Search results: “motor” – Page 5
Showing 193–240 of 1355 results
-
Straight Type DC BO Motors
100 RPM Dual Shaft BO Motor-Straight
SKU: 104043- Low density: lightweight, low inertia.
- Capability to absorb shock and vibration as a result of elastic compliance.
- Ability to operate with minimum or no lubrication, due to inherent lubricity.
- The relatively low coefficient of friction.
- Operating Voltage(VDC): 3~12
- Shaft Length (mm): 8.5
- Shaft Diameter (mm): 5.5 (Double D-type)
- No Load Current: 40-180mA.
- Rated Speed(After Reduction): 100 RPM
- Rated Torque: 0.35 Kgcm
SKU: 104043 -
TowerPro and Other Servo Motors
TowerPro MG996R Digital High Torque Servo Motor (360° Rotation)
SKU: 618530- Weight: 55g
- Dimension: 40.7×19.7×42.9mm
- Stall torque: 9.4kg/cm (4.8v); 11kg/cm (6.0v)
- Operating speed: 0.19sec/60degree (4.8v); 0.15sec/60degree (6.0v)
- Operating voltage: 4.8 ~ 6.6V
- Gear Type: Metal gear
- Dead band width: 1us
- Wire length: 32cm
SKU: 618530 -
N20 Metal Gear Motors
N20-3V-100 RPM Micro Metal Gear-box DC Motor
SKU: 475122- This is a DC Mini Metal Gear Motor, ideal for making robots.
- Lightweight, high torque and low RPM.
- Fine craftsmanship, durable, not easy to wear.
- With excellent stall characteristics, can climb hills easily.
- You can also easily mount a wheel on the motor’s output shaft.
SKU: 475122 -
TowerPro and Other Servo Motors
MG90S 9g Servo Metal Gear
SKU: 1119224- Dimensions: 23 x 12.2 x 29mm
- Operating Speed (4.8V no load): 0.11sec / 60 degrees
- Operating Speed (6.0V no load): 0.10sec / 60 degrees
- Stall Torque (4.8V): 2.0 kg/cm
- Stall Torque (6.0V): 2.5 kg/cm
- Temperature Range: 0 to 55 degree C
- Rotation angle: 360 °
- Dead Band Width: 15 Microsecond
- Operation Voltage: 4.8 – 6.0 Volts
- Recommend Model: Mini Car / Mini Ship /Helicopter & Airplane
SKU: 1119224 -
-
Best Prices, Servo Motor Drivers
16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
-26%Best Prices, Servo Motor Drivers16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
SKU: 43740- Adjustable frequency PWM up to about 1.6 KHz
- 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
- Configurable push-pull or an open-drain output
- The output enable pin to quickly disable all the outputs
- Terminal block for power input
- Reverse polarity protection on the terminal block input
- Green power-good LED
SKU: 43740 -
Cytron Motor Drivers
Cytron 10 A Switch Control Potentiometer DC Motor Driver (MD10POT)
SKU: 234226The MD10-POT control circuit is designed to enable the speed to be controlled via a potentiometer (10K Ohm) which is included in the package. It does not work with analog voltage from an external controller The 3-way rocker switch is used for start/stop and direction control.
SKU: 234226 -
Cytron Motor Drivers
Cytron 3Amp 4V-16V Dual Channel DC Motor Driver MDD3A
SKU: 381249- Bidirectional control for two brushed DC motor.
- Control one unipolar/bipolar stepper motor.
- Operating Voltage: DC 4V to 16V
- Maximum Motor Current: 3A continuous, 5A peak
- Buck-boost regulator to produce 5V output (200mA max).
- Buttons for quick testing.
SKU: 381249 -
Cytron Motor Drivers
Cytron 30Amp DC Motor Driver (Peak 80Amp) MD30C R2
SKU: 2774- Bi-directional control of 1 brushed DC motor.
- Motor Voltage: 5V – 30V.
- Maximum Current: 80A peak (1 second), 30A continuously.
- Reverse polarity protection.
- 3.3V and 5V logic level input.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
SKU: 2774 -
-
-
Cytron Motor Drivers
Cytron 20Amp 6V-30V DC Motor Driver MD20A
SKU: 381393- Bidirectional control for one brushed DC motor.
- Operating Voltage: DC 6V to 30V
- Maximum Motor Current: 20A continuous, 60A peak
- Buttons for quick testing.
- LEDs for motor output state.
- Overcurrent protection with active current limiting.
- Temperature protection.
- Undervoltage shutdown.
SKU: 381393 -
Cytron Motor Drivers
Cytron 10Amp 7V-30V DC Motor Driver for R/C (2 Channel) MDDRC10
SKU: 945382- Operating Voltage: DC 7 V to 30 V
- Maximum Motor Current: 10 A continuous, 30 A peak
- Motor Output PWM Frequency: 20 kHz
- RC Input Voltage (RC1 & RC2): Low Level: 0-0.7 V | High Level: 1.5-15 V
- Output Maximum Current: 0-500 mA
SKU: 945382 -
Cytron Motor Drivers
Cytron 25A 7V-58V DC motor driver with Switch and Potentiometer Control (MD25HV POT)
Cytron Motor DriversCytron 25A 7V-58V DC motor driver with Switch and Potentiometer Control (MD25HV POT)
SKU: 497900- Bidirectional control for one brushed DC motor.
- Maximum Motor Current: 25A continuous, 60A peak.
- 5V output for the host controller (250mA max).
- Buttons for quick testing.
- PWM frequency up to 40kHz.
