Categories
View cart “SP Racing F3 Flight Controller Integrate OSD Deluxe Version” has been added to your cart.
Naze32 10DOF Flight Control board
Naze32 10DOF Flight Control board naze32 6 dof 3 naze32 6 dof 1 naze32 6 dof 4

Naze32 10DOF Flight Control Board

2 Review(s)
Availability: In stock
SKU: 29597

QUICK OVERVIEW

  1. Axis: 2000 degrees/second 3-axis MEMS gyro.
  2. Input voltage: Max 16V on input rail and up to 35V 6s on the voltage sense line.
  3. Built-in FrSky telemetry inverter (shared w/main port).
  4. A modern 32-bit processor running at 3.3V/72MHz (STM32F103CB).
  5. Onboard MicroUSB for setup and configuration.
  6. Multi WiFi-based configuration software for easy setup.

 1,615.00

(inc GST)

₹ 1368.64 (+18% GST extra)

In stock

Purchase this product now and earn 17 Robu Points!
Category: Tag:

Naze32 10DOF Flight Control board is designed to run on most frames with stock PIDs, just a few minor settings to get it going. It flies extremely well and offers stunt mode (no auto-level), Horizon Mode (auto level when sticks near the center, so you can still flip, etc), and Angle mode (always auto level and limit bank and pitch to 45 degrees). Tight flips and pinpoint point rolls are possible.

The plus version includes a Magnetometer and Barometer required for GPS functionality and heads free modes. Designed for standard servo connectors (no special cables), and vertical pins to reduce overall footprint. It will run the 32 bit port of the MultiWii RC flight controller firmware, running an ATmega32u4. Use the Chrome Baseflight Configurator for the GUI.

The BMP280 barometer and an HMC5833 compass sensor. Adding a compass sensor helps with getting better aircraft heading measurements while you are flying, but most importantly it allows you to add a GPS module to enable position hold flight mode with your drone.

Note:
  1. Flashing/Updating the Default firmware may cause a problem of connectivity with PC/Laptop.
  2. The Magnetometer of this board works only with  Clean Flite Version V1.2.3

Since this is an Open Source Flight Controller Board, there are many manufacturers who are supplying this product. We have picked up the best quality products from the market and tested them for their functionality. And finally selected best amongst them. Our product works exactly the same as we have described above in the description.


Installation Process:
  1. Clone the repo to any local directory or download the ZIP file in Attachments
  2. Start Chromium or Google Chrome browser and go to tools -> Extension
  3. Check the “Developer mode” checkbox (ON the developer mode)
  4. Click on “Load Unpacked” button on the upper right corner of the extension page and
  5. Browse and Select the Downloaded ZIP file from your computer


Features :

  1. Version:10 DOF
  2. Axis: 2000 degrees/second 3-axis MEMS gyro.
  3. Input voltage: Max 16V on input rail and up to 35V 6s on the voltage sense line.
  4. Flexible motor outputs, support various airframe types: Quad/Hexa/Tri/Bi/Y4/Y6/Octo/Camera Gimbal. (Default is Quad-X).
  5. Up to 8 ch RC input – supports standard receivers (PWM), PPM Sum receiver (FrSky, etc), or Spektrum satellite receivers.
  6. Built-in FrSky telemetry inverter (shared w/main port).
  7. Battery voltage monitoring.
  8. A modern 32-bit processor running at 3.3V/72MHz (STM32F103CB).
  9. Onboard MicroUSB for setup and configuration.
  10. LEDs so bright, they could blind you.
  11. Multi WiFi-based configuration software for easy setup.

 


 Package Includes :

1 x Naze32 10DOF Flight Control board.

1 x Set of Berg pins.

1x Protective Plastic Case.

1 x Connecting Cable.

Model

Naze32 10DOF

Input Voltage (V)

3.3 ~ 5 VDC

Firmware

Naze Firmware

Sensors

MPU6500

Processor

Morden 32-bit STM32F103CB

Micro-SD Card Slot

No

Dimensions (mm) LxWxH

(Without Case)
36 x 36 x 7

Weight (gm)

10

Shipment Weight

0.125 kg

Shipment Dimensions

10 x 8 x 5 cm

15 Days Warranty

This item is covered with a standard warranty of 15 days from the time of delivery against manufacturing defects only. This warranty is given for the benefit of Robu customers from any kind of manufacturing defects.  Reimbursement or replacement will be done against manufacturing defects.


What voids warranty:

If the product is subject to misuse, tampering, static discharge, accident, water or fire damage, use of chemicals & soldered or altered in any way.

2 reviews for Naze32 10DOF Flight Control Board

  1. Rated 5 out of 5

    Chirag Mehra (verified owner)

    Nice flight controller with preinstalled firware and easy to setup and use.. . directly plug and play….all the sensor on board and stm32 chip.

  2. Rated 5 out of 5

    mayurkumarchauhan19@gmail.com

    very very excellent

Add a review

Your email address will not be published. Required fields are marked *

Clean Flight V1.2.3