Categories

Motor Driver

View cart “10A Motor Driver Shield – MD10” has been added to your cart.
  • 16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi

    SKU: 43740
     350.00

    (inc GST)

    ₹ 296.61 (+18% GST extra)

    1. Adjustable frequency PWM up to about 1.6 KHz
    2. 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
    3. Configurable push-pull or an open-drain output
    4. The output enable pin to quickly disable all the outputs
    5. Terminal block for power input
    6. Reverse polarity protection on the terminal block input
    7. Green power-good LED
    Add to cart
  • 20A PWM DC Motor Speed Regulator Module (9V, 12V, 24V, 36V, 48V, 60V)

    SKU: 51649
     590.00

    (inc GST)

    ₹ 500 (+18% GST extra)

    1. Adjustable speed range: 0%-100%.
    2. Speed adjustment way: Potentiometer.
    3. Output voltage: Linear under load.
    4. Speed control type: Basins.
    5. Output voltage: Load Linear
    6. Type: Adjusting flow
    7. The motor running condition adjustment: Forward  / Stop / Reverse
    Add to cart
  • 5-36v Switch Drive High-power MOSFET Trigger Module

    SKU: 52812
     150.00

    (inc GST)

    ₹ 127.12 (+18% GST extra)

    This 5-36v Switch Drive High-power MOSFET Trigger Module can control the output of power equipment, motors, light bulbs, LED lights, DC motors, micro-pumps,  solenoid valves, PWM, motor speed control, lamp brightness. etc.

    Add to cart
  • A3967 Stepper Motor Driver For Arduino

    SKU: 43823
     199.00

    (inc GST)

    ₹ 168.64 (+18% GST extra)

    1. Power supply: 7V to 30V.
    2. The higher the voltage, the higher the torque at high speeds.
    3. Adjustable current control from 150mA/phase to 750mA/phase.
    4. Logic voltage: 5V or 3.3V.
    5. A3967 microstepping driver.
    Add to cart
  • A4988 driver Stepper Motor Driver- Normal Quality

    SKU: 52807
     139.00

    (inc GST)

    ₹ 117.8 (+18% GST extra)

    1. Supply Voltage : 8-35 VDC.
    2. Current : 1.0A  (no heatsink ).
    3. Current : 2.0A (with heat-sinking).
    4. logic input : 3 – 5.5V .
    5. Automatic current decay mode detection / choice.
    6. Mixed with slow current decay mode.
    Add to cart
  • CNC shield V3 for Engraving Machine 3D Printer A4988 DRV8825 driver expansion board

    SKU: 12202
     190.00

    (inc GST)

    ₹ 161.02 (+18% GST extra)

    1. Latest Arduino CNC Shield Version 3.10
    2. GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
    3. Coolant enable
    4. Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
    5. Compact design.
    6. 4-Axis support (X, Y, Z, A-Can duplicate X, Y, Z or do a full 4th axis with custom firmware using pins D12 and D13)
    7. 2 x End stops for each axis (6 in total)
    Add to cart
  • CNC Three Axis Stepper Motor Drive Controller Motherboard compatible with Arduino

    SKU: 51543
     990.00

    (inc GST)

    ₹ 838.98 (+18% GST extra)

    1. Model: LBA-B-V4.
    2. Axis: XYZ Three Axis.
    3. Power Supply: 12V.
    4. Dimension: 120 x 65 mm.
    5. Pitch size: 112 x 57 mm.
    6. Laser Power: 100mW to 5W.
    7. Stepper Motor Power: Max 2A.
    Add to cart
  • Cytron 2Amp Motor Driver Shield

    SKU: 16014
     829.00

    (inc GST)

    ₹ 702.54 (+18% GST extra)

    1. Logic control, 5V from Arduino main board
    2. Polarity protection for External motor power input
    3. 2 fast test buttons for each motor channel
    4. Motor Driven Voltage:6.5 to 12VDC(VIN Power Supply), 5.0 to 26VDC (External Power Source)
    5. Up to 2A current each channel
    6. Pin 4, 5,6,7 are used to drive two DC motor
    7. Support PWM speed control
    8. Support  advance speed control
    Add to cart
  • Cytron Dual channel 10A Motor Driver UNO Robot Controller

    SKU: 49866
     2,510.00

    (inc GST)

    ₹ 2127.12 (+18% GST extra)

