Generic
Showing 4609–4656 of 6091 results
-
-
-
Bluetooth and NRF Modules, Compatible with Arduino Boards
BLE Nano Integrated CC2540, Bluetooth Module with, Soldering
Bluetooth and NRF Modules, Compatible with Arduino BoardsBLE Nano Integrated CC2540, Bluetooth Module with, Soldering
SKU: 1121280BLE chip: TICC2540Working channel: 2.4GInterface: Micro-USBInput voltage: Micro-USB power supply, Vin6~12V, 5VMicroprocessor: ATmega328P-MU QFN32Bootloader: Latest arduino1.8.8Pin: two rows 2.54mm-15PinSKU: 1121280 -
-
LORA Module
Wireless Transmitter 433Mhz, Lora Shield for Leonardo,, UNO, Mega2560,, Duemilanove, Due
SKU: 1121437- Compatible with 3.3v or 5v I/O Arduino Board.
- Frequency Band:Â Â 433 MHZ (Pre-configure in factory)
- Low power consumption
- Compatible with Arduino Leonardo, Uno, Mega2560, DUE
- External Antenna via SMA Jack
SKU: 1121437 -
PIR / IR and Optical Sensor
M5 LTD-05NO 130MM Laser, Micro Diffuse Reflectance, Photoelectric Switch, Laser Visible Light
PIR / IR and Optical SensorM5 LTD-05NO 130MM Laser, Micro Diffuse Reflectance, Photoelectric Switch, Laser Visible Light
SKU: 1121351- Model: M5 LTD-05NO
- Operating Voltage:10 ~30 V
- No-load current:9 mA
- Output Current:150 mA
- Operating Frequency:120 Hz
- Diameter: M5
- Detect Distance:130 mm
- Light spot Size:1.0 mm
SKU: 1121351 -
-
-
IoT Development Boards
JTAGulator with JTAG Exploitation Learning kit
SKU: 1051958- 24 I/O channels with input protection circuitry
- Adjustable target voltage: 1.2 V to 3.3 V
- Supported target interfaces (as of firmware v1.1): JTAG/IEEE 1149.1, UART/asynchronous serial
- USB interface for direct connection to the host computer
SKU: 1051958 -
-
Relay Modules
8 Channel Relay Module 12V High and Low Level Trigger Relay Module
SKU: 1794669- Operating Voltage: 12V DC
- Maximum Load: AC: 250v/10a; DC: 30v/10a
- Isolation: SMD Optocoupler Isolation with two fully isolated power supply systems
- Drive Modes: High-level and Low-level drive mode
SKU: 1794669 -
DIY Hobby Project Parts
ZVS Driver Board for Tesla Coil Power Supply Board Induction Heating Module 12-30V
DIY Hobby Project PartsZVS Driver Board for Tesla Coil Power Supply Board Induction Heating Module 12-30V
SKU: 1794283- Input Voltage: DC 12V-30V
- Output: HVDC, About 800 times of input voltage
- Power Requirements: Less than 12V ≥ 5A, above 15V ≥ 15A
- Operating Frequency: 30kHz-50kHz adaptive
SKU: 1794283 -
Through Hole DIP LEDs
3-24V Breathing Lamp Module LED Light Gradually Turn Off and Gradually Turn On Mode
Through Hole DIP LEDs3-24V Breathing Lamp Module LED Light Gradually Turn Off and Gradually Turn On Mode
SKU: 1794185- Input voltage: universal input DC 3-24V
- Output voltage: equal pressure output
- Wiring port: V+V- is the DC voltage input terminal, LED+LED- (L+L-) is the output connected to the load
SKU: 1794185 -
-
GPS Modules
GNSS Receiver BOB with IRNSS
SKU: 1535408- L1, L5 signal reception to support GPS and NavIC. Works with NavIC, GAGAN, GLONASS,
- GPS satellites and more. Support for AGPS.
- Support for Automotive Dead Reckoning (ADR), Odometer-less Dead Reckoning (ODR) with either built-in sensors within the GNSS BOB or with external sensors.
- Optional Real-time Kinematic (RTK) module for Centimetre level precision and accuracy.
- Less than 33 second cold start TTFF.
SKU: 1535408 -
-
Interface Connector
UCTRONICS Gigabit PoE Splitter 5V 3A, 2-in- 1 PoE to USB C/ Micro USB Adapter, for Raspberry Pi 3/4, Security IP
Interface ConnectorUCTRONICS Gigabit PoE Splitter 5V 3A, 2-in- 1 PoE to USB C/ Micro USB Adapter, for Raspberry Pi 3/4, Security IP
SKU: 1458287- Product: Gigabit PoE Splitter 5V 3A, 2-in- 1 PoE to USB C/ Micro USB Adapter
- Operating Power: DC38~57V IEEE 802.3af/at PoE
- Output Power(Watt):Â 15
- Data Output Port: RJ45 Male
- Power Output Ports: Â Micro USB male port; Micro USB female to USB-C male port.
SKU: 1458287 -
