Flight Controllers

  • F3 Brushed Flight Control Board Based On SP RACING F3 EVO Brush for Micro FPV Frame

    Product Code(SKU): 45650
     1,090.00 (inc GST)


    1. Supported Receiver Input Signal: PPM, SBUS, DSM
    2. Support PPM, SBUS, DSM receiver input signal
    3. Battery voltage detection and buzzer interface
    4. Run on SP RACING F3 EVO firmware 32 brush flight control
    5. Large current NMOS transistors, operating current can reach 10A or higher
    6. Use STM32F303CCT6 + MPU6500, advanced hardware platform F3 for higher flight stability
    Add to cart
  • OMNIBUS F4 V2 PRO Flight Controller with SD Card Slot & BEC

    Product Code(SKU): 57107
     2,690.00 (inc GST)
    1. Dimensions: 37 x 37 x 10 mm(L x H x W)
    2. Weight: 12 gm.
    3. SPI Gyro MPU6000
    4. MicroSD Blackbox
    5. F4 Processor (F405)
    6. 5v3a SBEC
    7. Built-in Current Sensor
    8. On-Board OSD (controlled by Beta flight, FC over SPI bus)
    9. On-Board Video Filter (only can supply 5V to VTX and Camera)
    10. On-Board Voltage Regulator and Power supply (BEC)
    Add to cart
  • Pixhawk PX4 Autopilot PIX 2.4.8 32 Bit Flight Controller

    Product Code(SKU): 29453
     5,950.00 (inc GST)
    1. The advanced 32-bit ARM CortexM4 high-performance processors can run NuttX RTOS real-time operating system.
    2. 14 PWM / servo output.
    3. Bus interface (UART, I2C, SPI, CAN).
    4. The integrated backup power and backup controller fails, the primary controller fails over to the backup control is safe.
    5. Provide automatic and manual modes.
    6. Provide redundant power input and failover.
    7. Multicolor LED lights.
    8. Provide multi-tone buzzer Interface.
    9. Micro SD recording flight data.
    Add to cart
  • Naze 32 Full REV6 Flight Controller with Compass & Barometer

    Product Code(SKU): 57248
     1,749.00 (inc GST)


    1. 2000 degrees/second 3-axis MEMS gyro + accelerometer (MPU6500).
    2. Input voltage: Max 16V on input rail and up to 35V 6s on the voltage sense line.
    3. Fully pinout compatible with rev5 accessories (OSDoge etc).
    4. SBUS Inverter.
    5. Sonar pads w/resistors added for direct connection to 5V sonar.
    6. MS5611 barometer.
    7. 128mbit flash.
    Read more
  • DJI NAZA-M Lite V1.1 with GPS Kit

    Product Code(SKU): 56686
     6,900.00 (inc GST)
    1. Supported Multi-Rotor: Quad-rotor I4, X4 / Hex-rotor I6, X6, IY6, Y6.
    2. Supported ESC Output: 400Hz refresh frequency.
    3. Recommended Transmitter: PCM or 2.4GHz with minimum 4 channels.
    4. Power Consumption: MAX1. 5W (0.3A@5V) Normal:0.6W (0.12A@5V).
    5. Weight: MC:25g; VU:20g; GPS:21.3g.
    6. All-in-One Design.
    7. Advanced attitude stabilized Algorithm.
    8. Multiple flight control mode/intelligent switching.
    9. GPS Module Available/Accurate Position hold.
    10. Intelligent Orientation Control (IOC).
    11. Failsafe mode.
    Add to cart
  • SP Racing F3 Flight Controller Deluxe

