Search results: “motor” – Page 12
Showing 529–576 of 1355 results
-
(ESC) Drone Speed Controller
T Motor Alpha 40A 6S Esc
SKU: 1241806- Model: ALPHA 40A
- Brand: T-motor
- Voltage: 4-6S ( 18-25.2V)
- Current: 40A
- Throttle range: 1100-1940μs
- Special core program for multi-rotor controller greatly improve throttle response
- Power by independence stabilivolt IC supply microprocessor is with better antijamming performance for stability
SKU: 1241806 -
-
(ESC) Drone Speed Controller
T Motor Flame 60A Hv Esc
SKU: 1092909- Output:Â Â Continuous 60A, Burst 80A up to 10 Secs.
- Input Voltage:Â 2-6 cells lithium battery or 5-18 cells NiCd/NIMh battery.
- BEC:Â Â Pentium-60A: 3A / 5V (Switch mode).
- Max Speed:Â 210,000rpm for 2 Poles BLM, 70,000rpm for 6 poles BLM, 35,000rpm for 12 poles BLM. (BLM: Brushless Motor)
SKU: 1092909 -
Shield for Arduino
L293D Motor Driver/Servo Shield for Arduino
SKU: 9736- 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
- 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes.
- Can run motors on 4.5VDC to 25VDC.
- Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, or interleaved stepping.
SKU: 9736 -
Stepper Motor Drivers
ULN2003A Driver Module Stepper Motor Driver
SKU: 28379- 5-12V power supply
- 4-way signal indicator
- Chip all the pins have Input leads Mounted for easy connection to use
- XH-5P socket can be connected directly 28BYJ-48 Model stepper motor
- Dimensions: 32 x 18 x 11mm (LxWxH)
- Weight: 3 gm
SKU: 28379 -
-
Advance Development Boards
Micro Bit Motor Drive Breakout Board Shield
SKU: 975802- Input Voltage：DC 6-12V
- Working current of motor drive: <= 1.2A
- Starting peak current: 2A/3.2A
- 4 motor control modes: Forward/reverse/brake/stop
- PWM frequency: 100 kHz max
- Drive Partial Working Current：≤1.2A
SKU: 975802 -
-
Cytron Motor Drivers
Cytron Maker Drive H-Bridge Motor Driver
SKU: 381588- Dual channel, Bi-directional control motor driver
- Support motor voltage from 2.5V to 9.5VDC
- Maximum current up to 1.0A continuous and 1.5A peak (<5 seconds)
- 5V Output (200mA)Â to power the controller.
- Inputs compatible with 1.8V, 3.3V and 5V logic (Arduino, Raspberry Pi, etc).
- Solid state components provide faster response time and eliminate the wear and tear of mechanical relay
- Regenerative Braking
Â
SKU: 381588 -
3D Printer Motor Drivers
MakerBase MKS A4988 Stepper Motor Driver Module
SKU: 1632932- Operating Voltage: 8V to 35V
- Continuous Current Per Phase: 1A – 2A (Max with Heat Sink)
- Logic Voltage: 3V to 5.5V
- Microstep Resolutions: Full; 1/2; 1/4; 1/8; 1/16
- Heat Sink: Included (With Adhesive Thermal Backing)
- Protection: Overcurrent, Under-Voltage Lockout, Automatic Chopping Control
- Dimensions: 15 x 20mm
SKU: 1632932 -
-
-
Pololu Motor Drivers
Pololu High-Power Stepper Motor Driver 36v4
SKU: 1607680- Inputs compatible with 1.8Â V, 3.3Â V, and 5Â V logic
- Under-voltage lockout, over-current protection, short circuit protection, and reverse-voltage protection (up to 40Â V)
- High-power: can deliver up to 4Â A continuous per phase without extra cooling (6Â A max with sufficient additional cooling)
- Highly configurable through SPI interface
- Optional STEP/DIR control pins (stepping can also be controlled through SPI interface alone)
SKU: 1607680 -
-
-
Pololu Motor Drivers
Pololu DRV8834 Low-Voltage Stepper Motor Driver Carrier
SKU: 1607671- Built-in regulator (no external logic voltage supply needed)
- Short-to-ground, short-to-supply, and shorted-load protection
- 4-layer, 2Â oz copper PCB for improved heat dissipation
- Exposed solderable ground pad below the driver IC on the bottom of the PCB
- Simple step and direction control interface
SKU: 1607671 -
-
IR and RF Transmitters and Receivers
SmartElex Wireless Remote Control with NRF Transceiver and Motor Driver
IR and RF Transmitters and ReceiversSmartElex Wireless Remote Control with NRF Transceiver and Motor Driver
SKU: R1231941. Transmitter & Receiver comes Pre-Bind.
2. It uses 2.4GHz global open ISM band, with license-free.
3. Operating Range: 1Km.
4. Antenna Gain (peak): 2Dbi.
5. Transmit power is greater than +20 dBm.
Receiver:
1. Output current: 1.2 A continuous (2 A peak) per motor.
2. Under-voltage lockout and protection against over-current and over-temperature.SKU: R123194 -
N20 Metal Gear Motors
N20-6V-40 Rpm Micro Metal Gear Motor
SKU: 268861- This is a DC Mini Metal Gear Motor, ideal for making robots
- Lightweight, high torque and low RPM.
- Fine craftsmanship, durable, not easy to wear.
- With excellent stall characteristics, can climb hills easily.
- You can also easily mount a wheel on the motor’s output shaft.
SKU: 268861 -
-