    1. Onboard 1A (maximum) 5V voltage regulator.
    2. Onboard 500mA (maximum) 3.3V voltage regulator.
    3. 0-5V digital outputs with 3.3V compatible inputs.
    4. 14 Digital I/O Pins (6 PWM outputs).(4 pin used for Motor driver)
    5. 6 Analog Inputs (Can be digital I/O too).
    6. Maximum current up to 10A continuous and 30A Peak.
    7. ISP 6-pin Header.
    8. 32k Flash Memory.
    9. 16MHz Clock Speed.
    10. R3 Shield Compatible.
    Add to cart
  • Cytron FD04A 4-Channel Motor Driver

    SKU: 16010
     2,362.00

    (inc GST)

    ₹ 2001.69 (+18% GST extra)

    1. Industrial grade PCB.
    2. Vmotor: 7 V to 25 V DC.
    3. Each component is soldered properly and tested.
    4. Able to drive 4 DC motor at 2.5A (peak), 1.5A continuously.
    5. 2 LEDs as a direction indicator for each motor.
    6. 1 LED as a power indicator.
    7. A pluggable connector for more user-friendly design.
    8. Fully compatible with Cytron DIY project, Flexibot – Using Transwheel (PR19).
    Add to cart
  • Cytron SmartDriveDuo-60 MDDS60 60A (100A peak)

    SKU: 8014
     12,064.00

    (inc GST)

    ₹ 10223.73 (+18% GST extra)

    1. DC Brush motor Driver, not for brushless motor
    2. Input Voltage (Motor): 7 – 45VDC
    3. Two manual/test buttons for each channel.
    4. Two output indicator LEDs for each channel.
    5. Suitable for combat or sumo robot.
    6. Battery Low Voltage Monitoring Mode
    Add to cart
  • DC Motor PWM Speed Regulator 1.8V, 3V, 5V, 6V, 12V-2A speed control switch function

    SKU: 12267
     240.00

    (inc GST)

    ₹ 203.39 (+18% GST extra)

    1. Input supply voltage: 1.8V- 15V DC.
    2. The maximum output power: 30W
    3. Output current : 2A(Max).
    4. With resettable fuse.
    5. Equipped with LED indicator.
    6. Potentiometer with switch function for PWM adjustment.
    Add to cart
  • DRV8825 Stepper Motor Driver with Aluminum Heat Sink- Good Quality

    SKU: 52599
     175.00

    (inc GST)

    ₹ 148.31 (+18% GST extra)

    1. Supply Voltage: 8.2 – 42 VDC.
    2. Current Capacity : 2.2A max(24V).
    3. Continuous current per phase: 1.5 A.
    4. Minimum Logic voltage: 2.5V.
    5. Maximum Logic Voltage: 5V.
    6. Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32.
    7. Dimensions : 15 x 20 mm.
    8. Weight: 4 gm.
    Add to cart
  • Enhanced Cytron 40Amp DC Motor Driver (Peak 80amp) MDS40B

    SKU: 11648
     5,239.00

    (inc GST)

    ₹ 4439.83 (+18% GST extra)

    1. Bi-directional control for a single brushed DC motor.
    2. Support motor from 10V to 45V.
    3. Maximum current up to 80A peak, reduce to 40A gradually according to temperature.
    4. 16 KHz switching frequency for quiet operation.
    5. NO Reverse polarity protection.
    6. Protection of overvoltage.
    Add to cart
  • IRF520 MOSFET Driver Module For Arduino ARM Raspberry pi

    SKU: 44050
     110.00

    (inc GST)

    ₹ 93.22 (+18% GST extra)

    1. Voltage: 3.3 – 5V.
    2. Ports: Digital Level.
    3. Output load voltage: 0-24 V.
    4. Output load current: <5A (1A above need to add heat sink).
    5. Platform: Arduino, MCU, ARM, raspberry pi.
    6. Using original IRF520 Power MOS, you can adjust the output PWM
    Add to cart
  • L293D Motor Driver/Servo Shield for Arduino

    SKU: 9736
     179.00

    (inc GST)

    ₹ 151.69 (+18% GST extra)

    1. 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
    2. 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes.
    3. Can run motors on 4.5VDC to 25VDC.
    4. Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
    5. Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
    6. Pull down resistors keep motors disabled during power-up
    7. Big terminal block connectors to easily hook up wires (18-26AWG) and power
    8. 2-pin terminal block and jumper to connect external power, for separate logic/motor supplies
    Add to cart
  • L298N 2A Based Motor Driver Module – Good Quality

