SmartElex
-
SmartElex RLS05 Line Follower Sensor Module
₹ 595.00(inc GST)
₹ 504.24 (+18% GST extra)
- Operating Voltage Range: 9~12V
- Maximum Operating Current: 130 mA
- Optimal Sensing Distance: 0.125″ (3 mm).
- Fast response time
- High sensitivity
- 5 Analog and 5 Digital Output signals with Respective LED.
- Each IR has indicating LED (D0-D4).
- Available SPI and Serial communication Pins.
-
SmartElex RLS-08 Analog & Digital Line Sensor Array
₹ 445.00(inc GST)
₹ 377.12 (+18% GST extra)
- Operating voltage: 4.5V to 5.0 V
- Supply current: 150 mA
- Output format: 8 Analog and Digital voltages.
- Optimal sensing distance: 3 mm.
- Maximum recommended sensing distance: 6 mm
- Potentiometer to adjust the sensitivity of the individual sensors.
- Uses 8 sensors for best resolution
- Comes with easy to use digital outputs that can be connected directly to microcontrollers
-
SmartElex RLS-06 Analog & Digital Line Sensor Array
₹ 279.00(inc GST)
₹ 236.44 (+18% GST extra)
- Operating voltage: 4.5V to 5.0 V
- Output format: 6 Analog and Digital voltages.
- Optimal sensing distance: 0.125″ (3 mm).
- Potentiometer to adjust the sensitivity of the individual sensors.
- The module is a convenient carrier for six IR emitter and receiver pairs evenly paced.
- Great useful in building fast line following and grid navigating robots
- Comes with easy to use digital outputs that can be connected directly to microcontrollers
-
SmartElex IOIO OTG for Android
₹ 1,925.00(inc GST)
₹ 1631.36 (+18% GST extra)
- Recommended Input Voltage: 12V
- Input Voltage Range: 5-15V
- 2 Pin 2mm SMD JST Right-angle Connector for Input supply
- On-board TPS62133RGTT Synchronous step down DC-DC converter.
- Power Status LED (RED)
- Micro USB for Communication with Android.
- One start LED connected to boot pin (RC12 =Pin no. 39).
- User Switch SW1, SW2 connected to any port pin through SW1, SW2 Jumper respectively.
-
SmartElex Dual Channel Battle Relay
₹ 990.00(inc GST)
₹ 838.98 (+18% GST extra)
- Trigger Voltage: 5VDC
- Switching Voltage: [email protected]; [email protected]
- Relay resistance: 100 mΩ max
- Module operating voltage:Â 4.8V to 5.2V
- 40mA typical draw from the receiver
- Powerful auxiliary weapons control in RC combat.
- Glow plugs control in RC nitro vehicles.
-
SmartElex Battle Relay
₹ 590.00(inc GST)
₹ 500 (+18% GST extra)
- Switching Voltage: [email protected]; [email protected]
- Trigger Voltage: 5VDC
- Relay resistance: 100 mΩ max
- 4.8V to 5.2V operating voltage
- 30mA typical draw from receiver
- Powerful auxiliary weapons control in RC combat.
- Glow plugs control in RC nitro vehicles.
-
SmartElex ATmega32 Development Board on-board Programmer
₹ 749.00(inc GST)
₹ 634.75 (+18% GST extra)
- Onboard 5V regulator (78M05) circuit.
- On-Board power supply on-off switch
- Power Status LED (RED)
- User LED D0, D1 connected to any port pin through D0, D1 Jumper respectively.
- User Switch SW1, SW2 connected to any port pin through SW1, SW2 Jumper respectively.
- Onboard 12 MHz crystal
- Port extensions for all ports with detailed pin labeling for easy identification of pins
- Onboard USB TO Serial – CH340 Chip.
- On-board Micro USB USBASP for loading HEX file.
- Servo motor Connector (Run only up to 300mA).
-
SmartElex Aryabhatta 8051 Microcontroller Development Board AT89S52 with Onboard USB Programmer
₹ 489.00(inc GST)
₹ 414.41 (+18% GST extra)
- Quartz crystal 11.0592 MHz
- On board programmer.
- Reset button.
- Power plug-in jack.
- External pull-up resistors for Port 0.
- Port extensions for all ports.1.
- Good start for beginners.
- Easy to use.
-
SmartElex 10S DC Motor Driver HAT
₹ 749.00(inc GST)
₹ 634.75 (+18% GST extra)
- Wide 6V to 28V motor Operating Voltage.
- One brushed DC motor Bidirectional control.
- Current limiting at 35A.
- PWM frequency up to 32KHz
- Support TTL PWM from the microcontroller
- Internal thermal shutdown
- Under-voltage lockout
-
SmartElex 10D DC Motor Driver HAT for Raspberry Pi
₹ 1,189.00(inc GST)
₹ 1007.63 (+18% GST extra)
- Wide 6V to 28V motor Operating Voltage.
- Continuous 10A maximum current without Heatsink and 30A peak current for 10 Seconds.
- Two brushed DC motor Bidirectional control.
- Current limiting at 35A.
- PWM frequency up to 32KHz
- Support TTL PWM from the microcontroller
- Internal thermal shutdown
- Under-voltage lockout
- PWM and direction controlled driving of four externally powered NMOS transistors
- 3V and 5V logic level input.