Categories

Brushed DC Motor Drivers

  • 16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi

    SKU: 43740
     350.00

    (inc GST)

    ₹ 296.61 (+18% GST extra)

    1. Adjustable frequency PWM up to about 1.6 KHz
    2. 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
    3. Configurable push-pull or an open-drain output
    4. The output enable pin to quickly disable all the outputs
    5. Terminal block for power input
    6. Reverse polarity protection on the terminal block input
    7. Green power-good LED
    Read more
  • 20A PWM DC Motor Speed Regulator Module (9V, 12V, 24V, 36V, 48V, 60V)

    SKU: 51649
     590.00

    (inc GST)

    ₹ 500 (+18% GST extra)

    1. Adjustable speed range: 0%-100%.
    2. Speed adjustment way: Potentiometer.
    3. Output voltage: Linear under load.
    4. Speed control type: Basins.
    5. Output voltage: Load Linear
    6. Type: Adjusting flow
    7. The motor running condition adjustment: Forward  / Stop / Reverse
    Read more
  • 5-36v Switch Drive High-power MOSFET Trigger Module

    SKU: 52812
     150.00

    (inc GST)

    ₹ 127.12 (+18% GST extra)

    This 5-36v Switch Drive High-power MOSFET Trigger Module can control the output of power equipment, motors, light bulbs, LED lights, DC motors, micro-pumps,  solenoid valves, PWM, motor speed control, lamp brightness. etc.

    Read more
  • Cytron 10 A Switch Control Potentiometer DC Motor Driver (MD10POT)

    SKU: 234226
     949.00

    (inc GST)

    ₹ 804.24 (+18% GST extra)

    The MD10-POT control circuit is designed to enable the speed to be controlled via a potentiometer (10K Ohm) which is included in the package. It does not work with analog voltage from an external controller  The 3-way rocker switch is used for start/stop and direction control.

    Add to cart
  • Cytron 10A Dual Channel DC Motor Driver Shield for Arduino Uno

    SKU: 497899
     1,720.00

    (inc GST)

    1. Bidirectional control for two brushed DC motor.
    2. Control one unipolar/bipolar stepper motor.
    3. Buck regulator to produce 5V output (500mA max).
    4. Buttons for quick testing.
    5. LEDs for motor output state.
    Read more
  • Cytron 25A 7V-58V DC motor driver with Switch and Potentiometer Control (MD25HV POT)

    SKU: 497900
     3,854.00

    (inc GST)

    1. Bidirectional control for one brushed DC motor.
    2. Maximum Motor Current: 25A continuous, 60A peak.
    3. 5V output for the host controller (250mA max).
    4. Buttons for quick testing.
    5. PWM frequency up to 40kHz.
    6. Dual Input Mode: PWM/DIR or Potentiometer/Switch Input.
    Add to cart
  • Cytron Driver HAT-MDD10

    SKU: 29670
     1,890.00

    (inc GST)

    ₹ 1601.69 (+18% GST extra)

    1. Support motor voltage ranges from 6VDC to 24VDC.
    2. Onboard the test button for manual control of the motor.
    3. Every channel output built with LED indicator.
    4. Current limiting at 30A.
    5. Operating Voltage(VDC): 6 to 24
    6. Peak Current (A): 30 (10 seconds)
    7. Continuous Current (A): 10
    8. No. of Channels: 2
    9. Operating Modes: PWM (Lock-Antiphase and Sign-Magnitude): Yes, UART: No, Analog:No, RC Servo Signal: No
    Add to cart
  • Cytron Dual channel 10A Motor Driver UNO Robot Controller

    SKU: 49866
     2,510.00

    (inc GST)

    ₹ 2127.12 (+18% GST extra)