    SKU: 43821
     159.00

    (inc GST)

    ₹ 134.75 (+18% GST extra)

    1. Current Sense for each motor.
    2. Heatsink for better performance.
    3. Power-On LED indicator.
    4. Double H bridge Drive Chip: L298N.
    5. Operating Voltage(VDC): 5~35
    6. Peak Current (A): 2
    7. Continuous Current (A): 0-36mA
    8. No. of Channels: 2
    9. Over-Current Protection (A): Yes
    10. Thermal Protection: Yes
    Add to cart
  • L298N Dual H Bridge DC/Stepper Motor Driver Controller Module

    SKU: 51971
     199.00

    (inc GST)

    ₹ 168.64 (+18% GST extra)

    1. Driver chip: L298N Dual H Bridge
    2. Supply voltage: VMS 5V – 35V
    3. Peak current IO: 2A per bridge
    4. Max power consumption: 20W
    5. Provides 4 LEDs that reflect the state of the control logic
    6. Independent direction, speed, and braking for each motor
    Add to cart
  • L9110S DC Stepper Motor Driver Board (Normal Quality)

    SKU: 75496
     99.00

    (inc GST)

    ₹ 83.9 (+18% GST extra)

    1. L9110S-chip motor drive
    2. Supply voltage: 2.5-12V
    3. The maximum operating current of 0.8A
    4. Drive two DC motors or a 4-wire 2-phase stepping motor.
    5. Ultra-small size, suitable for assembly
    Add to cart
  • MD13S 13Amp DC Motor Driver – GROVE Compatible

    SKU: 24027
     891.00

    (inc GST)

    ₹ 755.08 (+18% GST extra)

    1. Support motor voltage ranges from  6V to 30V
    2. Maximum current up to 13A continuous and 30A peak (10 seconds).
    3. GROVE compatible
    4. 3.3V and 5V logic level input.
    5. SMD compatible
    6. Peak Current (A): 30 (10 seconds)
    7. Continuous Current (A): 1
    8. No. of Channels: 1
    Add to cart
  • Presall 3D Scanner Board Kit Ciclop Expansion Board

    SKU: 51650
     890.00

    (inc GST)

    ₹ 754.24 (+18% GST extra)

    1. Supply Voltage: 12VDC.
    2. No. of motor drivers mounts: 2.
    3. Onboard Reset button.
    4. Thermal shutdown circuitry.
    5. Ground fault protection.
    6. Load short-circuit protection.
    Add to cart
  • SmartElex 10D DC Motor Driver HAT for Raspberry Pi

    SKU: 128421
     1,189.00

    (inc GST)

    ₹ 1007.63 (+18% GST extra)

    1. Wide 6V to 28V motor Operating Voltage.
    2. Continuous 10A maximum current without Heatsink and 30A peak current for 10 Seconds.
    3. Two brushed DC motor Bidirectional control.
    4. Current limiting at 35A.
    5. PWM frequency up to 32KHz
    6. Support TTL PWM from the microcontroller
    7. Internal thermal shutdown
    8. Under-voltage lockout
    9. PWM and direction controlled driving of four externally powered NMOS transistors
    10. 3V and 5V logic level input.
    Add to cart
  • SmartElex 10S DC Motor Driver HAT

    SKU: 103711
     749.00

    (inc GST)

    ₹ 634.75 (+18% GST extra)

    1. Wide 6V to 28V motor Operating Voltage.
    2. One brushed DC motor Bidirectional control.
    3. Current limiting at 35A.
    4. PWM frequency up to 32KHz
    5. Support TTL PWM from the microcontroller
    6. Internal thermal shutdown
    7. Under-voltage lockout
    Add to cart
  • SmartElex 15D Dual Channel DC Motor Driver

    SKU: 55900
     1,449.00

    (inc GST)

    ₹ 1227.97 (+18% GST extra)

    1. Supply Voltage: 6.8-30 VDC.
    2. Continuous Current: 13 Amp.
    3. PWM Frequency: 20 KHz.
    4. Current limiting at 30A.
    5. 3V and 5V logic level input.
    Add to cart
  • SmartElex 15S DC Motor Driver 15A (30A Peak)

