IoT Development Boards
Showing 49–96 of 247 results
-
-
-
-
-
-
-
-
-
-
IoT Development Boards
TTGO SIM7600E-H Module ESP32- WROVER-E Chip WiFi Bluetooth 18560 Battery Holder Solar Charge Development Board Unsoldered
IoT Development BoardsTTGO SIM7600E-H Module ESP32- WROVER-E Chip WiFi Bluetooth 18560 Battery Holder Solar Charge Development Board Unsoldered
SKU: 1031136- Main chip:ESP32 WROVER-E
- Interface: USB, SD Card, Solar Input interface
- Car Clock:40MHz
- Button: Reset, Power switch
- Antenna: SIM Antenna,GPS Antenna
- Operating Temperature Range:-40-85 degrees
SKU: 1031136 -
-
IoT Development Boards
DFRobot FireBeetle 2 Board ESP32-S3 (N16R8) AIoT Microcontroller with Camera (Wi-Fi & Bluetooth on Board)
IoT Development BoardsDFRobot FireBeetle 2 Board ESP32-S3 (N16R8) AIoT Microcontroller with Camera (Wi-Fi & Bluetooth on Board)
SKU: 1601464- Operating Voltage: 3.3V
- Max Charging Current: 1A
- Operating Temperature: -20 to 70℃
- Processor: Xtensa® dual-core 32-bit LX7 microprocessor
- Main Frequency: 240 MHz
- SRAM: 512KB
- ROM: 384KB
- Flash: 16MB
SKU: 1601464 -
IoT Development Boards
M5STACK FIRE IoT Development Kit (PSRAM 2.0) V2.6
SKU: 945399- ESP32: 240MHz dual-core, 600 DMIPS, 520KB SRAM, Wi-Fi, dual-mode Bluetooth
- Flash Memory: 16MB
- PSRAM: 4MB
- Power Input: 5V @ 500mA
- IPS Screen: 2 inch, 320×240 Colorful TFT LCD, ILI9342C, max brightness 853nit
- MEMS: BMM150 + MPU6886
SKU: 945399 -
-
IoT Development Boards
DFRobot FireBeetle 2 ESP32 C6 IoT Development Board (Supports Wi-Fi 6, Bluetooth 5, Solar-Powered)
IoT Development BoardsDFRobot FireBeetle 2 ESP32 C6 IoT Development Board (Supports Wi-Fi 6, Bluetooth 5, Solar-Powered)
SKU: 1879629- Supporting Wi-Fi and Thread protocols.
- Supports Wi-Fi 6 protocol for lower latency and lower power consumption.
- Solar charging enables deployment without the need for power lines.
- Battery level detection allows monitoring of device battery information.
SKU: 1879629 -
-
-
-
IoT Development Boards
Sipeed Maixduino for RISC-V AI + IoT
SKU: 790007- Supply voltage of external power supply: 4.8V ~ 5.2V
- Supply current of external power supply :>600mA
- Temperature rise: <30K
- Frequency Range: 2400Mhz – 2483.5Mhz
- Onboard ESP32 module support 2.4G 802.11. b/g/n and Bluetooth 4.2
SKU: 790007 -
IoT Development Boards
NanoPi Neo-LTS
SKU: 1470330- CPU: Allwinner H3, Quad-core Cortex-A7 Up to 1.2GHz
- DDR3 RAM: 256MB/512MB
- Connectivity: 10/100M Ethernet
- USB Host: Type-A x 1, 2.54 mm pin x 2
- GPIO: 2.54mm pitch 36pin. It includes UART, SPI, I2C, IO etc
- Power: DC 5V/2A
- Working temperature: -20℃ to 70℃
SKU: 1470330 -
IoT Development Boards
Seeed Studio Grove – Vision AI Module V2 – Arm Cortex-M55 & Ethos-U55, TensorFlow and PyTorch supported, Arduino, Raspberry Pi, Seeed Studio XIAO, ESP-based dev board
IoT Development BoardsSeeed Studio Grove – Vision AI Module V2 – Arm Cortex-M55 & Ethos-U55, TensorFlow and PyTorch supported, Arduino, Raspberry Pi, Seeed Studio XIAO, ESP-based dev board
SKU: R100188- Microcontroller: Himax WiseEye2 HX6538 with dual-core Arm Cortex-M55 and integrated Arm Ethos-U55
- Input Voltage (V): 5V
- Power Supply Option: Dual 7-pin connector, Type-C & Grove Connector
- Onboard: PDM Microphone, SD Card Slot
- Baud Rate: 115200
SKU: R100188 -
-
IoT Development Boards
AC220V ESP8266 1 Channel WIFI Relay Module ESP-12S Wifi Development Board
SKU: 1165418Â 1.Model: LC-Relay-ESP12-1R-MVÂ 2.Work Voltage:AC90-250V/DC7-12V/USB5VÂ 3.WIFI IC: ESP8266Â 4.Communication Protocol:UARTÂ 5.Load voltatge:AC 250V or DC 30V(Max)Â 6.Load current:10A(Max)SKU: 1165418 -
IoT Development Boards
JTAGulator with JTAG Exploitation Learning kit
SKU: 1051958- 24 I/O channels with input protection circuitry
- Adjustable target voltage: 1.2 V to 3.3 V
- Supported target interfaces (as of firmware v1.1): JTAG/IEEE 1149.1, UART/asynchronous serial
- USB interface for direct connection to the host computer
SKU: 1051958 -
-