    1. Onboard 1A (maximum) 5V voltage regulator.
    2. Onboard 500mA (maximum) 3.3V voltage regulator.
    3. 0-5V digital outputs with 3.3V compatible inputs.
    4. 14 Digital I/O Pins (6 PWM outputs).(4 pin used for Motor driver)
    5. 6 Analog Inputs (Can be digital I/O too).
    6. Maximum current up to 10A continuous and 30A Peak.
    7. ISP 6-pin Header.
    8. 32k Flash Memory.
    9. 16MHz Clock Speed.
    10. R3 Shield Compatible.
    Add to cart
  • Cytron FD04A 4-Channel Motor Driver

    SKU: 16010
     2,362.00

    (inc GST)

    ₹ 2001.69 (+18% GST extra)

    1. Industrial grade PCB.
    2. Vmotor: 7 V to 25 V DC.
    3. Each component is soldered properly and tested.
    4. Able to drive 4 DC motor at 2.5A (peak), 1.5A continuously.
    5. 2 LEDs as a direction indicator for each motor.
    6. 1 LED as a power indicator.
    7. A pluggable connector for more user-friendly design.
    8. Fully compatible with Cytron DIY project, Flexibot – Using Transwheel (PR19).
    Read more
  • CYTRON SMART DRIVE MDDS30 DUAL 30A (80A Peak)

    SKU: 29672
     5,490.00

    (inc GST)

    ₹ 4652.54 (+18% GST extra)

    1. Battery low voltage indicator.
    2. Battery over voltage indicator.
    3. Thermal protection.
    4. Current limit protection.
    5. Bi-directional control for dual brushed DC motor.
    6. Support motor voltage from 7V to 35VDC.
    7. Dimension: 103 x 97 x 40 (LxWxH) mm.
    Read more
  • Cytron SmartDriveDuo-60 MDDS60 60A (100A peak)

    SKU: 8014
     12,064.00

    (inc GST)

    ₹ 10223.73 (+18% GST extra)

    1. DC Brush motor Driver, not for brushless motor
    2. Input Voltage (Motor): 7 – 45VDC
    3. Two manual/test buttons for each channel.
    4. Two output indicator LEDs for each channel.
    5. Suitable for combat or sumo robot.
    6. Battery Low Voltage Monitoring Mode
    Read more
  • DC Motor PWM Speed Regulator 1.8V, 3V, 5V, 6V, 12V-2A speed control switch function

    SKU: 12267
     240.00

    (inc GST)

    ₹ 203.39 (+18% GST extra)

    1. Input supply voltage: 1.8V- 15V DC.
    2. The maximum output power: 30W
    3. Output current : 2A(Max).
    4. With resettable fuse.
    5. Equipped with LED indicator.
    6. Potentiometer with switch function for PWM adjustment.
    Add to cart
  • Double BTS7960 43A H-Bridge High-Power Stepper Motor Driver Module

    SKU: 456144
     899.00

    (inc GST)

    ₹ 761.86 (+18% GST extra)

    1. Input voltage(V): 6 – 27.
    2. Maximum current(A): 43.
    3. Input level(V): 3.3 – 5.
    4. Duty cycle: 0 – 100%.
    5. Path resistance: 16 mΩ at 25°C.
    6. Low quiescent current: 7 µA at 25°C.
    Read more
  • Dual Monster Moto Shield VNH2SP30 DC Motor Driver 2x14A (Peak 30A)

    SKU: 28535
     699.00

    (inc GST)

    ₹ 592.37 (+18% GST extra)

    1. Voltage Max: 16V
    2. Maximum current rating: 30 A
    3. Practical Continuous Current: 14 A
    4. Current sensing available to Arduino analog pin
    5. MOSFET on-resistance: 19 mΩ (per leg)
    6. Maximum PWM frequency: 20 kHz
    7. Thermal Shutdown
    8. Undervoltage and Overvoltage shutdown.
    Add to cart
  • Enhanced Cytron 40Amp DC Motor Driver (Peak 80amp) MDS40B

    SKU: 11648
     5,239.00

    (inc GST)

    ₹ 4439.83 (+18% GST extra)

