Generic
Showing 2833–2880 of 6086 results
-
Stepper Motor Drivers
TMC2100 Stepper Motor Driver, Module
SKU: 1121430- This driver has 200 steps per revolution in full step (1.8 degrees per step).
- Allowable continuous current per phase: 1.25A (RMS) or 1.77A (max)
- The maximum current in the short term for each phase: 2.5A
- Motor voltage: 5.5 to 46 V
- StealthChop mode to reduce noise
- SpreadCycle mode to increase torque
SKU: 1121430 -
-
-
Robot Kits and Parts
Robot Smart Car Chassis-Black
SKU: 781388- Smart car chassis tracing car Robot car chassis with code disk, Ideal for DIY.
- With a 4 AA battery box (batteries not included).
- It can be used for distance measurement, velocity.
- Can use with other devices to realize function of tracing, obstacle avoidance, distance testing, speed testing,
SKU: 781388 -
Digital Voltage, Current and Frequency Meter
Dual Led 0.28 Display for DC0-100V Voltage and Current Test Digital Instrument, Digital Meter Panel Amplifier Red & Red 10A
Digital Voltage, Current and Frequency MeterDual Led 0.28 Display for DC0-100V Voltage and Current Test Digital Instrument, Digital Meter Panel Amplifier Red & Red 10A
SKU: 1187604- Operating current: 10mA
- Operating voltage: DC 4.5 ~ 30V
- Minimum resolution(V): 0.1V
- Minimum resolution(A): 0.01A
- Display color: Red & Red (two-color display)
- Measure accuracy: 1%
SKU: 1187604 -
Straight Type DC BO Motors
Pair 5V 200RPM Microbit TT DC, Motor 1:48
SKU: 1121374Rated Voltage: 3~6V
Continuous No-Load Current: 150mA +/- 10%
Min. Operating Speed (3V): 90+/- 10% RPM
Min. Operating Speed (6V): 200+/- 10% RPM
Torque: 0.15Nm ~0.60Nm
Stall Torque (6V): 0.8kg.cm
Gear Ratio: 1:48SKU: 1121374 -
-
3D Printer Extruder Parts and Fans
MK10 Right Side Extrusion Gear Molded Drive Block with Bearing (1.75mm 40 Teeth)
3D Printer Extruder Parts and FansMK10 Right Side Extrusion Gear Molded Drive Block with Bearing (1.75mm 40 Teeth)
SKU: 815854- High-Quality Filament Extruder Feeder
- Direct drive extruder feeder kit
- Right-hand version
- Sharp and effective filament gear is included
- Compatible with NEMA 17 stepper motors
SKU: 815854 -
-
-
-
-
Plastic Gear Box Motor
DC Motor 1000RPM 12Volts
SKU: 356205- The metal gears have better wear and tear properties.
- The gearbox is sealed and lubricated with lithium grease and requires no maintenance.
- Although motor gives 100 RPM at 12V, the motor runs smoothly from 4V to 12V and gives the wide range of RPM, and torque.
- The shaft has a hole for better coupling.
- Operating Voltage(V): 12
- Rated Torque(kg-cm): 0.5
- Stall Torque(kg-cm): 2.0
SKU: 356205 -
-
-
-
Drone Transmitter and Receiver
2.4G 4CH Receiver Compatible with D8 Receiver w/ PWM Output
SKU: 1119195- Channel: 4CH
- Weight: 2.2g
- Resolution: 1024
- PWM Output: Yes
- Operating Voltage: 3.5-10V
- Current: 50MA
- Antenna Length: 100mm
- Control Range: >500M+
- Compatibility: Compatible with Frsky X9D (D8 Mode), XJT (D8 Mode), DJT, DFT, DHT
SKU: 1119195 -
Relay Modules
1 Channel Relay Module, 30A with Optocoupler, Isolation 5V Supports, High and Low Triger, （with Guide Rail）
Relay Modules1 Channel Relay Module, 30A with Optocoupler, Isolation 5V Supports, High and Low Triger, （with Guide Rail）
SKU: 1121227- Channel: 1 channel
- Comes with GUIDE RAIL
- Relay Voltage: 5V
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- One normally closed contact and one normally open contact
- Triode drive, increasing relay coil
SKU: 1121227 -
Operational Amplifier ICs
74LVC1G32GW,125 – 5.5V Rail-to-Rail Output Operational Amplifier 5-Pin TSSOP (Nexperia)
Operational Amplifier ICs74LVC1G32GW,125 – 5.5V Rail-to-Rail Output Operational Amplifier 5-Pin TSSOP (Nexperia)
SKU: 1072494Voltage – Supply: 1.65V ~ 5.5V
Current – Quiescent (Max): 4µA
Current – Output High, Low: 32mA, 32mA
Logic Level – Low: 0.7V ~ 0.8V
Logic Level – High: 1.7V ~ 2VSKU: 1072494 -
-
Water TDS, pH, Flow, Level and Pressure Sensor
XH-M203 12V 10A Water Level Controller Module
SKU: 1794279- Current: Operating – 200mA Relay Switch – 10A (Please note this is not the actual current that can handle the relay. we recommended up to 3A. If you are looking for higher current switching please add another high current switch with module relay.)
- Type:Â Â LED indicator for water level.
- I/O Pins: Water Level High input & Water Level Low input.
- Operating Voltage:Â AC12V DC12V.
SKU: 1794279
