Arduino Shield
-
Cytron Arduino PS2 Shield
₹ 1,349.00(inc GST)
₹ 1143.22 (+18% GST extra)
- 5V powered low current consumption.
- Simple to use UART protocol
- Vibrator motor on PS2 is controllable.
- Wired and Wireless PS2 controller is supported.
- PS2 Controller will automatically operate in analog mode.
- A status LED
- Jumper selector to select different UART Baud Rate (9600, 57600, 115200).
- Jumper selectors to select different digital pin as UART TX and RX pin.
-
10A Motor Driver Shield – MD10
₹ 1,564.00(inc GST)
₹ 1325.42 (+18% GST extra)
- Bi-directional control of 1 brushed DC motor.
- Support motor voltage ranges from 7V to 25V, .
- Maximum current up to 10A continuous and 15A peak (10 seconds).
- Solid state components provide faster response time and eliminate the wear and tear of a mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
- Speed control PWM frequency up to 10KHz.
- Selectable digital pins for PWM and DIR.
-
XD-216 Screw shield Screw Shield V1 Expansion Board
₹ 446.00(inc GST)
₹ 377.97 (+18% GST extra)
- Size: 29 x 71 mm
- Combines the function of Arduino Screw Shield and Sensor Shield.
- Expand all of IO interfaces from Arduino.
- 3-Pin male headers for easy sensor/servo connection.
- The Screw terminal can be screwed directly to the terminal on the thread and is reliable and convenient.
-
XBee Shield V03 Module Wireless Control
₹ 350.00(inc GST)
₹ 296.61 (+18% GST extra)
- Stackable design, easy to plug into the ARDUINO development board.
- Coupled with the Arduino Bluetooth Bee Bluetooth module, and other Bluetooth devices can communicate Wirelessly.
- 3.3v and 5v dual power output.
- 3.3v and 5v IO compatible.
- USB2.0 protocol.
-
XBee IO Expansion Shield – XBEE 2
₹ 1,153.00(inc GST)
- Expand 14 digital IO interface (12 steering gear interface)and power
- Six analog IO interfaces and power
- One digital port interface for external power supply terminals
- Digital port external power supply and on-board electrical automatic switch
- One external power input terminals and one input needle
- RS485 interface (D0-RX, D1-TX, D2-EN)
- IIC/the I2C/TWI interface (A4-SDA, A5-SCL)
- SD card module interface
-
UNO Proto Shield prototype expansion board with SYB-170 mini breadboard
₹ 194.00(inc GST)
₹ 164.41 (+18% GST extra)
- It has a nice standard 0.1″x0.1″ prototyping grid with big pads
- Comes with Stacking headers and plain header, choose whichever you want when soldering together
- An IC pattern for adding DIP ICs up to 20 pins
- Power rails down the middle and sides
- A reset button and an extra general use button
- Two 3mm general use LEDs, red and green, as well as 2 matching resistors
-
Servo Driver Module Shield 16 Channel
₹ 550.00(inc GST)
₹ 466.1 (+18% GST extra)
- The I2C input, PWM output control 16 roads, steering gear can 16 roads.
- The steering gear power independent V + input maximum 6 V.
- Logic signals and logical power independent output for 3V to 5 V.
- 40-1000 Hz frequency.
- Terminal block for power input.
- Reverse polarity protection on the terminal block input
- Green power-good LED
-
Sensor Shield V5 Expansion Board For Arduino
₹ 199.00(inc GST)
₹ 168.64 (+18% GST extra)
- Retain the merits of the V4.0 version
- Laminated design
- PCB immersion gold processing technology
- IIC interface
- Bluetooth module communication interface
- SD card module communication interface
- APC220 wireless rf modules communication interface
- RB URF v1.1 ultrasonic sensors interface
- 12864 LCD string of line and parallel interface
- 32 servo controller interface
-
Prototype Shield V3.0 For Arduino Mega with breadboard
₹ 313.00(inc GST)
₹ 265.25 (+18% GST extra)
- The shield can support being fully assembled with Arduino MEGA
- Support soldering components directly on this shield
- Support sticking the mini breadboards on this shield
- Reset button up top
- Mainboard aureate quadrate
- With SOP28 SMT components encapsulation
-
Proto Screw Shield 1.0 For Arduino Uno
₹ 359.00(inc GST)
₹ 304.24 (+18% GST extra)
- Arduino terminal to provide the IO, port connection.