    1. Bi-directional control for a single brushed DC motor.
    2. Support motor from 10V to 45V.
    3. Maximum current up to 80A peak, reduce to 40A gradually according to temperature.
    4. 16 KHz switching frequency for quiet operation.
    5. NO Reverse polarity protection.
    6. Protection of overvoltage.
    Add to cart
  • IRF520 MOSFET Driver Module for Arduino ARM Raspberry pi

    SKU: 44050
     110.00

    (inc GST)

    ₹ 93.22 (+18% GST extra)

    1. Voltage: 3.3 – 5V.
    2. Ports: Digital Level.
    3. Output load voltage: 0-24 V.
    4. Output load current: <5A (1A above need to add heat sink).
    5. Platform: Arduino, MCU, ARM, raspberry pi.
    6. Using original IRF520 Power MOS, you can adjust the output PWM
    Add to cart
  • Kangaroo X2 Motion Controller

    SKU: 15839
     1,879.00

    (inc GST)

    ₹ 1592.37 (+18% GST extra)

    1. Model: Kangaroo x2
    2. 2 channel self-tuning PID controller
    3. Position or speed control
    4. Quadrature encoder feedback or potentiometer feedback
    5. Support for limit switches and mechanical stops
    6. Analog, R/C, and serial inputs
    Add to cart
  • L293D Motor Driver/Servo Shield for Arduino

    SKU: 9736
     179.00

    (inc GST)

    ₹ 151.69 (+18% GST extra)

    1. 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
    2. 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes.
    3. Can run motors on 4.5VDC to 25VDC.
    4. Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
    5. Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
    6. Pull down resistors keep motors disabled during power-up
    7. Big terminal block connectors to easily hook up wires (18-26AWG) and power
    8. 2-pin terminal block and jumper to connect external power, for separate logic/motor supplies
    Read more
  • L298N 2A Based Motor Driver Module – Good Quality

    SKU: 43821
     159.00

    (inc GST)

    ₹ 134.75 (+18% GST extra)

    1. Current Sense for each motor.
    2. Heatsink for better performance.
    3. Power-On LED indicator.
    4. Double H bridge Drive Chip: L298N.
    5. Operating Voltage(VDC): 5~35
    6. Peak Current (A): 2
    7. Continuous Current (A): 0-36mA
    8. No. of Channels: 2
    9. Over-Current Protection (A): Yes
    10. Thermal Protection: Yes
    Add to cart
  • L298N Dual H Bridge DC/Stepper Motor Driver Controller Module

    SKU: 51971
     199.00

    (inc GST)

    ₹ 168.64 (+18% GST extra)

    1. Driver chip: L298N Dual H Bridge
    2. Supply voltage: VMS 5V – 35V
    3. Peak current IO: 2A per bridge
    4. Max power consumption: 20W
    5. Provides 4 LEDs that reflect the state of the control logic
    6. Independent direction, speed, and braking for each motor
    Read more
  • MD13S 13Amp DC Motor Driver – GROVE Compatible

    SKU: 24027
     891.00

    (inc GST)

    ₹ 755.08 (+18% GST extra)

    1. Support motor voltage ranges from  6V to 30V
    2. Maximum current up to 13A continuous and 30A peak (10 seconds).
    3. GROVE compatible
    4. 3.3V and 5V logic level input.
    5. SMD compatible
    6. Peak Current (A): 30 (10 seconds)
    7. Continuous Current (A): 1
    8. No. of Channels: 1
    Add to cart
  • Monster Moto Shield VNH2SP30 Motor Driver 14A (Peak 30A)

    SKU: 28546
     349.00

    (inc GST)

    ₹ 295.76 (+18% GST extra)

    1. Voltage Max: 16V
    2. Maximum current rating: 30 A
    3. Practical Continuous Current: 14 A
    4. Current sensing available to Arduino analog pin
    5. MOSFET on-resistance: 19 mΩ (per leg)
    6. Maximum PWM frequency: 20 kHz
    7. Thermal Shutdown
    8. Undervoltage and Overvoltage shutdown.
    Add to cart
  • Motor Driver TB6612FNG Module Performance Ultra Small Volume 3 PI Matching Performance Ultra L298N

