity Flash
- Accelerometer/gyro: MPU6050
- Board size: 36 x 36 x 5mm (without shell)
- Board weight: 5.9g
- Weight: 22 gm(with all accessories)
-
SP Racing F3 Flight Controller Deluxe
₹ 2,590.00(inc GST)
₹ 2194.92 (+18% GST extra)
-  Stackable design – perfect for integrating with OSDs and power distribution boards.
- 16 PWM I/O lines for ESCs, Servos and legacy receivers. 8 available on standard pin headers. 8 via side mounted connectors.
- Full support for OneShot ESCs for easy PID tuning and a sharper response.
- Supports SBus, SumH, SumD, Spektrum1024/2048, XBus, PPM, PWM receivers.
- No external inverters required (built-in).
- Dedicated output for programmable LEDs – great for orientation, racing and night flying.
- Dedicated I2C port for connection of OLED display without needing flight battery.
- Battery monitoring ports for voltage and current.
- Sonar support for precision low-altitude hold.
- Buzzer port for audible warnings and notifications.
- Symmetrical design for a super tidy wiring.
- Barometer mounted on the bottom of the board for easy wind isolation.
- Â Wire up using pin headers, JST-SH sockets or solder pads. Use either right-angled or straight pin-headers.
-
SP Racing F3 Flight Controller ACRO Version
₹ 1,190.00(inc GST)
₹ 1008.47 (+18% GST extra)
- The STM32F3 CPU, MPU 6050 sensor, 16M high-capacity flash memory, OSD function.
- The SP F3 runs Cleanflight which can be configured to suit your needs using a cross-platform GUI (Windows/OSX/Linux).
- Tiny and lightweight, the Racing F3 has a standard 36x36mm form-factor with 30.5mm mounting holes and weighs just 6 grams.
- Flight Logging, on-board high-capacity black box flight log recorder – optimize your tuning and see the results of your setup without guesswork.
- OneShot ESC, full support for OneShot ESCs for easy PID tuning and a sharper response.
- Broad RC receiver supports SBus, SumH, SumD, Spektrum1024/2048, XBus, PPM, PWM receivers, no external inverters required (built-in).
-
SP RACING F3 FC Replacement Accessories Set
₹ 190.00(inc GST)
₹ 161.02 (+18% GST extra)
Accessories compatible with SP RACING F3 Flight Controller Module
High-quality cable and connectors.
1 x 3*8 Burg connector(Straight)
1 x 3*8 Burg connector(Right-angle)
1 x 1*10 Burg Connector(Straight)
2 x 2pt cable
2 x 4pt cable
2 x 8pt cable -
Pixhawk PX4 2.4.7 32Bits Flight Controller for Quadcopter Multicopter
₹ 14,880.00(inc GST)
₹ 12610.17 (+18% GST extra)
- 168 MHz / 252 MIPS Cortex-M4F.
- Abundant connectivity options for additional peripherals (UART, I2C, CAN).
- Integrated backup system for in-flight recovery.
- Redundant power supply inputs and automatic failover.
- External safety switch.
- Multicolor LED main visual indicator.
-
Pixhawk I2C Port Expand Board with Cable
₹ 199.00(inc GST)
₹ 168.64 (+18% GST extra)
- Package Weight: 5 gmÂ
- Number of Ports: 5.
- Board Dimensions: 33 x 12 x 6 mm(LxWxH)
- Net Weight: 3g
- Brand new and high quality
- The I2C splitter expands the I2C port to allow up to four additional peripherals to connect to Pixhawk.
-
Pixhawk 2.4.8 Drone Flight Controller PX4 32 Bit Autopilot – Good Quality
₹ 5,950.00(inc GST)
₹ 5042.37 (+18% GST extra)
- Supply Voltage: 7V.
- Processor: 32 Bit Cortex M4 Core
- Bus interface (UART, I2C, SPI, CAN).
- Firmware: Mission planner.
- Sensors: Gyrometer, Accelerometer, Barometer & Magnetometer
- Micro SD card to record flight data.
-
OpenPilot CC3D EVO Flight Controller with Side Pins
₹ 1,090.00(inc GST)
₹ 923.73 (+18% GST extra)
- Powerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and 20KB RAM.
- 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer.
- Tiny 36 x 36 mm 4 layer PCB for superior electrical noise reduction and flight performance.
- Software support for Windows, Mac, and Linux.
- Direct high-speed USB support with no drivers required, a true plug and play device.
- Spektrum satellite receiver support.
- Futaba S-BUS hardware support.
-
OpenPilot CC3D EVO Flight Controller Straight Pin
₹ 1,249.00(inc GST)
₹ 1058.47 (+18% GST extra)
- 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer.
- Tiny 36 x 36 mm 4 layer PCB for superior electrical noise reduction and flight performance.
- Software support for Windows, Mac, and Linux.
- Direct high-speed USB support with no drivers required, a true plug and play device.
- Spektrum satellite receiver support.
- Futaba S-BUS hardware support.