- 3.81 posts quality, reliable, convenient, durable.
- Combined with the Proto Shield, the middle can be used as a prototype expansion board.
- Double-sided PCB Prototyping extended area vias connecting the front sides can be welded components.
- The middle section can be placed small bread plate, convenient test extend
-
NANO IO Shield Expansion Board For Arduino Screw Terminals
₹ 249.00(inc GST)
₹ 211.02 (+18% GST extra)
- Compatible with Arduino NANO
- All digital and analog pins breakout
- Compact size.
- Leads all pins out, convenient for wiring and doing experiments.
- Dimensions: 53 x 36 x 12 (LxWxH) mm.
- Weight: 22 gm.
-
Nano IO Expansion Shield for Arduino NANO 328P
₹ 290.00(inc GST)
₹ 245.76 (+18% GST extra)
- All digital and analog pins breakout
- XBee and nRF24L01+ module interface
- External power supply current support
- Compatible pin map for electronic brick
- Output Voltage-3.3V
- 7-12V external power supply.
-
LoRa Shield for Arduino V95
₹ 2,499.00(inc GST)
₹ 2117.8 (+18% GST extra)
- Compatible with 3.3v or 5v I/O Arduino Board.
- Frequency Band: 915MHz/868 MHZ/433 MHZ (Pre-configure in a factory)
- Low power consumption
- Compatible with Arduino Leonardo, Uno, Mega, DUE
- External Antenna via I-Pex connector
-
L293D Motor Driver/Servo Shield for Arduino
₹ 179.00(inc GST)
₹ 151.69 (+18% GST extra)
- 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
- 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes.
- Can run motors on 4.5VDC to 25VDC.
- Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, or interleaved stepping.
-
Data Logger module Logging Shield data Recorder Shield
₹ 290.00(inc GST)
₹ 245.76 (+18% GST extra)
- SD card interface works with FAT16 or FAT32 formatted cards. 3.3v level shifter circuitry prevents damage to your SD card.
- Real-time clock (RTC) keeps the time going even when the Arduino is unplugged. The battery backup lasts for years.
- Included libraries and example code for both SD and RTC mean you can get going quickly Prototyping area for soldering connectors, circuitry or sensors.
- The onboard 3.3v regulator is both a reliable reference voltage and also reliably runs SD cards that require a lot of power to run.
- A dedicated and well-designed data logging shield for Arduino.
-
Cytron XBee Shield
₹ 681.00(inc GST)
₹ 577.12 (+18% GST extra)
-
Mounts directly onto your Arduino
-
DIN and DOUT pins of XBee can be connected to either the USB’s UART pins or another digital pin on the Arduino (D0, D1, D2, D3, D8, D9, D10, D11)
-
3.3V power regulation and proper level shifting on-board communication between 5V and 3.3V
-
Extra 0.1″ spaced prototyping holes
-
Reset button brought out to shield
-
Power, DIN, DOUT, RSSI, and DIO5 indicator LEDs
-
-
Cytron LCD keypad Shield High Quality
₹ 619.00(inc GST)
₹ 524.58 (+18% GST extra)
- Provides a user-friendly interface that allows users to go through the menu, make selections etc.
- It consists of a 1602 white character blue backlight LCD.
- The keypad consists of 6 keys select, up, right, down, left and reset.
- To save the digital IO pins, the keypad interface only uses one ADC channel.
- The key value is read out through a 5 stage voltage divider.
-
Cytron 2Amp Motor Driver Shield
₹ 829.00(inc GST)
₹ 702.54 (+18% GST extra)
-
Logic control, 5V from Arduino main board
-
Polarity protection for External motor power input
-
2 fast test buttons for each motor channel
-
Motor Driven Voltage:6.5 to 12VDC(VIN Power Supply), 5.0 to 26VDC (External Power Source)
-
Up to 2A current each channel
-
Pin 4, 5,6,7 are used to drive two DC motor
-
Support PWM speed control
-
Support advance speed control
-
-
1602 LCD Board Keypad Shield Blue Backlight
₹ 225.00(inc GST)
₹ 190.68 (+18% GST extra)
- Provides a user-friendly interface that allows users to go through the menu, make selections etc.
- It consists of a 1602 white character blue backlight LCD.
- The keypad consists of 6 keys select, up, right, down, left and reset.
- To save the digital IO pins, the keypad interface only uses one ADC channel.
- The key value is read out through a 5 stage voltage divider.