    SKU: 47993
     750.00

    (inc GST)

    ₹ 635.59 (+18% GST extra)

    1. Supply Voltage: 6.8-30 VDC.
    2. Continuous Current: 15 Amp.
    3. PWM Frequency: 20 KHz.
    4. Max Peak current: 30 Amp(For 10 Seconds).
    5. One brushed DC motor Bidirectional control.
    Add to cart
  • TB6560 Driver Board 3A CNC Router Single 1 Axis Controller Stepper Motor

    SKU: 18979
     490.00

    (inc GST)

    ₹ 415.25 (+18% GST extra)

    1. Driver Chip: TB6560AHQ
    2. Operating Voltage: 10-35V
    3. Nominal Voltage: 24V
    4. With the large heat sink to ensure good heat dissipation
    5. 6N137 high-speed OptoCoupler, to ensure a high speed without step out.
    Add to cart
  • TB6600 stepper motor Driver Controller 4.5A 8~50V TTL 16 Micro-Step CNC Single-Axis

    SKU: 49111
     680.00

    (inc GST)

    ₹ 576.27 (+18% GST extra)

    1. Supply Voltage:  8V – 50V DC (36V recommended).
    2. Output current: 0.3A – 4.5A (peak value of 5A).
    3. Micro Step: 1, 2, 8, 16.
    4. Maximum PWM frequency: 200kHz.
    5. Adjustments for the maximum current of the LED: 1A, 2.2A, 3.3A, 4.5A.
    6. Operating temperature: -10 to + 45 ° С.
    Read more
  • TB6600 Stepper Motor Driver Controller 4A 9~42V TTL 16 Micro-Step CNC 1 Axis

    SKU: 43211
     690.00

    (inc GST)

    ₹ 584.75 (+18% GST extra)

    1. Input Current: 0~5A
    2. Output Current: 0.5~4.0A
    3. Control Signal: 3.3~24V
    4. Power (MAX): 160W
    5. Micro Step: 1, 2/A, 2/B, 4, 8, 16, 32
    6. Temperature: -10~45℃
    7. H bridge bipolar constant current drive.
    Add to cart
  • ULN2003 Driver Module Stepper Motor Driver

    SKU: 28379
     103.00

    (inc GST)

    ₹ 87.29 (+18% GST extra)

    1. 5-12V power supply
    2. 4-way signal indicator
    3. Chip all the pins have Input leads Mounted for easy connection to use
    4. XH-5P socket can be connected directly 28BYJ-48 Model stepper motor
    5. Dimensions: 32 x 18 x 11mm (LxWxH)
    6. Weight: 3 gm
    Add to cart
  • ULN2003 Driver Module Stepper Motor Driver Board

    SKU: 312977
     54.00

    (inc GST)

    ₹ 45.76 (+18% GST extra)

    1. ULN2003A motor driver chip
    2. Chip all the pins already leads for easy connection to use
    3. 5-12V power supply
    4. 4-way signal indicator
    5. Step angle: 5.625 x 1 / 64
    6. Reduction ratio: 1 / 64
    7. Phase: 4
    8. Current / Phase: 5V
    Read more
  • MA860H Digital Stepper Micro-Step CNC Motor Driver 50-110 VDC with 1.8-7.5A

    SKU: 6747
     6,667.00

    (inc GST)

    ₹ 5650 (+18% GST extra)

    1. Supply voltage up to 80VAC or +110VDC
    2. Output current up to 7.2A
    3. Pulse input frequency up to 300 KHz
    4. 16 selectable resolutions in decimal and binary, up to 51,200 steps/rev
    5. Suitable for 2-phase and 4-phase motors
    6. Dimensions: 118×75.5×34 (LxWxH) mm
    Add to cart
  • Leadshine DM542 Digital Stepper Motor Driver

    SKU: 6745
     3,412.00

    (inc GST)

    ₹ 2891.53 (+18% GST extra)

    1. Good high-speed performance
    2. Supply voltage up to +50VDC
    3. Output current up to 4.2A
    4. Pulse frequency up to 300 KHz
    5. Automatic idle-current reduction
    6. 3-state current control technology
    7. Self-adjustment technology
    8. Pure-sinusoidal current control technology
    Add to cart
  • A4988 driver Stepper Motor Driver- Good Quality

    SKU: 6722
     149.00

    (inc GST)

    ₹ 126.27 (+18% GST extra)