    Product Code(SKU): 45528
     2,590.00 (inc GST)
    1.  Stackable design – perfect for integrating with OSDs and power distribution boards.
    2. 16 PWM I/O lines for ESCs, Servos and legacy receivers. 8 available on standard pin headers. 8 via side mounted connectors.
    3. Full support for OneShot ESCs for easy PID tuning and a sharper response.
    4. Supports SBus, SumH, SumD, Spektrum1024/2048, XBus, PPM, PWM receivers.
    5. No external inverters required (built-in).
    6. Dedicated output for programmable LEDs – great for orientation, racing and night flying.
    7. Dedicated I2C port for connection of OLED display without needing flight battery.
    8. Battery monitoring ports for voltage and current.
    9. Sonar support for precision low-altitude hold.
    10. Buzzer port for audible warnings and notifications.
    11. Symmetrical design for a super tidy wiring.
    12. Barometer mounted on the bottom of the board for easy wind isolation.
    13.  Wire up using pin headers, JST-SH sockets or solder pads. Use either right-angled or straight pin-headers.
    Add to cart
  • OpenPilot CC3D EVO Flight Controller Straight Pin

    Product Code(SKU): 50818
     1,249.00 (inc GST)
    1. 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer.
    2. Tiny 36 x 36 mm 4 layer PCB for superior electrical noise reduction and flight performance.
    3. Software support for Windows, Mac, and Linux.
    4. Direct high-speed USB support with no drivers required, a true plug and play device.
    5. Spektrum satellite receiver support.
    6. Futaba S-BUS hardware support.
    7. Innovative Flexi-port technology for superior port flexibility.
    8. 4Mbits onboard EEPROM for configuration storage.
    Add to cart
  • Flip32 OMNIBUS F4 Flight Controller

    Product Code(SKU): 127316
     1,499.00 (inc GST)
    1. 128Mb Flash(16M Byte)
    2. SBUS/PPM input (Pinheaders)
    3. DSM/DSM2/DSMX input(Plug)
    4. 6PWM output (Pinheaders)
    5. Only 36x36mm, mount holes 30.5×30.5mm
    6. All through hole pin header Design  -no Sh connectors
    7. STM32 F405 MCU, Runs Raceflight CC3D REVO firmware
    8. Works Perfect with Raceflight or BetaFlight 3.0
    Add to cart
  • F4 Flight Controller

    Product Code(SKU): 57329
     1,790.00 (inc GST)
    1. Dshot support
    2. Drag and Drop OSD configured via Beta flight Configurator
    3. MPU6000 6 axis SPI Gyro & Accelerometer
    4. SBUS/PPM AND Spektrum DSMX Ports
    5. MicroSD card black box
    6. Onboard Video Filter(only can supply 5V to VTX and Camera)
    7. SmartAudio V2 via tx6 on J10
    Add to cart
  • Matek F405-OSD Flight Controller

    Product Code(SKU): 57074
     3,190.00 (inc GST)
    1. 168MHz STM32F405RGT6
    2. 6-axis ICM-20602 (3-axis gyroscope. 3-axis accelerometer)
    3.  BetaFlight OSD
    4.  MicroSD BlackBox
    5.  VCP and 5 x UARTs
    6.  6 PWM/DSHOT outputs
    7.  MatekF405 Target
    Add to cart
  • APM 2.8 Flight Controller with Built-in Compass

    Product Code(SKU): 28963
     2,490.00  2,490.00 (inc GST)
    1. Straight Needle
    2. Arduino Compatible!
    3. Onboard 4 MegaByte Dataflash chip for automatic data logging.
    4. Optional off-board GPS, a uBlox LEA-6H module with Compass.
    5. One of the first open source autopilot systems to use Invensense’s 6 DoF Accelerometer/Gyro MPU-6000.
    Add to cart
  • DJI Naza-M Lite Multi-Rotor Flight Controller

    Product Code(SKU): 29615
     4,950.00 (inc GST)
    1. All-in-One Design
    2. Low Voltage Protection
    3. 6 Supported Multi-rotor Types
    4. Advanced Attitude Stabilize Algorithm
    5. Intelligent Orientation Control (IOC)
    6. Motor Arm and Motor Dis-arm
    7. Built-in Gimbal Stabilization Function, Failsafe Mode
    8. Support Futaba S-Bus and PPM Receiver
    9. Supported ESC output: 400Hz refresh frequency
    Add to cart
  • OpenPilot CC3D EVO Flight Controller with Side Pins

