Flight Controller & Accessories

1. Dimensions: 37 x 37 x 10 mm(L x H x W)
2. Weight: 12 gm.
3. SPI Gyro MPU6000
4. MicroSD Blackbox
5. F4 Processor (F405)
6. 5v3a SBEC
7. Built-in Current Sensor
8. On-Board OSD (controlled by Beta flight, FC over SPI bus)
9. On-Board Video Filter (only can supply 5V to VTX and Camera)
10. On-Board Voltage Regulator and Power supply (BEC)

1. Supported Receiver Input Signal: PPM, SBUS, DSM
2. Support PPM, SBUS, DSM receiver input signal
3. Battery voltage detection and buzzer interface
4. Run on SP RACING F3 EVO firmware 32 brush flight control
5. Large current NMOS transistors, operating current can reach 10A or higher
6. Use STM32F303CCT6 + MPU6500, advanced hardware platform F3 for higher flight stability

1. Color: Black.
2. Material: Glass Fiber
3. Weight: 15 gm.
4. Dimensions: 45 x 45 mm
5. Suitable for:  CC3D flight controllers, Naze32, Mini APM etc

1. USB connector is used to connect to the USB port on your GoPro Hero3 Camera.
2. The 3 pin female connector is for AV video output

Typical application:

Video output from your GoPro Hero 3 USB port to your video wireless transmitter. (Connect your GoPro Hero 3 directly to FPV transmitter)

1. Stainless steel material for long-term use
2. Inbuilt Colorful Ring illumination LED
3. Available in Various LED Color
4. Bright daylight LEDs

1. Supported Receiver Input Signal: PPM, SBUS, DSM
2. Support PPM, SBUS, DSM receiver input signal
3. Battery voltage detection and buzzer interface
4. Large current NMOS transistors, operating current can reach 10A or higher
5. Use STM32F303CCT6 + MPU6500, advanced hardware platform F3 for higher flight stability

1.  Stackable design – perfect for integrating with OSDs and power distribution boards.
2. 16 PWM I/O lines for ESCs, Servos and legacy receivers. 8 available on standard pin headers. 8 via side mounted connectors.
3. Full support for OneShot ESCs for easy PID tuning and a sharper response.
4. Supports SBus, SumH, SumD, Spektrum1024/2048, XBus, PPM, PWM receivers.
5. No external inverters required (built-in).
6. Dedicated output for programmable LEDs – great for orientation, racing and night flying.
7. Dedicated I2C port for connection of OLED display without needing flight battery.
8. Battery monitoring ports for voltage and current.
9. Sonar support for precision low-altitude hold.
10. Buzzer port for audible warnings and notifications.
11. Symmetrical design for a super tidy wiring.
12. Barometer mounted on the bottom of the board for easy wind isolation.
13.  Wire up using pin headers, JST-SH sockets or solder pads. Use either right-angled or straight pin-headers.

1. ATmega328P with Arduino bootloader.
2. MAX7456 monochrome on-screen display.
3. +5V 500mA regulator for up to +12V supply input.
4. FTDI cable compatible pinout.
5. The standard 6-pin ISP header.
6. Standalone, or with APM/ Flip / Flip32+ flight controllers.

1. 2000 degrees/second 3-axis MEMS gyro + accelerometer (MPU6500).
2. Input voltage: Max 16V on input rail and up to 35V 6s on the voltage sense line.
3. Fully pinout compatible with rev5 accessories (OSDoge etc).
4. SBUS Inverter.
5. Sonar pads w/resistors added for direct connection to 5V sonar.
6. MS5611 barometer.
7. 128mbit flash.

1. 36x36mm board with 30.5mm mounting holes
2. STM32F303 CPU, 72Mhz inc FPU
3. High-Capacity Flash
4. MPU6050 accelerometer/gyro
5. MS5611 barometer (Deluxe only)
6. HMC5883 compass (Deluxe only)

1. Main FMU Processor: STM32F76
2. 32 bit ARM® Cortex® M7, 216 MHz Processor running NuttX RTOS,
3. More computing power and 2X the RAM than previous versions)
4. Abundant connectivity options for additional peripherals (UART, I2C, CAN)
5. Redundant power supply inputs and automatic failover
6. External safety button for easy motor activation
7. New sensors with higher temperature stability
8. Multicolor LED indicator
9. Integrated vibrations isolation
10. High-power, multi-tone piezo audio indicator
11. microSD card for long-time high-rate logging