SmartElex RLS-06 Analog & Digital Line Sensor Array

(2 customer reviews)
Availability:

In stock


SKU: 63761
  1. Operating voltage: 4.5V to 5.0 V
  2. Output format: 6 Analog and Digital voltages.
  3. Optimal sensing distance: 0.125″ (3 mm).
  4. Potentiometer to adjust the sensitivity of the individual sensors.
  5. The module is a convenient carrier for six IR emitter and receiver pairs evenly paced.
  6. Great useful in building fast line following and grid navigating robots
  7. Comes with easy to use digital outputs that can be connected directly to microcontrollers

 350.00

(inc GST)

₹ 296.61 (+18% GST extra)

In stock

Select below products to add together

8 Pin JST XH 2.54mm Pitch Plug and Socket with Cable - 3 Pcs. ₹ 75
8 pin JST XH, 2.5mm, Both side Female (Pack of 2) ₹ 69
Male to Female Jumper Wires 40 Pin 30cm ₹ 63

New Price: ₹ 350


Purchase this product now and earn 4 Robu Points!


For bulk and B2B enquiries kindly mail us at [email protected]
Brand: SmartElex
Category: Line Sensor
Tags: Line Sensor, line follower, array, IR, SmartElex, Photodiode, Photoresistor, IR Emitter, IR Sensor, Line following Robot, TCRT5000

This SmartElex RLS-06 Analog & Digital Line Sensor Array has 6 IR LED/phototransistor pairs, making it a great detector for a line-following robot.  Each sensor has its own digital and analog output. potentiometer to adjust the sensitivity of the individual sensors.

The TCRT5000 reflectance sensors array is intended as a line sensor, but it can be used as a general-purpose proximity or reflectance sensor. The module is a convenient carrier for eight IR emitter and receiver (phototransistor) pairs evenly spaced at intervals.

Each phototransistor is connected to a pull-up resistor to form a voltage divider that produces an analog voltage output between 0 V and VIN (which is typically 5 V) as a function of the reflected IR. The lower output voltage is an indication of greater reflection.

The outputs are all independent, but the LEDs are arranged in pairs to halve current consumption. The LEDs are controlled by a MOSFET with a gate normally pulled high, allowing the LEDs to be turned off by setting the MOSFET gate to a low voltage. Turning the LEDs off might be advantageous for limiting power consumption when the sensors are not in use or for varying the effective brightness of the LEDs through PWM control.

Smartelex Rls-06 Analog &Amp; Digital Line Sensor Array

The LED current-limiting resistors for 5 V operation are arranged in two stages; this allows a simple bypass of one stage to enable operation at 3.3 V. The LED current is approximately 20-25 mA, making the total board consumption just under 100 mA. The schematic diagram of the module is shown above.


Features :

  1. Potentiometer to adjust the sensitivity of the individual sensors.
  2. The module is a convenient carrier for six IR emitter and receiver pairs evenly paced.
  3. Uses 6 sensors for best resolution
  4. Great useful in building fast line following and grid navigating robots
  5. Comes with easy to use digital outputs that can be connected directly to microcontrollers
  6. The array has mounting holes of 3mm diameter for easy mounting

Package Includes:

1 x SmartElex RLS-06 Analog & Digital Line Sensor Array

Brand

SmartElex

Operating Voltage (VDC)

4.5 ~ 5.0

Supply Current (A)

0.1

Output Format

6 Analog and Digital Voltages

Optimal Sensing Distance(mm)

3

Max. Sensing Distance(mm)

6

Mounting Hole(mm)

3

Length (mm)

34

Width (mm)

70

Height (mm)

10

Weight (gm)

14

Shipment Weight

0.018 kg

Shipment Dimensions

5 × 4 × 3 cm

6 Months Warranty

This item is covered with a supplier warranty of 6 months from the time of delivery against manufacturing defects only. This is a quality product from the original manufacturer. Only manufacturing defects are covered under this warranty. Reimbursement or replacement will be done against manufacturing defects.


What voids the warranty:

If the product is subject to misuse, tampering, static discharge, accident, water or fire damage, use of chemicals & soldered or altered in any way.

Based on 2 reviews

5.0 overall
2
0
0
0
0

Add a review

  1. Kaushal pawar (verified owner)

    This sensor is good for basic line follower. And this sensor is affordable.
    For advance Line follower i don’t recommend this sensor

    Kaushal pawar

  2. [email protected]

    very nice

    [email protected]

Questions and answers of the customers

  1. 0 votes
    Q what is the distance between two sensor ??? answer now
    Asked by avinash kumar on October 10, 2019 1:46 am
    A

    The distance between the two IR sensor is 15mm.... Read more

Only registered users are eligible to enter questions
Country Of Origin: INDIA

You may also like…