    SKU: 43846
     199.00

    (inc GST)

    ₹ 168.64 (+18% GST extra)

    1. CW/CCW/short break/stop motor control modes
    2. Built-in thermal shutdown circuit and a low voltage detecting circuit
    3. Standby control to save power
    4. CW/CCW/short brake/stop motor control modes
    5. Operating Voltage(VDC): 15
    6. Peak Current (A): 3.2
    7. Continuous Current (A): 1.2
    8. No. of Channels: 1
    Add to cart
  • SmartElex 10D DC Motor Driver HAT for Raspberry Pi

    SKU: 128421
     1,189.00

    (inc GST)

    ₹ 1007.63 (+18% GST extra)

    1. Wide 6V to 28V motor Operating Voltage.
    2. Continuous 10A maximum current without Heatsink and 30A peak current for 10 Seconds.
    3. Two brushed DC motor Bidirectional control.
    4. Current limiting at 35A.
    5. PWM frequency up to 32KHz
    6. Support TTL PWM from the microcontroller
    7. Internal thermal shutdown
    8. Under-voltage lockout
    9. PWM and direction controlled driving of four externally powered NMOS transistors
    10. 3V and 5V logic level input.
    Add to cart
  • SmartElex 10D Motor Driver for Arduino UNO

    SKU: 198176
     1,790.00

    (inc GST)

    ₹ 1516.95 (+18% GST extra)

    1. Onboard 5V 3A Buck Converter.
    2. Continuous 10A maximum current without Heatsink and 30A peak current for 10
    3. Two brushed DC motor Bidirectional control.
    4. Current limiting at 35A.
    5. PWM and direction controlled driving of four externally powered NMOS transistors
    Add to cart
  • SmartElex 10S DC Motor Driver HAT

    SKU: 103711
     749.00

    (inc GST)

    ₹ 634.75 (+18% GST extra)

    1. Wide 6V to 28V motor Operating Voltage.
    2. One brushed DC motor Bidirectional control.
    3. Current limiting at 35A.
    4. PWM frequency up to 32KHz
    5. Support TTL PWM from the microcontroller
    6. Internal thermal shutdown
    7. Under-voltage lockout
    Add to cart
  • SmartElex 15D Dual Channel DC Motor Driver

    SKU: 55900
     1,449.00

    (inc GST)

    ₹ 1227.97 (+18% GST extra)

    1. Supply Voltage: 6.8-30 VDC.
    2. Continuous Current: 13 Amp.
    3. PWM Frequency: 20 KHz.
    4. Current limiting at 30A.
    5. 3V and 5V logic level input.
    Add to cart
  • SmartElex 15D Smart Motor Driver

    SKU: 199307
     1,980.00

    (inc GST)

    ₹ 1677.97 (+18% GST extra)

    1. Support motor voltage from 7V to 28V.
    2. Onboard Low, Internal resistance MOSFETs are switched at 16 KHz frequency.
    3. Overcurrent and Thermal protection.
    4. Multiple input modes: RC, Analog, PWM, Serial Packetized.
    5. On board push buttons for test and manual operation.
    Add to cart
  • SmartElex 15S DC Motor Driver 15A (30A Peak)

    SKU: 47993
     750.00

    (inc GST)

    ₹ 635.59 (+18% GST extra)

    1. Supply Voltage: 6.8-30 VDC.
    2. Continuous Current: 15 Amp.
    3. PWM Frequency: 20 KHz.
    4. Max Peak current: 30 Amp(For 10 Seconds).
    5. One brushed DC motor Bidirectional control.
    Add to cart
  • SmartElex 30D Dual Channel 30A Smart DC Motor Driver

    SKU: 77719
     3,799.00

    (inc GST)