    Product Code(SKU): 29588
     1,090.00  1,090.00 (inc GST)
    1. Powerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and 20KB RAM.
    2. 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer.
    3. Tiny 36 x 36 mm 4 layer PCB for superior electrical noise reduction and flight performance.
    4. Software support for Windows, Mac, and Linux.
    5. Direct high-speed USB support with no drivers required, a true plug and play device.
    6. Spektrum satellite receiver support.
    7. Futaba S-BUS hardware support.
    Add to cart
  • Omnibus F4 V2 PRO Flight Controller with Built-in OSD

    Product Code(SKU): 61182
     1,990.00 (inc GST)
    1. STM32 F405 MCU
    2. Runs Beta flight (3.0.1 and up)
    3. Race light and D-ronin firmware
    4. SBUS/PPM input (Pinheaders)
    5. 6PWM output (1-4Pinheaders and Sh1.0 Plug, 5-6 as Pinheaders)
    6. Only 36x36mm, mount holes 30.5×30.5mm
    7. SPI Sensor MPU6000
    8. 128Mbit Flash
    Add to cart
  • SP Racing F3 Flight Controller Integrate OSD ACRO Version

    Product Code(SKU): 61253
     2,590.00 (inc GST)
    1. STM32F303 CPU, 72Mhz inc FPU
    2. CPU: STM32F303, 72Mhz inc FPU
    3. Acro: High-Capacity Flash
    4. Accelerometer/gyro: MPU6050
    5. Board size: 36 x 36 x 5mm (without shell)
    6. Board weight: 5.9g
    7. Weight: 22 gm(with all accessories)
    Add to cart
  • Pixhawk PX4 2.4.7 32Bits Flight Controller for Quadcopter Multicopter

    Product Code(SKU): 28968
     8,099.00 (inc GST)
    1. 168 MHz / 252 MIPS Cortex-M4F
    2. 14 PWM / Servo outputs (8 with failsafe and manual override, 6 auxiliaries, high-power compatible)
    3. Abundant connectivity options for additional peripherals (UART, I2C, CAN)
    4. Integrated backup system for in-flight recovery.
    5. Manual override with dedicated processor and stand-alone power supply (fixed-wing use)
    6. Backup system integrates mixing, providing consistent autopilot and manual override mixing modes (fixed wing use)
    7. Redundant power supply inputs and automatic failover
    8. External safety switch
    9. Multicolor LED main visual indicator
    10. High-power, multi-tone piezo audio indicator
    11. MicroSD card for high-rate logging over extended periods of time
    Add to cart
  • Naze32 10DOF Flight Control Board

    Product Code(SKU): 29597
     1,615.00 (inc GST)
    1. Axis: 2000 degrees/second 3-axis MEMS gyro.
    2. Input voltage: Max 16V on input rail and up to 35V 6s on the voltage sense line.
    3. Built-in FrSky telemetry inverter (shared w/main port).
    4. Battery voltage monitoring.
    5. A modern 32-bit processor running at 3.3V/72MHz (STM32F103CB).
    6. Onboard MicroUSB for setup and configuration.
    7. LEDs so bright, they could blind you.
    8. MultiWii-based configuration software for easy setup.
    9. Rev5 hardware.
    Add to cart
  • OMNIBUS F4 Pro V3 Flight Controller

    Product Code(SKU): 127282
     2,990.00 (inc GST)
    1. STM32 F403 MCU (Spi connected to Gyro)
    2. Built-in Current/Voltage sensor!
    3. Firmware hex = OMNIBUSF4SD hex from the drop-down.
    4. MPU6000 (the 6 axis SPI Gyrometer + Accelerometer)
    5. Smart audio capable VTX PID Programming
    6. D- Shot Supported (no Modification)
    7. OSD (configured over Betaflight UI)
    8. SD CARD Slot for BlackBox
    9. SBUS/PPM + DSMX Ports
    10. SmartAudio V2 via J10
    11. current + voltage + rssi + buzzer as pins
    Add to cart
  • KK2.1.5 Multi-rotor LCD Flight Control Board With 6050MPU And Atmel 644PA (original)