- Dual Input Mode: PWM/DIR or Potentiometer/Switch Input.
SKU: 497900 -
Motor and Display Driver ICs
L293D PowerDIP-16 Stepper Motor Controller/ Driver
SKU: 162093- Overtemperature Protection
- Logical “0” Input Voltage Up To 1.5 V (High Noise Immunity)
- Internal Clamp Diodes.
- Featuring Unit rode L293 and L293D
- Wide Supply-Voltage Range: 4.5 V to 36 V
- Separate Input-Logic Supply
- Internal ESD Protection
- Thermal Shutdown
- High-Noise-Immunity Inputs
SKU: 162093 -
-
Cytron Motor Drivers
Cytron Enhanced 13Amp DC Motor Driver 30A peak (10 seconds) MD10C
SKU: 2777- Bi-directional control for 1 brushed DC motor, single channel
- Support motor voltage ranges from 5V to 30V.
- Maximum current up to 13A continuous and 30A peak (10 seconds).
- 3.3V and 5V logic level input.
- Solid state components provide faster response time and eliminate the wear and tear of the mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
SKU: 2777 -
-
Servo motor Accessories
GT POWER 3-Channel Multi Servo Tester
SKU: 57812- Operating Voltage: DC 4.8-6V
- Offer 3 modes to check servos or ESC
- The Manual Mode allows you to turn the knob to different speeds and check the reaction time
- The Neutral mode makes the servo go back to the neutral point
- The Automatic ’’Window Wiper’’ Mode makes the servo swing like a window wiper in the largest angle possible
- Connect to up to 3 servos simultaneously
- Full aluminum alloy housing
SKU: 57812 -
3D Printer Stepper Motors, Stepper Motors
28BYJ-48 Stepper Motor and ULN2003 Stepper Motor Driver – Good Quality
3D Printer Stepper Motors, Stepper Motors28BYJ-48 Stepper Motor and ULN2003 Stepper Motor Driver – Good Quality
SKU: 17304- Rated voltage: 5V DC
- Reduction Ratio: 64:1
- Step Angle: 5.625° /64
- Frequency: 100Hz
- Self-positioning Torque: >34.3mN.m
- Friction torque: 600-1200 gf.cm
- Pull in torque: 300 gf.cm
SKU: 17304 -
Best Prices, Stepper Motor Drivers
A4988 driver Stepper Motor Driver- Normal Quality
SKU: 52807- Supply Voltage : 8-35 VDC.
- Current : 1.0A (no heatsink ).
- Current : 2.0A (with heat-sinking).
- logic input : 3 – 5.5V .
- Automatic current decay mode detection / choice.
- Mixed with slow current decay mode.
SKU: 52807 -
Other Servo Accessories
Cellmeter 8 Multi-Functional Digital Power Servo Tester
SKU: 57763- Balance Discharge Current: 90mA × 8 Cell(Max@Cell Voltage 4.2v)
- Servo Test Frequency: 50Hz, 60Hz, 100Hz, 125Hz, 200Hz, 250Hz, 300Hz,
- Battery Voltage Test Precision: 0.001V
- Support Battery Type: Can test Li-Po, Li-ion, Li-Fe (2-8S), NiCd, NiMH(4-8S) battery
- High visibility LCD display screen
- Port for balance plug for up to 8 cell Lipo, LiFe, or Li-Ion batteries
- Can be used as Servo tester to test standard and narrow servos.
- Port for discharge plug of NiMh/NiCd batteries
SKU: 57763 -
-
Stepper Motor Drivers
DRV8825 Stepper Motor Driver with Aluminum Heat Sink
SKU: 6721- Supply Voltage: 8.2 – 42 VDC.
- Current Capacity : 2.2A max(24V).
- Continuous current per phase: 1.5 A.
- Minimum Logic voltage: 2.5V.
- Maximum Logic Voltage: 5V.
- Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32.
- Dimensions : 15 x 20 mm.
- Weight: 4 gm.
SKU: 6721 -
Drone Motor
Set of 4 A2212 1400KV Brushless Motor for Drone with SimonK 30A ESC and Orange 1045 Propeller Set
Drone MotorSet of 4 A2212 1400KV Brushless Motor for Drone with SimonK 30A ESC and Orange 1045 Propeller Set
SKU: 5931- Offers great performance and value for money.
- Comes in the compact sizes.
- Suitable for airplane, aircraft, quadcopter.
- ESC used has an On-Board BEC.
- Faster and Better speed control.
SKU: 5931 -
Drone Motor
A2212 1000 KV Brushless DC Motor with SimonK 30A ESC and Orange 1045 Propeller Set
SKU: 5923- Offers great performance and value for money.
- Suitable for airplane, aircraft, quadcopter.
- Motor KV: 1000
- LiPO Batteries: 2S-3S
- Shaft Diameter: 3.17 mm
- ESC used has an On-Board BEC.
- Propeller: Orange HD 1045
SKU: 5923 -
Drone Motor
Set of 4 A2212 1000 KV BLDC Brushless DC Motor with SimonK 30A ESC and Orange 1045 Propeller Set
Drone MotorSet of 4 A2212 1000 KV BLDC Brushless DC Motor with SimonK 30A ESC and Orange 1045 Propeller Set
SKU: 5924- Offers great performance and value for money.
- Suitable for airplane, aircraft, quadcopter.
- Motor KV: 1000
- LiPO Batteries: 2S-3S
- Shaft Diameter: 3.17 mm
- ESC used has an On-Board BEC.
- Propeller: Orange HD 1045
SKU: 5924 -