Shield for Arduino
Showing 49–60 of 60 results
-
Shield for Arduino
Sensor Shield V5 Expansion Board For Arduino
SKU: 26598- Retain the merits of the V4.0 version
- Laminated design
- PCB immersion gold processing technology
- IIC interface
- Bluetooth module communication interface
- SD card module communication interface
- APC220 wireless rf modules communication interface
- RB URF v1.1 ultrasonic sensors interface
- 12864 LCD string of line and parallel interface
- 32 servo controller interface
SKU: 26598 -
Shield for Arduino
Servo Driver Module Shield 16 Channel
SKU: 31371- The I2C input, PWM output control 16 roads, steering gear can 16 roads.
- The steering gear power independent V + input maximum 6 V.
- Logic signals and logical power independent output for 3V to 5 V.
- 40-1000 Hz frequency.
- Terminal block for power input.
- Reverse polarity protection on the terminal block input
- Green power-good LED
SKU: 31371 -
Shield for Arduino
SmartElex PS2 Sheild for Arduino
SKU: 217461- Simple to use UART protocol
- Vibrator motor on PS2 is controllable.
- Wired and Wireless PS2 controller is supported.
- PS2 Controller will automatically operate in analog mode. (Default)
- A status LED
- Jumper selector to select different UART Baud Rate (74880 (Default), 9600, 57600, 115200). Default: – when no jumper is attached.
- Jumper selectors to select different digital pin as UART – TX and RX pin.
SKU: 217461 -
Shield for Arduino
UNO Proto Shield prototype expansion board with SYB-170 mini breadboard
SKU: 28256- It has a nice standard 0.1″x0.1″ prototyping grid with big pads
- Comes with Stacking headers and plain header, choose whichever you want when soldering together
- An IC pattern for adding DIP ICs up to 20 pins
- Power rails down the middle and sides
- A reset button and an extra general use button
- Two 3mm general use LEDs, red and green, as well as 2 matching resistors
SKU: 28256 -
Audio Amplifier Module, Shield for Arduino
VS1053 MP3 Recording Module Development Board with Onboard Recording Function
Audio Amplifier Module, Shield for ArduinoVS1053 MP3 Recording Module Development Board with Onboard Recording Function
SKU: 396204- SPI interface, the control signal lines are led out
- A headphone and stereo output
- Onboard Microphone for recording
- A line-in input interface
- Separate 3.5 mm Jack for MIC and Speaker
- Onboard Power Indicator
- 3.3V and 2.8V of LDO chip AMS-1117 on board provides up to 800mA current
SKU: 396204 -
Shield for Arduino
XBee IO Expansion Shield – XBEE 2
SKU: 10038- Expand 14 digital IO interface (12 steering gear interface)and power
- Six analog IO interfaces and power
- One digital port interface for external power supply terminals
- Digital port external power supply and on-board electrical automatic switch
- One external power input terminals and one input needle
- RS485 interface (D0-RX, D1-TX, D2-EN)
- IIC/the I2C/TWI interface (A4-SDA, A5-SCL)
- SD card module interface
SKU: 10038 -
Shield for Arduino
XBee Shield V03 Module Wireless Control
SKU: 12197- Stackable design, easy to plug into the ARDUINO development board.
- Coupled with the Arduino Bluetooth Bee Bluetooth module, and other Bluetooth devices can communicate Wirelessly.
- 3.3v and 5v dual power output.
- 3.3v and 5v IO compatible.
- USB2.0 protocol.
SKU: 12197 -
Shield for Arduino
XD-216 Screw shield Screw Shield V1 Expansion Board
SKU: 31175- Size: 29 x 71 mm
- Combines the function of Arduino Screw Shield and Sensor Shield.
- Expand all of IO interfaces from Arduino.
- 3-Pin male headers for easy sensor/servo connection.
- The Screw terminal can be screwed directly to the terminal on the thread and is reliable and convenient.
SKU: 31175 -
Shield for Arduino
SHIELD-EKG-EMG
SKU: 6320- Stackable connectors – up to 6 channels can be stacked and wired to A0-A6 analogue inputs
- Calibration signal generation by D4/D9 digital output
- Precise trimmer potentiometer for calibration (all boards are shipped completely assembled, tested and calibrated so that you don’t have to do this unless you want to see how things works)
- Input connector for standard or active electrodes
- Works with both 3.3V and 5V Arduino boards
SKU: 6320 -
Shield for Arduino
Cytron G15 Shield
SKU: 6265-
Arduino reset button
-
4 x G15 Cube Servo ports.
-
External power port for a servo with polarity protection
-
Stackable I/O header pin
-
Selectable digital pins for the control pin with mini jumpers
-
TX and RX indicator LEDs to show communication activities, only on Rev2.0.
-
Selectable Serial pins, Either hardware serial or software serial via mini jumpers, only on Rev2.0
SKU: 6265 -
-
Shield for Arduino
ADK USB Host Shield compatible with Arduino
SKU: 3366- Works with standard (dual 5/3.3V) and 3.3V-only (for example, Pro Arduino) boards.
- Complies with USB Specification Revision 2.0 (Full-Speed 12Mbps Peripheral, Full-/Low-Speed 12Mbps/1.5Mbps Host)
- Supports HID devices, such as keyboards, mice, joysticks, etc.
- Compatible with Mass storage devices, such as USB sticks, memory card readers, external hard drives (FAT32 Type File System – Mega Arduino only).
SKU: 3366