Capacitor Touch Dimmer, Constant Voltage LED Stepless Dimming, PWM Control Board

Availability:

In stock


SKU: 399049

It can control LED module, light and so on. It is available for indoor LED, lighting lamp, DIY automotive lights dimming refit.

With Single touch, using the principle of capacitance touch. The default function is a switch, dimming, with brightness memories LED touch dimming. It will light slowly when turning on the lights, and become dark slowly when turn off, which effectively avoid the stimulation to eyes.

 110.00

(inc GST)

₹ 93.22 (+18% GST extra)

In stock

Purchase this product now and earn 2 Robu Points!
Brand: Generic
Category: Electronic Switches/Keypads

The default function of the capacitor touch dimmer is a switch, dimming, with brightness memories LED touch dimming. It will light slowly when turning on the lights, and become dark slowly when turn off, which effectively avoid the stimulation to eyes.

The lamp brightness can be adjusted by requirement, it is very to operate. It can touch in medium protection, such as glass, acrylic, plastic, ceramics and so on, which is very safe.

PCB board(VCC,GND) is power input
  1. (LED+, LED-) is connected with the LED lamps of positive and negative level (fingerprint) touch area
  2. Copper skin area should be 2x3cm.
  3. T1=1, T2=1: Without brightness memory, suddenly light and off LED touch Stepless dimming function.
  4. T1=0, T2=1: Without brightness memory, gradually light and off LED touch Stepless dimming function.
  5. T1=1, T2=0: With brightness memory, gradually light and off LED touch Stepless dimming function.
  6. T1=0,T2=0:LED three sections touch dimmer function.
Using method
  1. Click touch (touch duration time is less than 550ms) can control the lamp. Click once, the lamp lights; click again, the lamp off. The initial brightness of lights lit the fixed for the whole brightness of 90%.
  2. Press the touch at a long time (touch duration time is more than 550ms), you can achieve step-less dimming the lights. Press long time once, light levels gradually increase light levels when released after the release time parked in the corresponding brightness, long time if more than three seconds, the light levels to achieve maximum brightness does not change; again long press touch, light levels gradually decreased to stop when you release the light levels in the corresponding brightness release time, if a long time more than three seconds, the light levels after reaching the minimum brightness does not change.

Note: This Product is available in two different variants (FC-106 and HW-206) with the same working we will ship it randomly.


Specifications and Features:

  1. The lamp brightness can be adjusted by requirement, it is very to operate.
  2. It can touch in medium protection, such as glass, acrylic, plastic, ceramics and so on, which is very safe.
  3. Simple applied circuit, less peripheral devices, easy processing, low cost.
  4. Anti-power and phone interference, the EFT can reach above +/-2KV; the touch response sensitivity and reliability will not be affected by the close distance or multi-angle mobile phone interference.
  5. Install: Needn’t to touch copper foil directly, the dimming can be processed across the acrylic glass(above 3mm) or plastic.
  6. Application: It can control LED module, light and so on. It is available for indoor LED, lighting lamp, DIY automotive lights dimming refit.
  7. Function: Single touch, using the principle of capacitance touch. The default function is a switch, dimming, with brightness memories LED touch dimming. It will light slowly when turning on the lights, and become dark slowly when turn off, which effectively avoid the stimulation to eyes.
  8. Dimming mode: Non-polar PWM dimming.
  9. Wiring method: PCB board(VCC, GND) is power input, (LED+, LED-) is connected with the LED lamps of positive and negative level (fingerprint) touch area, also can wire to lead out (the wiring should not be too long), copper skin area should be 2x3cm. With copper foil, copper foil board module will side to the shell side.

Package Includes:

1 x Capacitor Touch Dimmer, constant voltage LED Stepless Dimming, PWM Control Board

Operating Voltage (VDC)

2.4 ~ 4.5

Aperture (mm)

16

Length (mm)

39

Width (mm)

19

Height (mm)

11

Weight (gm)

3

Shipment Weight

0.005 kg

Shipment Dimensions

9 × 7 × 5 cm

15 Days Warranty

This item is covered with a standard warranty of 15 days from the time of delivery against manufacturing defects only. This warranty is given for the benefit of Robu customers from any kind of manufacturing defects.  Reimbursement or replacement will be done against manufacturing defects.


What voids warranty:

If the product is subject to misuse, tampering, static discharge, accident, water or fire damage, use of chemicals & soldered or altered in any way.

Based on 0 reviews

0.0 overall
0
0
0
0
0

Be the first to review “Capacitor Touch Dimmer, Constant Voltage LED Stepless Dimming, PWM Control Board”

There are no reviews yet.

Questions and answers of the customers

There are no questions yet. Be the first to ask a question about this product.

Only registered users are eligible to enter questions