    ₹ 3219.49 (+18% GST extra)

    1. Supplying 30 amps continuous with peak currents up to 85 amps (2 Sec) per channel.
    2. Support motor voltage from 7V to 30V.
    3. Onboard Low Internal resistance MOSFETs are switched at 16 KHz frequency.
    4. Overcurrent protection and indication.
    5. Thermal protection.
    6. Multiple input modes: RC, Analog, PWM, Serial Packetized.
    7. On board push buttons for test and manual operation.
    Add to cart
  • SmartElex Battle Relay

    SKU: 55640
     590.00

    (inc GST)

    ₹ 500 (+18% GST extra)

    1. Max current and voltage:
      • 10A @ 125VAC
      • 7A @ 240VAC
    2. Relay resistance: 100 mΩ max
    3. 4.8V to 5.2V operating voltage
    4. 30mA typical draw from receiver
    5. Powerful auxiliary weapons control in RC combat.
    6. Glow plugs control in RC nitro vehicles.
    Add to cart
  • SmartElex Dual Channel Battle Relay

    SKU: 74971
     990.00

    (inc GST)

    ₹ 838.98 (+18% GST extra)

    1. Max current and voltage:
      • 10A @ 120VAC
      • 7A @ 250VAC
      • 10A @ 24VDC
    2. Relay resistance: 100 mΩ max
    3. Module operating voltage: 4.8V to 5.2V
    4. 30mA typical draw from receiver
    5. Powerful auxiliary weapons control in RC combat.
    6. Glow plugs control in RC nitro vehicles.
    Add to cart
  • SmartElex L298N Motor Driver with onboard Arduino Uno + USB Cable

    SKU: 599414
     849.00

    (inc GST)

    1. 5 mm standard DC plug-in jack for Input supply
    2. On-Board Arduino UNO with USB Port
    3. On-Board DC motor Driver L298N.
    4. On-board 5V 3A SMPS circuit.
    5. On-Board power supply on-off switch
    Add to cart
  • SmartElex L298N Motor Driver with Onboard Arduino Uno.

    SKU: 451833
     799.00

    (inc GST)

    1. 5 mm standard DC plug-in jack for Input supply
    2. On-Board Arduino UNO with USB Port
    3. On-Board DC motor Driver L298N.
    4. On-board 5V 3A SMPS circuit.
    5. On-Board power supply on-off switch
    Add to cart
  • BattleSwitch radio controlled 10A relay (Dimension Engineering)

    SKU: 6314
     1,984.00

    (inc GST)

    ₹ 1681.36 (+18% GST extra)

    1. 30mA typical draw from receiver
    2. 12-inch servo pigtail
    3. Max relay voltage: 240VAC
    4. Max relay current: 10A @ 28VDC, 12A @ 120VAC, 10A @ 240VAC.
    5. Relay resistance: 100 mΩ max
    6. operating voltage: 3.5V to 5.5V (on servo pigtail)
    Add to cart
  • L298N Based Motor Driver Module – 2A

    SKU: 5828
     148

    (inc GST)

    ₹ 125.42 (+18% GST extra)

    1. Logical voltage: 5V
    2. Drive voltage: 5V-35V
    3. Logical current: 0-36mA
    4. Drive current: 2A (MAX single bridge)
    5. Max power: 25W
    6. Dimensions: 44 x 44 x 28 (LxWxH)mm
    7. Weight: 26 gm
    Read more
  • L293D Motor Driver Module

    SKU: 5825
     119.00

    (inc GST)

    ₹ 100.85 (+18% GST extra)

    1. The driver two holes of 3 mm dia.
    2. Male burg-stick connectors for supply, ground and input connection.
    3. Screw terminal connectors for easy motor connection.
    4. High noise immunity inputs.
    5. Operating Voltage(VDC): 4.5 to 12
    6. Peak Current (A): 600 mA
    7. No. of Channels: 1
    Add to cart
  • Battle Switch (RCSwitch10)

