Search results: “motor” – Page 20
Showing 913–960 of 1355 results
-
-
-
Emax Servo Motor
EMAX ES09A (Dual-bearing) Specific Swash Servo Motor for 450 Helicopters-(original)
SKU: 948733- Voltage: 4.8-6.0 V
- Torque: 2.2 / 2.4kgf.cm
- Rate: 0.11 / 0.09 s / 60 degrees
- STD Direction: Counter Clockwise/ Pulse travelling 1500 to 1900 μsec
- Gears: Plastic Gears
- Bearing Type: Dual-bearing
SKU: 948733 -
-
-
DC Geared Motors
RS-37 500 RPM High Torque Side Shaft DC Geared Motor
SKU: 436576RS-37 Gear motor is widely used for Industrial Applications. Carries torque greater as compared to Johnson Geared Motors and consumes less current as well. This motor has higher durability and is able to work for hours at a time
SKU: 436576 -
RS 50 Geared motor
RS-50 30 RPM High Torque Side Shaft DC Geared Motor
SKU: 459899RS-50 Gear motor is widely used for Industrial Applications. Carries torque greater as compared to Johnson Geared Motors and consumes less current as well. This motor has higher durability and is able to work for hours at a time
SKU: 459899 -
-
Shield for Arduino
HACK AF L293D Motor Driver/Servo Shield for Arduino Nano
SKU: 143257- Pin compatible with Adafruit Motor Shield
- Pin header to connect sensors and actuators.
- 4 H-Bridges L293D chipset.
- Surg Current Protection for IC L293D.
- Onboard On/Off Switch.
- Drive 4 bi-directional DC motors
- Drive 2 Servo motors (unipolar or bipolar)
- On-board slot to connect HC-05/HC-06 Bluetooth modules for Wireless control via Smartphone
SKU: 143257 -
Brushed / Brushless DC motor Driver
Cytron Smartdrive40 40Amp Dc Motor Driver (Peak 80Amp) Mds40A
SKU: 2780- Bi-directional control for a single brushed DC motor.
- Support motor from 7V to 25V.
- Maximum current up to 80A peak (1 second), 40A (5 minutes) or 30A (> 20 minutes) continuously.
- 16 KHz switching frequency for quiet operation.
- Reverse polarity protection.
- LiPo battery low voltage warning.
- Thermal protection.
- Current limiting base on temperature.
SKU: 2780 -
-
-
-
TowerPro and Other Servo Motors
TowerPro MG958 Digital High Torque Metal Gear Servo Motor
SKU: 618511- Operating Voltage: 4.8v-6.6v
- Stall Torque (4.8v): 18.0kg.cm
- Stall Torque (6.6v): 20.0kg.cm
- Servo arms & screws included and fit with Futaba servo arm
- CE & RoHS approved
- Servo case: Alloy case in the middle
- Gear Type: Metal gear
SKU: 618511 -
-
Other Metal Geared Motors
150RPM 12V Low Noise Dc Motor With Metal Gears – Grade A
SKU: 1137798- The metal gears have better wear and tear properties.
- The gearbox is sealed and lubricated with lithium grease and requires no maintenance.
- Although the motor gives 150 RPM at 12V, the motor runs smoothly from 4V to 12V and gives a wide range of RPM, and torque.
- The shaft has a hole for better coupling.
- Operating Voltage(V): 12
- Rated Torque(kg-cm): 2
- Stall Torque(kg-cm): 7.8
SKU: 1137798 -
-
-
Brushed / Brushless DC motor Driver
L293D Motor Driver Board for ESP8266 WiFi NodeMcu Lua ESP12E
SKU: 699566- Motor Power Range: 4.5V ~ 36V
- Control supply range: 4.5V ~ 9V
- Logical operating current Iss: ≤60mA
- Driving part of the work current Io: ≤1.2A
- Maximum power dissipation: 4W (T = 90 ℃)
- Operating temperature : -25 ℃ ~ + 125 ℃
- Drive Type: Dual high-power H-bridge driver
SKU: 699566 -
-
-
-
-
-
3D Printer Stepper Motors, Nema 23 Stepper Motors
57HM76-2804 NEMA 23 18Kg-cm Stepper Motor Round-Type
3D Printer Stepper Motors, Nema 23 Stepper Motors57HM76-2804 NEMA 23 18Kg-cm Stepper Motor Round-Type
SKU: 1551725- Model: 57HM76-2804
- Shaft Type: Round-Type
- Motor Body Length: 76mm
- Step Angle: 0.9°
- Current/Phase: 2.8A
- Resistance (Ω) /Phase: 1.15
- Inductance (mH/Phase): 5.6
- Holding Torque (kg-cm): 18
- No. of Leads: 4
SKU: 1551725 -
-
-
-
Nema 16 Stepper Motors
NEMA16 39HY38-0504 2.9Kg-cm Stepper Motor Round-Type Shaft
SKU: 1551704- Number of Phase: 2
- Step Angle: 1.8°
- Rated Voltage (V): 1.2
- Rated Current(A): 0.5A/phase
- Resistance (Ω): 24 Ω ± 10%/Phase
- Inductance (mH/Phase): 45 mH± 20%
- Shaft Diameter (mm): 5
- Holding Torque: 2.9 kg.cm
SKU: 1551704 -
Raspberry Pi Hats
Stepper Motor HAT V2.0 Shield for Raspberry Pi Zero/3B+/4B
SKU: 815872- Wide 5V to 12V Operating Voltage.
- Four Brushed DC Motor Bidirectional Control.
- Two Stepper Motor Control.
- Maximum Peak Current 3A
- PWM frequency up to 32KHz
- Support TTL PWM from the microcontroller
- Thermal Shutdown Protection
SKU: 815872 -
N20 Metal Gear Motors
N20-3V-300 RPM Micro Metal Gear-box DC Motor
SKU: 475324- This is a DC Mini Metal Gear Motor, ideal for making robots.
- Lightweight, high torque and low RPM.
- Fine craftsmanship, durable, not easy to wear.
- With excellent stall characteristics, can climb hills easily.
- You can also easily mount a wheel on the motor’s output shaft.
SKU: 475324 -
-
