Motors | Drivers | Pumps | Actuators
Showing 49–96 of 1558 results
-
-
Servo Motor Drivers
16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
Servo Motor Drivers16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
SKU: 43740- Adjustable frequency PWM up to about 1.6 KHz
- 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
- Configurable push-pull or an open-drain output
- The output enable pin to quickly disable all the outputs
- Terminal block for power input
- Reverse polarity protection on the terminal block input
- Green power-good LED
SKU: 43740 -
Futaba servo cable
JR Female To JR Female Servo Extension Wire (100mm)
SKU: 58188- Item Name: servo extension wire
- 100% Brand new and high quality.
- Plug type: JR Female To JR Female type
- Length: 100mm(30core/26AWG).
- Color: Red, Black, White(Or brown, red, orange)
- Useful for RC Car, plane, helicopter, and drone servo connection or receiver connection.
SKU: 58188 -
-
-
Brushed / Brushless DC motor Driver
L293D Motor Driver Module
SKU: 1501289- The driver two holes of 3 mm dia.
- Male burg-stick connectors for supply, ground and input connection.
- Screw terminal connectors for easy motor connection.
- High noise immunity inputs.
- Operating Voltage(VDC): 4.5 to 12
- Peak Current (A): 600 mA
- No. of Channels: 1
SKU: 1501289 -
N20 Metal Gear Motors
N20-12V-600 Rpm Micro Metal Gear Motor
SKU: 51872- This is a DC Mini Metal Gear Motor, ideal for making robots
- Lightweight, high torque and low RPM.
- Fine craftsmanship, durable, not easy to wear.
- With excellent stall characteristics, can climb hills easily.
- You can also easily mount a wheel on the motor’s output shaft.
SKU: 51872 -
-
Brushed / Brushless DC motor Driver
Motor Driver TB6612FNG Module Performance Ultra Small Volume 3 PI Matching Performance Ultra L298N
Brushed / Brushless DC motor DriverMotor Driver TB6612FNG Module Performance Ultra Small Volume 3 PI Matching Performance Ultra L298N
SKU: 43846- CW/CCW/short break/stop motor control modes
- Built-in thermal shutdown circuit and a low voltage detecting circuit
- Standby control to save power
- CW/CCW/short brake/stop motor control modes
- Operating Voltage(VDC): 15
- Peak Current (A): 3.2
- Continuous Current (A): 1.2
- No. of Channels: 1
SKU: 43846 -
Futaba servo cable
1JR Male To 2 Futaba Female Y Type Servo Extension Wire(300mm)
SKU: 58171- Item Name: servo extension wire
- 100% Brand new and high quality.
- Plug type: 1-Male(JR), 2-Female(futaba) Y-type
- Length: 300mm(30core/26AWG).
- Color: Red, Black, White(Or brown, red, orange)
- Fit for Futaba and JR receiver.
- Useful for RC Car, plane, helicopter and drone servo connection or receiver connection.
SKU: 58171 -
-
-
-
-
Brushed / Brushless DC motor Driver
L293D Motor Driver Module
SKU: 5825- The driver two holes of 3 mm dia.
- Male burg-stick connectors for supply, ground and input connection.
- Screw terminal connectors for easy motor connection.
- High noise immunity inputs.
- Operating Voltage(VDC): 4.5 to 12
- Peak Current (A): 600 mA
- No. of Channels: 1
SKU: 5825 -
Brushed / Brushless DC motor Driver
20A PWM DC Motor Speed Regulator Module (9V, 12V, 24V, 36V, 48V, 60V)
Brushed / Brushless DC motor Driver20A PWM DC Motor Speed Regulator Module (9V, 12V, 24V, 36V, 48V, 60V)
SKU: 51649- Adjustable speed range: 0%-100%.
- Speed adjustment way: Potentiometer.
- Output voltage: Linear under load.
- Speed control type: Basins.
- Output voltage: Load Linear
- Type: Adjusting flow
- The motor running condition adjustment: Forward  / Stop / Reverse
SKU: 51649 -
-
TowerPro and Other Servo Motors
TowerPro MG996R Digital High Torque Servo Motor (360° Rotation)
SKU: 618530- Weight: 55g
- Dimension: 40.7×19.7×42.9mm
- Stall torque: 9.4kg/cm (4.8v); 11kg/cm (6.0v)
- Operating speed: 0.19sec/60degree (4.8v); 0.15sec/60degree (6.0v)
- Operating voltage: 4.8 ~ 6.6V
- Gear Type: Metal gear
- Dead band width: 1us
- Wire length: 32cm
SKU: 618530 -
L-Type DC BO Motors
150 RPM BO Motor- L Shape
SKU: 2166- Low density: lightweight, low inertia.
- Capability to absorb shock and vibration as a result of elastic compliance.
- Ability to operate with minimum or no lubrication, due to inherent lubricity.
- The relatively low coefficient of friction.
- Operating Voltage(VDC): 3~12
- Shaft Length (mm): 8.5
- Shaft Diameter (mm): 5.5 (Double D-type)
- No Load Current: 40-180mA.