    SKU: 4706
     1,018.00

    (inc GST)

    ₹ 862.71 (+18% GST extra)

    1. This is a Single Pole Double Throw(SPDT) type of relay
    2. Purposefully designed for RC Applications
    3. Max. AC voltage: 250V
    4. Max. DC voltage: 30VDC
    5. Max current: 10A
    Add to cart
  • Sabertooth Dual 60A Motor Driver

    SKU: 4704
     15,645.00

    (inc GST)

    ₹ 13258.47 (+18% GST extra)

    1. 60A continuous, 120A peak per channel
    2. 6-30V nominal, 33.6V absolute maximum
    3. Synchronous regenerative drive
    4. Ultra-sonic switching frequency
    5. Thermal and overcurrent protection
    6. Lithium protection mode
    Add to cart
  • Sabertooth Dual 32A Motor Driver

    SKU: 4702
     9,439.00

    (inc GST)

    ₹ 7999.15 (+18% GST extra)

    1. 32A continuous, 64A peak per channel
    2. 6-30V nominal, 33.6V absolute maximum
    3. Synchronous regenerative drive
    4. Ultrasonic 30 kHz switching frequency
    5. Thermal and overcurrent protection
    6. Battery protection mode
    7. USB control and monitoring
    8. USB serial converter mode for Kangaroo x2
    9. Configurable current limiting
    10. Custom user modes
    11. 12-bit motor outputs
    Add to cart
  • Sabertooth Dual 25A Motor Driver

    SKU: 4698
     9,082.00

    (inc GST)

    ₹ 7696.61 (+18% GST extra)

    1. 25A continuous, 50A peak per channel
      6-30V nominal, 33.6V absolute maximum
    2. Synchronous regenerative drive
    3. Ultra-sonic switching frequency
    4. Thermal and overcurrent protection
    5. Lithium protection mode
    6. Input modes: Analog, R/C, simplified serial, packetized serial
    Add to cart
  • Sabertooth Dual 12A Motor Driver for R/C

    SKU: 4695
     4,504.00

    (inc GST)

    ₹ 3816.95 (+18% GST extra)

    1. Synchronous regenerative drive
    2. Ultra-sonic switching frequency
    3. Thermal and overcurrent protection
    4. Lithium protection mode
    5. Dual motor driver
    6. Ultra-sonic switching frequency
    7. 1 Amp Switching BEC
    Add to cart
  • Sabertooth Dual 12A Motor Driver

    SKU: 4692
     5,554.00

    (inc GST)

    ₹ 4706.78 (+18% GST extra)

    1. 12A continuous, 25A peak per channel Up to 24V in
    2. Synchronous regenerative drive
    3. Ultra-sonic switching frequency
    4. Thermal and overcurrent protection
    5. Lithium protection mode
    6. Peak Current (A): 25A
    7. Continuous Current (A): 12
    8. Operating Voltage(VDC): 18 to 24V
    9. No. of Channels: 2
    Add to cart
  • Sabertooth Dual 5A Motor Driver for R/C

    SKU: 4689
     4,189.00

    (inc GST)

    ₹ 3550 (+18% GST extra)

    1. Operating Voltage(VDC): 6-18
    2. Peak Current (A): 10
    3. Continuous Current (A): 5
    4. No. of Channels: 2
    5. Synchronous regenerative drive
    6. Ultra-sonic switching frequency
    7. Thermal and overcurrent protection
    8. Lithium protection mode-compatible with: 6-12 cell NiMH or NiCd, 2s-4s LiPo, 6V or 12V lead acid (not 18+V lead acid!)
    Add to cart
  • Sabertooth Dual 5A Motor Driver

    SKU: 4686
     4,189.00

    (inc GST)

    ₹ 3550 (+18% GST extra)

