BIGTREETECH BTT Manta M8P Control Board

Availability:

In stock


SKU: 1611654
  1. Adopt 32-bit 64MHz ARM Cortex-M0+ series STM32G0B1VET6 as the main control chip;
  2. The output current of the chip is up to 5A, and the peak value can reach 6A, which perfectly supports the power supply of Raspberry Pi;
  3. There is a BOOT button reserved on the motherboard, users can update the bootloader through DFU
  4. The thermistor part includes a protection circuit that protects the main control chip from the possibility of burning caused by leakage of the heated bed or heater cartridge
  5. The thermistor can select the pull-up resistor value through the jumper, in this way, it supports PT1000 without an external module, which is convenient for customers to DIY

 6,949.00 (Incl. GST)

In stock

Purchase this product now and earn 70 Robu Points!

Very Low Stock. Order Now !


Free Delivery above ₹499
Free Delivery
above ₹499
1 Year Warranty
1 Year Warranty
Cash On delivery
Cash on Delivery*

Didn’t find what you are looking for?

Category: 3D Printer Display and Controller

This is BIGTREETECH BTT Manta M8P Control Board.

BIGTREETECH Manta M8P Control Board uses 32-bit ARM Cortex-M0+ series STM32G0B1VET6 main control chip with a core frequency of 64MHz. High-performance MOSFETs are used to reduce heat generation. The power chip of Manta M8P integrated main control board adopts TPS5450-5A, which supports DC12/24V power input; the output current of this chip is up to 5A, and the peak value can reach 6A, which perfectly supports the power supply of Raspberry Pi.

The control board and the core board use BTB connection method, so that other core board solutions other than CM4 can be selected, such as BIGTREETECH CB1. The mainboard reserves the SPI expansion interface for using the Klipper firmware to connect an external acceleration sensor for acceleration compensation. The thermistor can select the pull-up resistance value through the jumper, which supports PT1000 without external modules, which is convenient for DIY use; the control board reserves a three-way four-wire fan interface, which can be used to connect a water-cooling device.

Note: Actual product may vary in color. Refer to Manual in the ATTACHMENTS section for more info. regd. the product.


Features:

  1. The MCU firmware can be updated via an SD card, or through Klipper’s make flash command using DFU;
  2. The motherboard and the core board use the BTB connection to allow using other solutions other than CM4;
  3. On-board TMC-driver SPI and UART working modes, on-board DIAG function pins, can be used by simply plugging and unplugging the jumper cap;
  4. Support filament runout detection, auto shutdown, BLTouch, RGB lights…
  5. High efficiency MOSFET for less heat generation;
  6. Adopt replaceable fuse for easy replacement;
  7. Three-way four-wire fan interface is reserved, and can be used to connect the water cooling device;
  8. Provide the SPI expansion interface to allow Klipper firmware users to connect an external acceleration sensor for acceleration compensation

Package Includes:

1 x BIGTREETECH Manta M8P Control Board

1 x Type C USB Cable

1 x DIY Crimp Terminal Set

1 x Black jumper set

 

SKU: 1611654 Category:
Item Type:

Controller Board Only

Model Series:

BTT Manta Series

Microcontroller

STM32G0B1VET6

Frequency Range

64 MHz

Driver Slot

8

Heating interface

HE1, HE2, HE3), heating rod (HE0, hot bed (HB)

Fan Port

2 pins PWM Fan x 5 4pins PWM Fan x 2 Always on Fan x 1 SoC Fan x 1

Fan Voltage Selection (Y/N)

(24V, 12V, 5V), Y

Heater Cartridge Connector

4

Thermistor (Y/N)

100K NTC x 5, Y

USB

1 USB-OTG or UART to USB 3 USB-Host 2.0

HDMI

Micro HDMI x 2

PC Communication Interface

Type-C

Logic Voltage (V)

DC3.3V

Mainboard input voltage

VIN=DC12V or DC24V

Dimensions (mm)

170 x 102 x 18

Weight (g):

186

Shipping Weight 0.318 kg
Shipping Dimensions 21 × 14 × 5 cm
1 Year Warranty

This item is covered with a supplier warranty of 1 year from the time of delivery against manufacturing defects only. In case of manufacturing defects or issues, we will replace the part after warranty confirmation by our technical team, but we won’t offer refunds or replace the entire product.


What voids the warranty:

If the product is subject to misuse, tampering, static discharge, accident, water or fire damage, use of chemicals & soldered or altered in any way.

Based on 0 reviews

0.0 overall
0
0
0
0
0

Be the first to review “BIGTREETECH BTT Manta M8P Control Board”

There are no reviews yet.

Manual

Questions and answers of the customers

    Is it V1 or V1.1 ?
  1. 0 votes
    Q Is it V1 or V1.1 ? answer now
    Asked by kundanpatelmp on June 9, 2024 3:07 pm
    A Hello, for your query please reach to us by rising... Read more
Only registered users are eligible to enter questions
Country Of Origin: China