- Rated Speed(After Reduction): 150 RPM
- Rated Torque: 0.8 Kgcm
SKU: 2166 -
Stepper Motor Drivers
L298N Dual H Bridge DC/Stepper Motor Driver Controller Module
SKU: 51971- Driver chip: L298N Dual H Bridge
- Supply voltage: VMS 5V – 35V
- Peak current IO: 2A per bridge
- Max power consumption: 20W
- Provides 4 LEDs that reflect the state of the control logic
- Independent direction, speed, and braking for each motor
SKU: 51971 -
-
-
Other Metal Geared Motors
100RPM 12V Low Noise Dc Motor With Metal Gears – Grade A
SKU: 1137796- The metal gears have better wear and tear properties.
- The gearbox is sealed and lubricated with lithium grease and requires no maintenance.
- Although the motor gives 100 RPM at 12V, the motor runs smoothly from 4V to 12V and gives a wide range of RPM, and torque.
- The shaft has a hole for better coupling.
- Operating Voltage(V): 12
- Rated Torque(kg-cm): 2.9
- Stall Torque(kg-cm): 11.4
SKU: 1137796 -
-
Orange 12V Johnson Geared Motor
EasyMech Bracket For SPG30E & Orange Johnson DC Geared Motor
SKU: 83641- Material: 1.5 mm thick MS steel
- Motor mounting side: Height 48 mm, Width 40 mm;
- Bracket mounting side: Length 30 mm, Width 40 mm
- The holes for Motor mounting: M3.
- Holes for Bracket mounting:Â M4.
- Weight: 32 gm
SKU: 83641 -
TowerPro and Other Servo Motors
TowerPro MG995 Servo High-Speed Digital Metal Gear Servo Motor with CNC Aluminum Steering Servo Horn Arm- Good Quality
TowerPro and Other Servo MotorsTowerPro MG995 Servo High-Speed Digital Metal Gear Servo Motor with CNC Aluminum Steering Servo Horn Arm- Good Quality
SKU: 48176- Model: MG995
- Weight: 55 gm
- Operating voltage: 4.8V~ 7.2V
- Servo Plug: JR
- Stall torque @4.8V : 13kg-cm
- Stall torque @6.6V : 15kg-cm
SKU: 48176 -
N20 Metal Gear Motors
N20-6V-600 Rpm Micro Metal Gear Motor
SKU: 75822- This is a DC Mini Metal Gear Motor, ideal for making robots
- Lightweight, high torque and low RPM.
- Fine craftsmanship, durable, not easy to wear.
- With excellent stall characteristics, can climb hills easily.
- You can also easily mount a wheel on the motor’s output shaft.
SKU: 75822 -
Generic Mini Pumps
15L High Flow 555 Vacuum Pump, Air Pump, Oxygen Pump, Fish Tank Folding
SKU: 76749- Operating voltage: 12 VDC
- Rated current: 800mA
- Inflation time: <6 seconds (from 0 to 300 mmHg in a 1000CC closed container)
- Minimum pressure: >400 mmHg (53.33KPa)
- Maximum pressure: 750.062mmHg (100KPa)
- Hermeticity: <5mmHg (from 1000mmHg in 1000CC container min), airtight only for inflation
- Flow rate: >15 L/Min
- Noise: <55dB (test at 30cm distance)
- Lifetime: 100,000 cycles tested
SKU: 76749 -
Solenoids and Electromagnets
JF-0630B DC 24 V 300mA 10mm 6N Push Pull Solenoid Electromagnet
SKU: 31435- Iron Body Material
- High quality ultra-compact electric lock.
- Rustproof, durable, safe, convenient to use.
- Suction which tightly sucks the iron, thus locking the door.
- Designed with the open frame type and mount board, high power.
- Easy to install for the electric door lock or other automatic door lock systems with the mounting board
- Applicable for being installed in the escape door or fire door electronic controlled system.
- Adopts the principle of electric magnetism, when the current through the silicon, the electromagnetic lock will achieve a strong.
SKU: 31435 -
-
Solenoids and Electromagnets
DC 12V KK-P25/20 8KG Lifting Solenoid Electromagnet
SKU: 130279- Operating Voltage: 12V DC
- Lifting Capacity: 8KG
- Size (D x L): 25 x 20 mm
- Electric lifting magnet.
- Powerful and compact.
- Smooth and flat surface.
- Low consumption and reliable.
- Ambient temperature within 130 degrees.
SKU: 130279 -
L-Type DC BO Motors
300 RPM L-Shape BO Motor
SKU: 103957- Low density: lightweight, low inertia.
- Capability to absorb shock and vibration as a result of elastic compliance.
- Ability to operate with minimum or no lubrication, due to inherent lubricity.
- The relatively low coefficient of friction.
- Operating Voltage(VDC): 3~12
- Shaft Length (mm): 8.5
- Shaft Diameter (mm): 5.5 (Double D-type)
- No Load Current: 40-180mA.
- Rated Speed(After Reduction): 300 RPM
- Rated Torque: 0.35 Kgcm
SKU: 103957