    1. Input Voltage: 6V to 18V
    2. Compatible with: 6-12 cell NiMH or NiCd, 2s-4s LiPo
    3. 5A continuous per channel, 10A peak
    4. Synchronous regenerative drive
    5. Ultra-sonic switching frequency
    6. Thermal and overcurrent protection
    7. Lithium protection mode
    Add to cart
  • Cytron SmartDriveDuo-10 MDDS10 DC MOTOR DRIVER

    SKU: 4565
     3,937.00

    (inc GST)

    ₹ 3336.44 (+18% GST extra)

     

    1. Single power operation
    2. Dual Channels means it can drive two brush motor independently, or mixed.
    3. Support Signed magnitude and Locked Anti-phase in PWM mode.
    4. Two manual/test buttons for each channel.
    5. Two output indicator LEDs for each channel.
    6. Power, Error indicator, RUN status (Left and Right) LEDs
    7. On board reset button to restart the MCU after changing operation mode.
    8. Operating modes: RC (RC servo signal), Analog, PWM, simplified and packetized UART.
    Add to cart
  • 10A Motor Driver Shield – MD10

    SKU: 3408
     1,564.00

    (inc GST)

    ₹ 1325.42 (+18% GST extra)

    1. Bi-directional control of 1 brushed DC motor.
    2. Support motor voltage ranges from 7V to 25V, .
    3. Maximum current up to 10A continuous and 15A peak (10 seconds).
    4. Solid state components provide faster response time and eliminate the wear and tear of a mechanical relay.
    5. Fully NMOS H-Bridge for better efficiency and no heat sink is required.
    6. Speed control PWM frequency up to 10KHz.
    7. Selectable digital pins for PWM and DIR.
    Read more
  • Cytron Dual Channel Enhanced 13Amp DC Motor Driver 30A Peak MDD10A

    SKU: 3405
     1,890.00

    (inc GST)

    ₹ 1601.69 (+18% GST extra)

    1. Bi-directional control of 2 brushed DC motor.
    2. Support motor voltage ranges from 5V to 25V.
    3. Maximum current up to 13A continuous and 30A peak (10 seconds) for each channel.
    4. Solid state components provide faster response time and eliminate the wear and tear of the mechanical relay.
    5. Fully NMOS H-Bridge for better efficiency and no heat sink is required.
    Read more
  • Cytron MDS160A SmartDrive160 160AMP Dc Motor Driver (Peak 190Amp)

    SKU: 2784
     19,845.00

    (inc GST)

    ₹ 16817.8 (+18% GST extra)

    1. Bi-directional control for a single brushed DC motor.
    2. Support input voltage from 8V to 28V.
    3. Maximum current up to 190A peak (1 minute), 175A (2 minutes) or 160A (continuously).
    4. 16 KHz switching frequency for quiet operation.
    5. LiPo battery low voltage warning.
    6. Thermal protection.
    Read more
  • Cytron Enhanced 13Amp DC Motor Driver 30A peak (10 seconds) MD10C

    SKU: 2777
     1,039.00

    (inc GST)

    ₹ 880.51 (+18% GST extra)

    1. Bi-directional control of 1 brushed DC motor.
    2. Support motor voltage ranges from  5V to 25V.
    3. Maximum current up to 13A continuous and 30A peak (10 seconds).
    4. 3.3V and 5V logic level input.
    5. Solid state components provide faster response time and eliminate the wear and tear of the mechanical relay.
    6. Fully NMOS H-Bridge for better efficiency and no heat sink is required.
    Add to cart
  • Cytron 30Amp DC Motor Driver (Peak 80Amp) MD30C R2

    SKU: 2774
     3,045.00

    (inc GST)

    ₹ 2580.51 (+18% GST extra)

    1. Bi-directional control of 1 brushed DC motor.
    2. Motor Voltage: 5V – 25V.
    3. Maximum Current: 80A peak (1 second), 30A continuously.
    4. Reverse polarity protection.
    5. 3.3V and 5V logic level input.
    6. Fully NMOS H-Bridge for better efficiency and no heat sink is required.
    Add to cart