motor driver
Showing all 15 results
-
-
Servo Motor Driver
16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
SKU: 43740- Adjustable frequency PWM up to about 1.6 KHz
- 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
- Configurable push-pull or an open-drain output
- The output enable pin to quickly disable all the outputs
- Terminal block for power input
- Reverse polarity protection on the terminal block input
- Green power-good LED
SKU: 43740 -
-
Stepper Motor Drivers
Green A4988 driver Stepper Motor Driver- Normal Quality
SKU: 1483566- Supply Voltage : 8-35 VDC.
- Current : 1.0A Â (no heatsink ).
- Current : 2.0A (with heat-sinking).
- logic input : 3 – 5.5V .
- Automatic current decay mode detection / choice.
- Mixed with slow current decay mode.
SKU: 1483566 -
Brushed / Brushless DC motor Driver
CYTRON SMART DRIVE MDDS30 DUAL 30A (80A Peak)
SKU: 29672- Battery low voltage indicator.
- Battery over voltage indicator.
- Thermal protection.
- Current limit protection.
- Bi-directional control for dual brushed DC motor.
- Support motor voltage from 7V to 35VDC.
- Dimension: 103 x 97 x 40 (LxWxH) mm.
SKU: 29672 -
Brushed / Brushless DC motor Driver
Enhanced Cytron 40Amp DC Motor Driver (Peak 80amp) MDS40B
SKU: 11648-
Bi-directional control for a single brushed DC motor.
-
Support motor from 10V to 45V.
-
Maximum current up to 80A peak, reduce to 40A gradually according to temperature.
-
16 KHz switching frequency for quiet operation.
-
NO Reverse polarity protection.
-
Protection of overvoltage.
SKU: 11648 -
-
Brushed / Brushless DC motor Driver
MD13S 13Amp DC Motor Driver – GROVE Compatible
SKU: 24027-
Support motor voltage ranges from 6V to 30V
-
Maximum current up to 13A continuous and 30A peak (10 seconds).
-
GROVE compatible
-
3.3V and 5V logic level input.
-
SMD compatible
- Peak Current (A): 30 (10 seconds)
- Continuous Current (A): 1
- No. of Channels: 1
SKU: 24027 -
-
Stepper Motor Drivers
TB6600 0.2-5A CNC Controller Stepper Motor Driver Single Axes Two Phase Hybrid Stepper Motor for CNC
Stepper Motor DriversTB6600 0.2-5A CNC Controller Stepper Motor Driver Single Axes Two Phase Hybrid Stepper Motor for CNC
SKU: 835839- Input Current: 1~5A
- Supply Voltage: 12 to 48VDC
- Output Current: 0.2~5.0A
- Power (MAX): 160W
- Temperature: -10～45℃
- H bridge bipolar constant current drive.
SKU: 835839 -
Stepper Motor Drivers
TB6600 Stepper Motor Driver Controller 4A 9~42V TTL 16 Micro-Step CNC 1 Axis
SKU: 43211- Input Current: 0~5A
- Output Current: 0.5~4.0A
- Control Signal: 3.3~24V
- Power (MAX): 160W
- Micro Step: 1, 2/A, 2/B, 4, 8, 16, 32
- Temperature: -10～45℃
- H bridge bipolar constant current drive.
SKU: 43211 -
Stepper Motor Drivers
TMC2209 Stepper Motor DriverF
SKU: 835841- Maximum current: 2A per phase (continuous, with cooling), 2.8A peak per phase
- Works with 3.3V and 5V signals
- Comes with heatsink for better cooling
- Has StealthChop technology for quieter stepper motors
- Has SpreadCycl technology for smoother movements
SKU: 835841 -
Stepper Motor Drivers
DRV8825 Stepper Motor Driver with Aluminum Heat Sink
SKU: 6721- Supply Voltage: 8.2 – 42 VDC.
- Current Capacity : 2.2A max(24V).
- Continuous current per phase: 1.5 A.
- Minimum Logic voltage: 2.5V.
- Maximum Logic Voltage: 5V.
- Microstep resolutions:Â full, 1/2, 1/4, 1/8, 1/16, and 1/32.
- Dimensions : 15 x 20 mm.
- Weight: 4 gm.
SKU: 6721 -
-
Brushed / Brushless DC motor Driver
Sabertooth Dual 12A Motor Driver
SKU: 4692- 12A continuous, 25A peak per channel Up to 24V in
- Synchronous regenerative drive
- Ultra-sonic switching frequency
- Thermal and overcurrent protection
- Lithium protection mode
- Peak Current (A): 25A
- Continuous Current (A): 12
- Operating Voltage(VDC): 18 to 24V
- No. of Channels: 2
SKU: 4692 -
Brushed / Brushless DC motor Driver
Cytron MDD10A Dual Channel Enhanced 10Amp DC Motor Driver 30A Peak
Brushed / Brushless DC motor DriverCytron MDD10A Dual Channel Enhanced 10Amp DC Motor Driver 30A Peak
SKU: 3405- Bi-directional control of 2 brushed DC motor.
- Support motor voltage ranges from 5V to 25V.
- Maximum current up to 10A continuous and 30A peak (10 seconds) for each channel.
- Solid state components provide faster response time and eliminate the wear and tear of the mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
SKU: 3405