- Innovative Flexi-port technology for superior port flexibility.
- 4Mbits onboard EEPROM for configuration storage.
-
OMNIBUS F4 V2 PRO Flight Controller with SD Card Slot & BEC
₹ 2,690.00(inc GST)
₹ 2279.66 (+18% GST extra)
- Dimensions: 37 x 37 x 10 mm(L x H x W)
- Weight: 12 gm.
- SPI Gyro MPU6000
- MicroSD Blackbox
- F4 Processor (F405)
- 5v3a SBEC
- Built-in Current Sensor
- On-Board OSD (controlled by Beta flight, FC over SPI bus)
- On-Board Video Filter (only can supply 5V to VTX and Camera)
- On-Board Voltage Regulator and Power supply (BEC)
-
Omnibus F4 V2 PRO Flight Controller with Built-in OSD
₹ 1,990.00(inc GST)
₹ 1686.44 (+18% GST extra)
- STM32 F405 MCU
- Runs Beta flight (3.0.1 and up)
- Race light and D-ronin firmware
- SBUS/PPM input (Pinheaders)
- 6PWM output (1-4Pinheaders and Sh1.0 Plug, 5-6 as Pinheaders)
- Only 36x36mm, mount holes 30.5Ă—30.5mm
- SPI Sensor MPU6000
- 128Mbit Flash
-
Naze32 6DOF Flight Control board
₹ 1,090.00(inc GST)
₹ 923.73 (+18% GST extra)
- Battery voltage monitoring.
- Built-in FrSky telemetry converter.
- Modern 32-bit processor (STM32 F103) running at 3.3V/72MHz.
- Onboard USB for setup and configuration.
- Modern GUI for all operating systems, Baseflight Configurator.
Â
-
Naze32 10DOF Flight Control Board
₹ 1,615.00(inc GST)
₹ 1368.64 (+18% GST extra)
- Axis: 2000 degrees/second 3-axis MEMS gyro.
- Input voltage: Max 16V on input rail and up to 35V 6s on the voltage sense line.
- Built-in FrSky telemetry inverter (shared w/main port).
- A modern 32-bit processor running at 3.3V/72MHz (STM32F103CB).
- Onboard MicroUSB for setup and configuration.
- Multi WiFi-based configuration software for easy setup.
-
Mini USB (90° Connector) to FPV AV Output Cable for GoPro Hero 3
₹ 199.00(inc GST)
₹ 168.64 (+18% GST extra)
- USB connector is used to connect to the USB port on your GoPro Hero3 Camera.
- The 3 pin female connector is for AV video output
Typical application:
Video output from your GoPro Hero 3 USB port to your video wireless transmitter. (Connect your GoPro Hero 3 directly to FPV transmitter)
-
Mini OSD for Pixhawk Flight Controller
₹ 990.00(inc GST)
₹ 838.98 (+18% GST extra)
- ATmega328P with Arduino bootloader
- MAX7456 monochrome on-screen display
- FTDI cable compatible pinout
- Standard 6 pin ISP header
- 2 independent power sections with an LED indicator on each
- Solder jumpers for combining the power sections
Compatible flight controller:
APM2.5/2.6/2.8
Pixhawk PX4 -
Micro Minim OSD For Racing F3 Naze32 Flight Controller RC Drone
₹ 649.00(inc GST)
₹ 550 (+18% GST extra)
- ATmega328P with Arduino bootloader.
- MAX7456 monochrome on-screen display.
- +5V 500mA regulator for up to +12V supply input.
- FTDI cable compatible pinout.
- The standard 6-pin ISP header.
- Standalone, or with APM/ Flip / Flip32+ flight controllers.
-
Holybro Original Pixhawk PX4 Flight Controller (without GPS)
₹ 17,369.00(inc GST)
₹ 14719.49 (+18% GST extra)
- Main FMU Processor: STM32F76
- 32 bit ARM® Cortex® M7, 216 MHz Processor running NuttX RTOS,
- More computing power and 2X the RAM than previous versions)
- Abundant connectivity options for additional peripherals (UART, I2C, CAN)
- Redundant power supply inputs and automatic failover
- External safety button for easy motor activation
- New sensors with higher temperature stability
- Multicolor LED indicator
- Integrated vibrations isolation
- High-power, multi-tone piezo audio indicator
- microSD card for long-time high-rate logging
-
Flip32 OMNIBUS F4 Flight Controller
₹ 1,499.00(inc GST)
₹ 1270.34 (+18% GST extra)
- 128Mb Flash(16M Byte)
- SBUS/PPM input (Pinheaders)
- DSM/DSM2/DSMX input(Plug)
- 6PWM output (Pinheaders)
- Only 36x36mm, mount holes 30.5Ă—30.5mm
- All through hole pin header Design  -no Sh connectors
- STM32 F405 MCU, Runs Raceflight CC3D REVO firmware
- Works Perfect with Raceflight or BetaFlight 3.0
-
F3 EVO V2.0 Flight Control
₹ 1,686.00(inc GST)
- Supported Receiver Input Signal: PPM, SBUS, DSM
- Support PPM, SBUS, DSM receiver input signal
- Battery voltage detection and buzzer interface
- Large current NMOS transistors, operating current can reach 10A or higher
- Use STM32F303CCT6 + MPU6500, advanced hardware platform F3 for higher flight stability
-
F3 Brushed Flight Control Board Based On SP RACING F3 EVO Brush for Micro FPV Frame
₹ 1,090.00(inc GST)
₹ 923.73 (+18% GST extra)
- Supported Receiver Input Signal: PPM, SBUS, DSM
- Support PPM, SBUS, DSM receiver input signal
- Battery voltage detection and buzzer interface
- Run on SP RACING F3 EVO firmware 32 brush flight control
- Large current NMOS transistors, operating current can reach 10A or higher
- Use STM32F303CCT6 + MPU6500, advanced hardware platform F3 for higher flight stability
-
DJI NAZA-M Lite V1.1 with GPS Kit
₹ 10,510.00(inc GST)
₹ 8906.78 (+18% GST extra)
- Supported Multi-Rotor: Quad-rotor I4, X4 / Hex-rotor I6, X6, IY6, Y6.