    1. Supply Voltage : 8-35 VDC.
    2. Current : 1.0A  (no heatsink ).
    3. Current : 2.0A (with heat-sinking).
    4. logic input : 3 – 5.5V .
    5. Automatic current decay mode detection / choice.
    6. Mixed with slow current decay mode.
    Add to cart
  • DRV8825 Stepper Motor Driver with Aluminum Heat Sink

    SKU: 6721
     160.00

    (inc GST)

    ₹ 135.59 (+18% GST extra)

    1. Supply Voltage: 8.2 – 42 VDC.
    2. Current Capacity : 2.2A max(24V).
    3. Continuous current per phase: 1.5 A.
    4. Minimum Logic voltage: 2.5V.
    5. Maximum Logic Voltage: 5V.
    6. Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32.
    7. Dimensions : 15 x 20 mm.
    8. Weight: 4 gm.
    Add to cart
  • Cytron G15 Shield

    SKU: 6265
     892.00

    (inc GST)

    ₹ 755.93 (+18% GST extra)

    1. Arduino reset button
    2. 4 x G15 Cube Servo ports.
    3. External power port for a servo with polarity protection
    4. Stackable I/O header pin
    5. Selectable digital pins for the control pin with mini jumpers
    6. TX and RX indicator LEDs to show communication activities, only on Rev2.0.
    7. Selectable Serial pins, Either hardware serial or software serial via mini jumpers, only on Rev2.0
    Add to cart
  • L298N Based Motor Driver Module – 2A

    SKU: 5828
     148

    (inc GST)

    ₹ 125.42 (+18% GST extra)

    1. Logical voltage: 5V
    2. Drive voltage: 5V-35V
    3. Logical current: 0-36mA
    4. Drive current: 2A (MAX single bridge)
    5. Max power: 25W
    6. Dimensions: 44 x 44 x 28 (LxWxH)mm
    7. Weight: 26 gm
    Add to cart
  • L293D Motor Driver Module

    SKU: 5825
     119.00

    (inc GST)

    ₹ 100.85 (+18% GST extra)

    1. The driver two holes of 3 mm dia.
    2. Male burg-stick connectors for supply, ground and input connection.
    3. Screw terminal connectors for easy motor connection.
    4. High noise immunity inputs.
    5. Operating Voltage(VDC): 4.5 to 12
    6. Peak Current (A): 600 mA
    7. No. of Channels: 1
    Add to cart
  • Cytron SmartDriveDuo-10 MDDS10 DC MOTOR DRIVER

    SKU: 4565
     3,937.00

    (inc GST)

    ₹ 3336.44 (+18% GST extra)

     

    1. Single power operation
    2. Dual Channels means it can drive two brush motor independently, or mixed.
    3. Support Signed magnitude and Locked Anti-phase in PWM mode.
    4. Two manual/test buttons for each channel.
    5. Two output indicator LEDs for each channel.
    6. Power, Error indicator, RUN status (Left and Right) LEDs
    7. On board reset button to restart the MCU after changing operation mode.
    8. Operating modes: RC (RC servo signal), Analog, PWM, simplified and packetized UART.
    Add to cart
  • 10A Motor Driver Shield – MD10

    SKU: 3408
     1,564.00

    (inc GST)

    ₹ 1325.42 (+18% GST extra)

    1. Bi-directional control of 1 brushed DC motor.
    2. Support motor voltage ranges from 7V to 25V, .
    3. Maximum current up to 10A continuous and 15A peak (10 seconds).
    4. Solid state components provide faster response time and eliminate the wear and tear of a mechanical relay.
    5. Fully NMOS H-Bridge for better efficiency and no heat sink is required.
    6. Speed control PWM frequency up to 10KHz.
    7. Selectable digital pins for PWM and DIR.
    Add to cart
  • Cytron MDS160A SmartDrive160 160AMP Dc Motor Driver (Peak 190Amp)

    SKU: 2784
     19,845.00

    (inc GST)

    ₹ 16817.8 (+18% GST extra)

    1. Bi-directional control for a single brushed DC motor.
    2. Support input voltage from 8V to 28V.
    3. Maximum current up to 190A peak (1 minute), 175A (2 minutes) or 160A (continuously).
    4. 16 KHz switching frequency for quiet operation.
    5. LiPo battery low voltage warning.
    6. Thermal protection.
    Add to cart