Generic
Showing 1345–1392 of 6094 results
-
-
-
Light/color Sensor
Photosensitive Resistor Sensor Module for Arduino
SKU: 766370- This is a High-quality photosensitive sensor module/light module detects the photosensitive resistor for Arduino
- Resistance of the photoresistor is typically less than 80 Ohms (in full light)
- Dark resistance is typically greater than 20 Meg Ohms (in full darkness)
SKU: 766370 -
6S Li-ion BMS
6S 40A 18650 Lithium Battery Protection Board
SKU: 618355- Maximum discharge current: 40A
- Instantaneous discharge current: 70A
- Charging voltage: 25.5V
- Maximum charging current: 40A
- Overcharge detection voltage: 4.25±0.025V
- Overcharge protection delay: 1.0±0.5S
- Overcharge release voltage: 4.15±0.05V
- Battery balance detection voltage: 4.125±0.025V
- Battery balance release voltage: 4.125±0.05V
- Battery balance current: 41±5mA
- Working current: ≤40uA
SKU: 618355 -
-
Current and Voltage Sensor
5A 12V Overcurrent Protection AC Current Detection Sensor Module
SKU: 400224LC 5A Over-current protection Sensor module uses a current transformer to collect the AC signal to achieve the relay over-current signal output within 0-5A. Relay pull while over-current, relay released while not over-current
SKU: 400224 -
Other Sensors
PAJ7620 Gesture Recognition Sensor
SKU: 860807- The supply voltage is 2.8V- 3.3V and I/O voltage is 1.8V~3.3V
- Nine gesture recognition (Up / Down / Left / Right / Push / Pull / CW / CCW / Wave)
- Gesture speed is 60°/s to 600°/s in Normal Mode and 60°/s to 1200°/s in Gaming Mode
- Ambient light immunity: < 100k Lux
SKU: 860807 -
12V Li-Ion Battery (11.1V~12.6V)
Orange INR 18650 11.1V 2000mAh 3C 3S1P Li-Ion Battery Pack
SKU: 514618- Maximum Output Voltage: 12.6 VDC.
- High energy density.
- Charge connector: JST-XH connector
- Discharge connector: Nylon Female T Connector
- Good consistency and low self-discharge.
- Long life with full capacity for up to 500 charge cycles.
- Inbuilt (BMS) battery protection circuit.
SKU: 514618 -
Raspberry Pi Case
Raspberry 4B Black Injection Molding Premium Case Supporting 3007 Fans
SKU: 1226956- Easy three-piece installation design.
- Easy fitment of Pi board.
- Case color: Black.
- Rubber pad grip at the bottom.
- Precise access to all port and cable strips.
- Injection Molded Construction.
SKU: 1226956 -
-
-
-
-
Environmental Sensors
Wind Speed Sensor Voltage Type(0-5V) Anemometer Kit (Waterproof & Industrial)
SKU: 28669- High hardness, Corrosion protection.
- Waterproofness and High precision.
- The mode of its output signal:0-5V(Voltage signal).
- supply voltage: DC 12-24V.
- Power consumption:Voltage MAX≤0.3W.
- Start wind speed:0.4-0.8m/s.
SKU: 28669 -
-
Electronic Switches/Keypads Modules
TTP226 8-way Capacitive Touch Switch Module
SKU: 617807- Onboard 8 key TTP226 capacitive touch induction IC.
- Onboard 8-way level indicator.
- Working voltage: 2.4 to 5.5 V.
- Modules, you can set the output mode, key output mode, the longest time and fast/low power output
SKU: 617807 -
IoT Cameras, Raspberry Pi Camera
OV5647 5MP 1080P IR-Cut Camera for Raspberry Pi 3/4 with Manual Day Night Mode
IoT Cameras, Raspberry Pi CameraOV5647 5MP 1080P IR-Cut Camera for Raspberry Pi 3/4 with Manual Day Night Mode
SKU: 537522- Raspberry Pi Camera, supports all revisions of the Pi
- Using IR-CUT filter, it can eliminate colour distortion in the daylight
- 5-megapixel OV5647 sensor
- Can Attach IR LEDs if Night Vision mode is required
SKU: 537522 -
Signal Generator Module & Oscilloscopes
ICL8038 12V to 15V, Signal Generator, Medium/Low Signal, Frequency 10Hz-450KHz, Triangular/Rectangular/S, ine Wave Generator, Module
Signal Generator Module & OscilloscopesICL8038 12V to 15V, Signal Generator, Medium/Low Signal, Frequency 10Hz-450KHz, Triangular/Rectangular/S, ine Wave Generator, Module
SKU: 1121315- Working voltage: 12V ~ 15V
- Output: Triangular wave, Square wave and sine wave.
- Frequency range: 10HZ ~ 450kHz
- Low distortion sine wave: 1%
- Duty cycle range: 2% to 98%
- Low temperature drift: 50ppm / ℃
- Triangular wave output linearity: 0.1%
- Working temperature: 0 ~ 70 ℃
- Board size: 54.5*37.8mm
SKU: 1121315 -
Case for Arduino
Transparent Blue ABS Plastic Case for UNO R3
SKU: 766385- Made of high-quality ABS plastic, provide good protective
- For Arduino UNO R3 Development Board only.
- To protect your little computer against damages, dust and scratches Clear Top and Bottom.
- This case provides easy access to all ports.
- It requires no tools for easy assembly and disassembly.
SKU: 766385 -
-
-
RC Car Wheel
65mm Robot Smart Car Wheel for BO Motors (Green)
SKU: 668614- Tire with sponge liner for more strength
- With upgraded tire tread for greater friction
- New design wheel for better combination with the motor
- Diameter: 65 mm
- Width : 28 mm
- The material of Wheel: High-strength plastic
- The material of Tyre: Rubber
- Color: Green
SKU: 668614