PIC
-
W5100 Ethernet Module Ethernet Network Module for arduino
SKU: 43276₹ 449.00(inc GST)
₹ 380.51 (+18% GST extra)
- Support Hardwired TCP/IP Protocols: TCP, UDP, ICMP, IPv4 ARP, IGMP, PPPoE, Ethernet
- 10BaseT/100BaseTX Ethernet PHY embedded
- Auto-Negotiation (Full-duplex and half duplex)
- Support Auto MDI/MDIX
- Simultaneously Supports to 4 independent sockets
- 0.18 µm CMOS technology
- 3.3V operation with 5V I/O signal tolerance
- Provide Serial Peripheral Interface (SPI MODE 0, 3) support
-
USB PIC Programmer – UP00B
SKU: 10109₹ 3,307.00(inc GST)
₹ 2802.54 (+18% GST extra)
- USB powered, no extra power needed to load program
- Two ZIF sockets (20 pins and 40 pins) to ease the program loading process
- Support most 8pin, 18pin, 28pin and 40pin PDIP 8 bit PIC MCU
- Support Windows XP, Vista, 7 (32 and 64-bits)
- Support Intel and AMD based system
- Support Laptop and desktop PC
-
USB ICSP PIC Programmer – UIC00B
SKU: 10053₹ 1,039.00(inc GST)
₹ 880.51 (+18% GST extra)
- Program most of the +3.3V or +5V PIC
- Compatible with PICkit2’s UART Tool and Logic Tool
- The program most of the current 8-, 16-, and 32-bit Flash PIC microcontroller
-
Compatible with Windows XP, Vista, 7, 8 and 8.1.
-
Compatible with Microchip’s PICkit 2.
-
Powered directly from the USB port.
-
NO EXTERNAL POWER REQUIRED for UIC00B to function.
-
Compatible with PICkit2’s Logic Tool and UART Tool.
-
PICkit3 PIC KIT3 Debugger Programmer Emulator Controller Development Board
SKU: 28352₹ 1,140.00(inc GST)
₹ 966.1 (+18% GST extra)
- Full-speed USB support using Windows standard drivers
- Real-time execution
- Processors run at maximum speeds
- Built-in over-voltage/short circuit monitor
- Low voltage to 5V (1.8 to the 5V range)
- Read/write program and data memory of the microcontroller
- Program up to 512K byte flash.
-
Olimex PIC32-PINGUINO-MICRO ARDUINO like PIC32MX440F256H USB OTG
SKU: 11189₹ 1,890.00(inc GST)
₹ 1601.69 (+18% GST extra)
- PIC32MX440F256H 80 Mhz microcontroller 256KB Flash 32KB RAM
- MicroSD card for data logging
- UEXT connector which allows many existing modules like RF, ZIGBEE, GSM, GPS to be connected
- Two LEDs
- One BUTTON
- RESET button
- A Mini USB connector is used, which is common and used in most cell phones, so you do not have to buy other cables
- All PIC ports available on 0.1″ connectors
-
MiNi ENC28J60 Ethernet LAN Network Module For Arduino SPI AVR PIC LPC
SKU: 43775₹ 299.00(inc GST)
₹ 253.39 (+18% GST extra)
- Fully Compatible with 10/100/1000Base-T Networks
- Integrated MAC and 10Base-T PHY
- Supports One 10Base-T Port with Automatic Polarity Detection and Correction
- Supports Full and Half-Duplex modes
- Programmable Automatic Retransmit on Collision
- Programmable Automatic Rejection of Erroneous Packets
- SPI Interface with Clock Speeds Up to 20 MHz
- For Arduino, SPI, AVR, PIC, LPC, STM32.
-
Cytron 40 pins PIC Start-Up Kit SK40C
SKU: 10095₹ 829.00(inc GST)
₹ 702.54 (+18% GST extra)
-
ICSP connector for UIC00B -simple and fast method to load program.
-
Perfect fit for 40 pins PIC16F and PIC18F.
-
Operating Voltage Range: 7V – 15VDC
-
2 x programmable switch.
-
2 x LED indicator.
