Shield for Arduino
Showing 49–60 of 60 results
-
Shield for Arduino
PS2 Controller Starter Kit
SKU: 7438- Stable 5V powered, low current consumption, less than 150mA.
- 1 standard PS2 controller socket.
- Communicate with host microcontroller through 5V TTLÂ UART.
- Simple inquiry command and button status feedback for the host process.
- Vibrator motor is controllable.
- Wired or wireless PS2 controller is fully compatible.
- A small LED as the indicator for communication between SKPS and PS2 controller.
SKU: 7438 -
Shield for Arduino
Colorduino LED RGB Dot Matrix Driver Board with 5mm 8*8 RGB LED for Arduino
SKU: 330167- 8bits colors support with 6bits correction for each color in every dots
- Hardware 16MHz PWM support
- 24 constant current channels of 100mA each
- Current Consumption(Except LED matrix): 20mA typical (40mA maximum)
- Drive current(Every channel):Â 500mA
- Drive current(Every dot) :Â 58mA
SKU: 330167 -
Shield for Arduino
Cytron Easy MP3 Shield
SKU: 7982-
Onboard high-quality MP3 decoder.
-
Onboard dual channel/Stereo 3W differential audio amplifier for an external speaker.
- A MicroSD status LED.
-
Onboard stereo 3.5mm audio jack socket for earphones.
-
Onboard microSD socket for MP3 audio files storage.
-
The interface from Arduino, UART, selectable to use soft serial.
-
Stackable side headers.
- Supply voltage: 5V.
SKU: 7982 -
-
-
Shield for Arduino
SeeedStudio Grove Beginner Kit for Arduino
SKU: 601890- Operating voltage: 5 V
- Tutorials for guidance
- Fully compatible with Arduino UNO
- High performance, low power 8 bit ATmega328 MU microcontroller
- Serial converter CP2102N chip (to communicate the Seeeduino with a computer by using a micro-USB cable)
- 2 on-board Grove connectors
- 14 Digital I/O Pins (6 PWM outputs)
- 6 Analog inputs
- ISP header
- Arduino UNO-R3 shield compatible
- Micro USB programming and power supply
- Supports Windows, Mac OS, and Linux
SKU: 601890 -
-
LORA Module, Shield for Arduino
Wireless Transmitter 915Mhz, Lora Shield for Leonardo,, UNO, Mega2560,, Duemilanove, Due
LORA Module, Shield for ArduinoWireless Transmitter 915Mhz, Lora Shield for Leonardo,, UNO, Mega2560,, Duemilanove, Due
SKU: 1121438- 168 dB maximum link budget.
- +20 dBm – 100 mW constant RF output vs.
- +14 dBm high-efficiency PA.
- Programmable bit rate up to 300 kbps.
- High sensitivity: down to -148 dBm.
- Bullet-proof front end: IIP3 = -12.5 dBm.
- Excellent blocking immunity.
- Low RX current of 10.3 mA, 200 nA register retention.
- Fully integrated synthesizer with a resolution of 61 Hz.
- FSK, GFSK, MSK, GMSK, LoRaTM and OOK modulation.
- Built-in bit synchronizer for clock recovery.
- Preamble detection.
- 127 dB Dynamic Range RSSI.
SKU: 1121438 -
-
Shield for Arduino
SHIELD-EKG-EMG
SKU: 6320- Stackable connectors – up to 6 channels can be stacked and wired to A0-A6 analogue inputs
- Calibration signal generation by D4/D9 digital output
- Precise trimmer potentiometer for calibration (all boards are shipped completely assembled, tested and calibrated so that you don’t have to do this unless you want to see how things works)
- Input connector for standard or active electrodes
- Works with both 3.3V and 5V Arduino boards
SKU: 6320 -
LORA Module, Shield for Arduino
LoRa Shield for Arduino V95
SKU: 127766- Compatible with 3.3v or 5v I/O Arduino Board.
- Frequency Band: 915MHz/868 MHZ/433 MHZ (Pre-configure in a factory)
- Low power consumption
- Compatible with Arduino Leonardo, Uno, Mega, DUE
- External Antenna via I-Pex connector
SKU: 127766 -
-
Shield for Arduino
Arduino Opta WiFi AFX00002
SKU: 1723289- Input    : 8x configurable digital / analog (0-10V) input
- Processor: STM32H747XI Dual ARM® Cortex®:
Cortex -M7 core up to 480 MHz
Cortex -M4 core up to 240 MHz - Connectivity: Support 10/100 Ethernet (TCP/IP or Modbus TCP)
USB-C
Wi-Fi + Bluetooth® Low Energy
RS485 half duplex
SKU: 1723289