- Supported ESC Output: 400Hz refresh frequency.
- Recommended Transmitter: PCM or 2.4GHz with minimum 4 channels.
- Power Consumption: MAX1. 5W (0.3A@5V) Normal:0.6W (0.12A@5V).
- Weight: MC:25g; VU:20g; GPS:21.3g.
- All-in-One Design.
- Advanced attitude stabilized Algorithm.
- Multiple flight control mode/intelligent switching.
- GPS Module Available/Accurate Position hold.
- Intelligent Orientation Control (IOC).
- Failsafe mode.
-
DJI NAZA M V2 Multirotor Autopilot Controller set with GPS
₹ 22,499.00(inc GST)
₹ 19066.95 (+18% GST extra)
- Input Voltage (V): MC: 4.8V~5.5V (recommended 2S~6S Lipoly).
- Supported ESC Output 400 Hz refresh frequency
- Supported Transmitters PCM or 2.4 GHz radio with at least 4 channels
- Power Consumption MAX: 1.5 W (0.3 A at 5 V)
- Operating Temperature: -10 to 50°C
-
DJI Naza M Lite Multi-Rotor Flight Controller without GPS
₹ 6,661.00(inc GST)
₹ 5644.92 (+18% GST extra)
- Input Voltage (V): MC: 4.8V~5.5V (recommended 2S~6S Lipoly).
- Power Consumption: MAX: 1.5W (0.3A @ 5V), Normal: 0.6W (0.12A @ 5V).
- Operating Temperature:-10°C ~ +50°C.
- Supported ESC Output: 400Hz refresh frequency
-
DF13 6 Pin Flight Controller Cable
₹ 89.00(inc GST)
₹ 75.42 (+18% GST extra)
- Item Name: DF13 6 Pin Flight Controller Cable
- 100% Brand new and high quality.
- Weight: about 3g
- Plug Type: DF 13 6 pin
- Length: 200mm(26AWG).
- Color: Red, and Black
- Useful for connection between the PixHawk and the GPS receiver module. or many receiver connections.
-
DF13 4 Pin Flight Controller Cable
₹ 49.00(inc GST)
₹ 41.53 (+18% GST extra)
- Item Name: DF13 4 Pin Flight Controller Cable
- 100% Brand new and high quality.
- Weight: about 3g
- Plug Type: DF 13 4 pin
- Length: 200mm(26AWG).
- Color: Red, and Black
- Useful for connection between the PixHawk and the GPS receiver module. or many receiver connections.
-
APM 2.8 Flight Controller with Built-in Compass
₹ 2,425.00(inc GST)
₹ 2055.08 (+18% GST extra)
- Model: APM 2.8
- Input Voltage (V): 12-16 V.
- Processor: ATMEGA2560 and ATMEGA32U-2
- Dimensions (mm) LxWxH: 70 x 45 x 15.
- Micro SD card slot: No.
- Sensors: 3-Axis Gyrometer
Accelerometer
High-performance Barometer
-
AeroFC Flight Controller Board
₹ 30,090.00₹ 25,275.00(inc GST)
You save(16%): ₹ 4,815.00
- High-Speed STM32 processor
- Triple Redundant IMU
- Light Weight
- Isolated & Dampened IMU
- Compatible with Ardupilot and PX4.
- It can be configured with AeroGCS, Mission Planner, QGround Control software, etc.
Limited Time Launch Offer !!!
-
 Anti-Vibration Fixed Screws 4pcs
₹ 112.00(inc GST)
- Length: 7mm rubber/ 4.5mm screw length
- Installation groove diameter: diameter of 2.9 mm
- Anti-vibration screws are the best way to soft mount your flight controller.
- Flight controller anti-vibration screws are easy to install, perfect fit, and significant vibration elimination.