Generic
Showing 1345–1392 of 6100 results
-
-
Other Metal Geared Motors
45RPM 12V Low Noise Dc Motor With Metal Gears – Grade A
SKU: 1137803- The metal gears have better wear and tear properties.
- The gearbox is sealed and lubricated with lithium grease and requires no maintenance.
- Although the motor gives 45 RPM at 12V, the motor runs smoothly from 4V to 12V and gives a wide range of RPM, and torque.
- The shaft has a hole for better coupling.
- Operating Voltage(V): 12
- Rated Torque(kg-cm): 4.2
- Stall Torque(kg-cm): 16
SKU: 1137803 -
-
6S Li-ion BMS
6S 40A 18650 Lithium Battery Protection Board
SKU: 618355- Maximum discharge current: 40A
- Instantaneous discharge current: 70A
- Charging voltage: 25.5V
- Maximum charging current: 40A
- Overcharge detection voltage: 4.25±0.025V
- Overcharge protection delay: 1.0±0.5S
- Overcharge release voltage: 4.15±0.05V
- Battery balance detection voltage: 4.125±0.025V
- Battery balance release voltage: 4.125±0.05V
- Battery balance current: 41±5mA
- Working current: ≤40uA
SKU: 618355 -
Slide Switches
Slide Switch SK-02
SKU: 1883638- MPN: SK-02
- Items: Standard
- Rated current: 50mA
- Rated voltage: 12V DC
- Insulation resistance: 100 MΩ min
- Insulation voltage: 100V DC
- Compressive strength: 110V AC for 50Hz/1 min
- Contact resistance: 50MΩ max
- Operating temperature range: -30°c to 85℃
- Lifetime: 10,000 Cycles min
- Operating force: 200 + 50gf or 200 – 50gf
- Travel: 1.5 + 0.1mm or 1.5 – 0.1mm
SKU: 1883638 -
-
Light/color Sensor
Photosensitive Resistor Sensor Module for Arduino
SKU: 766370- This is a High-quality photosensitive sensor module/light module detects the photosensitive resistor for Arduino
- Resistance of the photoresistor is typically less than 80 Ohms (in full light)
- Dark resistance is typically greater than 20 Meg Ohms (in full darkness)
SKU: 766370 -
-
3D Printer Extruder Parts and Fans
PC6-M10 Pneumatic Push in Bowden Extruder for 6mm tube J-Head fitting
3D Printer Extruder Parts and FansPC6-M10 Pneumatic Push in Bowden Extruder for 6mm tube J-Head fitting
SKU: 288374- Inside Diameter: 6mm
- Thread Size: M10
- PTFE Tubing Compatibility: 3mm ID PTFE Tubing (for 1.75mm Filament)
- Materials:Â Nickel Plated Brass
- Release Method:Â Elliptical John Guest Fitting
SKU: 288374 -
RC Car Wheel
65mm Robot Smart Car Wheel for BO Motors (Green)
SKU: 668614- Tire with sponge liner for more strength
- With upgraded tire tread for greater friction
- New design wheel for better combination with the motor
- Diameter: 65 mm
- Width : 28 mm
- The material of Wheel: High-strength plastic
- The material of Tyre: Rubber
- Color: Green
SKU: 668614 -
-
-
-
-
Other Sensors
PAJ7620 Gesture Recognition Sensor
SKU: 860807- The supply voltage is 2.8V- 3.3V and I/O voltage is 1.8V~3.3V
- Nine gesture recognition (Up / Down / Left / Right / Push / Pull / CW / CCW / Wave)
- Gesture speed is 60°/s to 600°/s in Normal Mode and 60°/s to 1200°/s in Gaming Mode
- Ambient light immunity: < 100k Lux
SKU: 860807 -
-
-
Current and Voltage Sensor
5A 12V Overcurrent Protection AC Current Detection Sensor Module
SKU: 400224LC 5A Over-current protection Sensor module uses a current transformer to collect the AC signal to achieve the relay over-current signal output within 0-5A. Relay pull while over-current, relay released while not over-current
SKU: 400224 -
-
12V Li-Ion Battery (11.1V~12.6V)
Orange INR 18650 11.1V 2000mAh 3C 3S1P Li-Ion Battery Pack
SKU: 514618- Maximum Output Voltage: 12.6 VDC.
- High energy density.
- Charge connector: JST-XH connector
- Discharge connector: Nylon Female T Connector
- Good consistency and low self-discharge.
- Long life with full capacity for up to 500 charge cycles.
- Inbuilt (BMS) battery protection circuit.
SKU: 514618 -
Raspberry Pi Case
Raspberry 4B Black Injection Molding Premium Case Supporting 3007 Fans
SKU: 1226956- Easy three-piece installation design.
- Easy fitment of Pi board.
- Case color: Black.
- Rubber pad grip at the bottom.
- Precise access to all port and cable strips.
- Injection Molded Construction.
SKU: 1226956