    Product Code(SKU): 3106
     1,990.00 (inc GST)
    1. MODEL: KK2.1.5 (ORIGINAL)
    2. IC: Atmega644 PA
    3. GYRO/ACC.: 6050MPU InvenSense Inc.
    4. AUTO LEVEL: Yes
    5. INPUT VOLTAGE: 4.8V-6.0V
    6. AVR INTERFACE: Standard 6 Pin
    7. SIGNAL FROM RECEIVER: 1520us(5 channels)
    8. SIGNAL TO ESC: 1520us
    Add to cart
  • SP Racing F3 Flight Controller Integrate OSD Deluxe Version

    Product Code(SKU): 45522
     3,850.00 (inc GST)
    1. 36x36mm board with 30.5mm mounting holes
    2. STM32F303 CPU, 72Mhz inc FPU
    3. High-Capacity Flash
    4. MPU6050 accelerometer/gyro
    5. MS5611 barometer (Deluxe only)
    6. HMC5883 compass (Deluxe only)
    Add to cart
  • Mini APM3.1 Flight Controller with Power Module for Multicopter FPV

    Product Code(SKU): 45511
     3,290.00 (inc GST)
    1. 8 Channel PWM input
    2.  8 motor outputs
    3.  12-way Auxiliary input and output
    4.  Supports GPS, compass, telemetry and power module
    5.  Onboard connections JST-SH with 1.0mm pitch
    6.  Compatible with official Firmware and Groundstation.
    Add to cart
  • SP Racing F3 Flight Controller ACRO Version

    Product Code(SKU): 45626
     1,190.00 (inc GST)
    1. The STM32F3 CPU, MPU 6500 sensor, 16M high-capacity flash memory, OSD function.
    2. The SP F3 runs Cleanflight which can be configured to suit your needs using a cross-platform GUI (Windows/OSX/Linux).
    3. Tiny and lightweight, the Racing F3 has a standard 36x36mm form-factor with 30.5mm mounting holes and weighs just 6 grams.
    4. Flight Logging, on-board high-capacity black box flight log recorder – optimize your tuning and see the results of your setup without guesswork.
    5. OneShot ESC, full support for OneShot ESCs for easy PID tuning and a sharper response.
    6. Broad RC receiver supports SBus, SumH, SumD, Spektrum1024/2048, XBus, PPM, PWM receivers, no external inverters required (built-in).
    Add to cart
  • DJI NAZA-M V2 Multirotor Autopilot Controller set with GPS

    Product Code(SKU): 45468
     14,890.00 (inc GST)
    1. All-In-One Compact Multi-Rotor Autopilot System
    2. New Assistant Software for Smartphones
    3. Multiple Flight Control Modes and Intelligent Switching
    4. GPS Module Available for Accurate Position Stabilization
    5. 2-Axis Gimbal Stabilization
    6. Two Levels of Low Voltage Warnings and Protection
    7. Single Motor Failure Protection
    8. Supports Remote Gain Adjustment from the Transmitter
    9. Enhanced Failsafe Features, Including Auto Return-to-Home
    10. Supported ESC Output 400 Hz refresh frequency
    11. Supported Transmitters PCM or 2.4 GHz radio with at least 4 channels
    12. Power Consumption MAX: 1.5 W (0.3 A at 5 V)
    13. Operating Temperature: -10 to 50°C
    14. Supports 9 Different of Multi-Rotor Configurations, Ideal for DJI F450/F550 and E Series Tuned Propulsion Systems
    Read more
  • Naze32 6DOF Flight Control board

    Product Code(SKU): 29592
     1,090.00 (inc GST)
    1. Battery voltage monitoring.
    2. Built-in FrSky telemetry converter.
    3. Modern 32-bit processor (STM32 F103) running at 3.3V/72MHz.
    4. Onboard USB for setup and configuration.
    5. Modern GUI for all operating systems, Baseflight Configurator.


    Add to cart

Price shown are inclusive of GST. >>Read More<<