-
Exchangeable Crystal.
-
Existing pad for 16 x 2 characters LCD display.
-
UART connection to interface with other controller or even computer.
-
-
CIKU PIC PIC18F4550 based Arduino form factor starter kit
SKU: 10107₹ 1,249.00(inc GST)
₹ 1058.47 (+18% GST extra)
-
Comes with pre-programmed PIC18F4550 with USB bootloader.
-
PIC18F4550 running at 48MHz (after PLL with 10MHz external crystal).
-
Power via USB or external DC adapter (7 – 12V).
-
On board 5V 800mA (Max 1A) voltage regulator.
-
On board 3.3V 500mA (Max 500mA) voltage regulator.
-
USB mini-B receptor for USB connection.
-
20 digital I/O pins.
-
6 analog input pin.
-
2 PWM output pin.
-
-
40 pins PIC Start-Up Kit Combo 2 SK40C + PIC18F4550 (SK40C2)
SKU: 10105₹ 1,459.00(inc GST)
₹ 1236.44 (+18% GST extra)
-
ICSP connector for UIC00B -simple and fast method to load program.
-
Perfect fit for 40 pins PIC16F and PIC18F.
-
2 x programmable switch.
-
2 x LED indicator.
-
Exchangeable Crystal.
-
Existing pad for 16 x 2 characters LCD display.
-
UART connection to interface with other controller or even computer.
-
USB on board for certain PIC18F.
-
-
40 pins PIC Start-Up Kit Combo 1 – SK40C PIC16F877A (SK40C1)
SKU: 10097₹ 1,249.00(inc GST)
-
ICSP connector for UIC00B -simple and fast method to load program.
-
Perfect fit for 40 pins PIC16F and PIC18F.
-
2 x programmable switch.
-
2 x LED indicator.
-
Exchangeable Crystal.
-
Existing pad for 16 x 2 characters LCD display.
-
-
40 Pins dsPIC Start-Up Kit – SKDS40A
SKU: 10086₹ 1,144.00(inc GST)
₹ 969.49 (+18% GST extra)
-
ICSP connector for UIC00A /B-simple and fast method to load program.
-
Perfectly fit for 40 pins dsPIC (16-bit), NOT for the 40-pins 8-bit PIC.
-
2 x programmable switch.
-
2 x programmable LED indicator.
-
Changeable Crystal – default 10MHz.
-
Existing pad for 16 x 2 characters LCD display.
-
-
28 Pins PIC Start-up Kit – SK28A
SKU: 10080₹ 724.00(inc GST)
₹ 613.56 (+18% GST extra)
-
Industrial grade PCB.
-
Every board is being tested before it is shipped out.
-
Compact platform and breadboard-friendly
-
Suitable for hobbyists and expert.
-
Save development and soldering time.
-
Turn pin for crystal comes with 20MHz Crystal by default, the user may use crystal at various frequencies
-
Mini USB socket on board may use PIC18F2550 for USB device development, example USB Bootloader.
-
2×8 Character Parallel LCD pad ready (optional).
-
-
18 Pins PIC Start-up Kit – SK18B
SKU: 10064₹ 619.00(inc GST)
₹ 524.58 (+18% GST extra)
-
Compact, powerful, flexible and robust start-up platform.
-
No extra components required for the PIC to function.
-
No more frustrated work plugging PIC out and back for re-programming.
-
Perfectly fit for 18 pins PIC16F MCU.
-
With UIC00A, the program can be loaded in less than 4 seconds.
-
On/Off switch for main power
-
DC adaptor socket as power input
-
-
16-bit or 32-bit PIC Start-Up Kit – SK1632
SKU: 10062₹ 628.00(inc GST)
₹ 532.2 (+18% GST extra)
-
Input voltage range: 7V to 15VDC.
-
1 x Programmable push button (digital input, connected to A1)
-
1 x Programmable LED (active high, connected to A0)
-
Replaceable Crystal (default 8MHz)
-
Ready pads for 2×8 Character parallel interface LCD
-
USB micro B socket for PIC that supports USB peripheral
-
USB bootloader may be utilized if needed
-
