Here you can get High-quality Voltage and Current sensor module With measuring range 5A to 60A. A current sensor is a device that detects electric current in a wire and generates a signal proportional to that current. The generated signal could be analog voltage or current or even a digital output.
Voltage sensors can determine both the AC voltage or DC voltage level. The input of this sensor can be the voltage whereas the output is the switches, analog voltage signal, a current signal, an audible signal, etc.
Current and Voltage
Showing all 17 results
-
Current and Voltage
20A Range Current Sensor Module ACS712
SKU: 23911- Low-noise analog signal path
- Device bandwidth is set via the new FILTER pin
- 5 µs output rise time in response to step input current
- Small footprint, low-profile SOIC8 package
- 2.1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8
- Supply Voltage: 4.5V~5.5V DC
- Measure Current Range: 20A
- Sensitivity: 100mV/A
SKU: 23911 -
Current and Voltage
30A range Current Sensor Module ACS712
SKU: 12264- Low-noise analog signal path
- Device bandwidth is set via the new FILTER pin
- 5 µs output rise time in response to step input current
- Small footprint, low-profile SOIC8 package
- 2.1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8
- Supply Voltage: 4.5V~5.5V DC
- Measure Current Range: 30A
- Sensitivity: 100mV/A
SKU: 12264 -
Current and Voltage
5A 12V Overcurrent Protection AC Current Detection Sensor Module
SKU: 400224LC 5A Over-current protection Sensor module uses a current transformer to collect the AC signal to achieve the relay over-current signal output within 0-5A. Relay pull while over-current, relay released while not over-current
SKU: 400224 -
Current and Voltage
5A range Current Sensor Module ACS712
SKU: 23910- Low-noise analog signal path.
- Device bandwidth is set via the new FILTER pin.
- 5 µs output rise time in response to step input current.
- Small footprint, low-profile SOIC8 package.
- 2.1 kV RMS minimum isolation voltage from pins 1-4 to pins 5-8.
SKU: 23910 -
Current and Voltage
5A range of single-phase AC current sensor module
SKU: 28369- Onboard precision microcurrent transformer.
- Onboard sampling resistor.
- The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA.
- Rated input current: 5A
- Rated output current: 5mA
- Change: 1000: 1
- The linear range: 0 ~ 10A (100 ohms)
- Linearity: 0.2%
SKU: 28369 -
Current and Voltage
ACS712 20A Current Sensor IC (ACS712ELCTR-20A-T)
SKU: 618488- 80 kHz bandwidth.
- Total output error 1.5% at TA = 25°C.
- Small footprint, low-profile SOIC8 package.
- 1.2 mΩ internal conductor resistance.
- 2.1 kV RMS minimum isolation voltage from pins 1-4 to pins 5-8.
- 5.0 V, single-supply operation.
- 66 to 185 mV/A output sensitivity.
SKU: 618488 -
Current and Voltage, Hall Sensor
ACS758LCB-050B Hall-Effect-Based Linear Current Sensor IC
SKU: 559742- Integrated shield greatly reduces capacitive coupling from the current conductor to die due to high dV/dt signals, and prevents offset drift in high-side, high-voltage applications.
- Total output error improvement through gain and offset trim over temperature.
- Small package size, with easy mounting capability.
- Monolithic Hall IC for high reliability.
- Output voltage proportional to AC or DC currents.
- Factory-trimmed for accuracy.
- Extremely stable output offset voltage.
- Nearly zero magnetic hystereses.
SKU: 559742 -
Current and Voltage
CJMCU-219 INA219 I2C Interface No Drift Bi-directional Current / Power Supply Monitoring Module
Current and VoltageCJMCU-219 INA219 I2C Interface No Drift Bi-directional Current / Power Supply Monitoring Module
SKU: 421237- 0.1 ohm 1% 2W current sense resistor
- Up to +26V target voltage
- Up to ±3.2A current measurement, with ±0.8mA resolution
- Senses Bus Voltages from 0 to 26 V
- 2C- or SMBus-compatible interface. The
- Reports Current, Voltage, and Power.
SKU: 421237 -
Current and Voltage
SCT 013 000 100A Non-Invasive AC Current Sensor Split Core Type Clamp Meter Sensor
Current and VoltageSCT 013 000 100A Non-Invasive AC Current Sensor Split Core Type Clamp Meter Sensor
SKU: 43399- Input Current : 100A
- Frequency: 50HZ-150KHZ
- Opening Size: 13 x 13mm/ 0.5″ x 0.5″(L*W)
- Output Plug 3.5mm
- Dielectric Strength 6000V AC/1min
- Suitable for lighting equipment, AC motors, air compressors, monitoring, current measurement, and protection
- Meet UL94-V0 flame retardant properties
SKU: 43399 -
-
Current and Voltage
SCT-013-030 Non-invasive AC Current Sensor Clamp Sensor 30A
SKU: 28668- Input Current : 0-30A
- Output Mode: 0-1V @ 30mA
- Frequency: 50HZ-150KHZ
- Opening Size: 13 x 13mm/ 0.5″ x 0.5″(L*W)
- Output Plug 3.5mm
- Dielectric Strength 6000V AC/1min
- Suitable for lighting equipment, AC motors, air compressors, monitoring, current measurement, and protection
- Meet UL94-V0 flame retardant properties
SKU: 28668 -
Current and Voltage
SCT-013-060 Non-invasive AC Current Sensor Clamp Sensor 60A
SKU: 618494- Input current (RMS): 60A.
- Max current: 75A.
- Work temperature: -25℃～+70℃.
- Storage temperature: -30℃～+90℃.
- Work voltage: 660V.
- Frequency range: 50Hz-1KHz.
- Dielectric strength: 3.5KV 50Hz 1min
SKU: 618494 -
Current and Voltage
SparkFun Current Sensor Breakout – ACS723
SKU: 637309- Analog output with bandwidth adjustable to 80kHz.
- Measures DC and AC currents up to 10 mA ~ 5A.
- Full electrical isolation of measured and sensed circuits.
- The version without the op-amp has a base sensitivity of 400mV/A.
SKU: 637309 -
Current and Voltage
Voltage Detection Sensor Module 25V
SKU: 29802- You can also use the IICLCD1602 LCD to display voltage.
- By 3P connector, connect this module with the expansion of board Arduino
- Voltage input range: DC 0-25 V
- Voltage detection range: DC 0.02445 VÂ to 25 V
- Voltage analog resolution : 0.00489 V
SKU: 29802 -
