Generic
Showing 49–96 of 6095 results
-
Breakout Board
MP3-TF-16P MP3 SD Card Module with Serial Port
SKU: 31193- Supports sampling rates (KHz): 8 / 11.025 / 12/16 / 22.05 / 24/32 / 44.1 / 48
- 24-bit DAC output, dynamic range support: 90dB, SNR support: 85dB
- Fully supports FAT16, FAT32 file system
- Maximum support 32G TF card
- Support U disk to 32G, 64M bytes of NORFLASH
- A variety of control modes are available. IO control mode, serial mode, AD key control mode
SKU: 31193 -
-
Buck Converter
DC to DC 6-24V to 5V USB Output Step Down Power Charger Buck Converter
SKU: 405611- Maximum Output Current: 3A MAX
- Conversion efficiency: can up to 97.5%
- Switch frequency: 500KHz
- Output Ripple: 10mV around (12V to 5V3A) 20M bandwidth
- Output indicator: Output voltage indicator is red
- Operating temperature: Industrial grade (-40 ° to + 85 °)
- Output overvoltage protection: Yes, input 1.5A fuse, output 5V have 300W TVS tube clamp protection.
- Flat copper inductor, improve conversion efficiency
- High-quality USB port
SKU: 405611 -
-
Temperature & Humidity Sensor
DHT11 Digital Relative Humidity and Temperature Sensor Module
SKU: 28586- The module can detect the surrounding environment of the humidity and temperature
- High reliability and excellent long-term stability
- The output from the digital output
- Working voltage 3.3V-5V
- Humidity measurement range: 20%-95% (0-50 degrees range)
- Humidity measurement accuracy: ±5.0%RH
- Temperature measurement range: 0 degrees -50 degrees
- Temperature measurement accuracy: ±2.0degree.
SKU: 28586 -
USB Interface Module
3.3V Adapter Board for 24L01 Wireless Module
SKU: 395873- It can be used with NRF24L01 wireless module
- Add core nRF24L01+ Breakout Adapter with onboard 3.3V Regulator
- Onboard 3.3V voltage regulator accepts your Arduino +5V supply and provides 3.3V for the attached nRF24L01+ module
- Allows for easy connection to nRF24L01+ modules
- Small power on SMD LED indicator
SKU: 395873 -
IR and RF Transmitters and Receivers
4 Channel Wireless Four Button RF Remote Control Transceiver Module (Mode: Non Locking)
IR and RF Transmitters and Receivers4 Channel Wireless Four Button RF Remote Control Transceiver Module (Mode: Non Locking)
SKU: 28460- No. of the channel: 4
- Operating mode: Non-Locking
- Receiver Operating voltage: DC 5V.
- Receiver sensitivity is: -98dB.
- Transmitter Operating voltage: DC 12V
- Transmitting frequency: 315 MHZ.
- Transmitter Operating current: 10mA at 12V.
- TransmitterRadiated power: 10mW at 12V.
- Transmission distance (m): 3 to 5.
SKU: 28460 -
-
-
-
Breadboard and Zero PCBs
400 Tie Points Contacts Mini Circuit Experiment Solderless Breadboard
SKU: 498432- 400 tie points
- 2 Power lanes, Total 100 tie points in power lanes
- 1 Double strip, Total 300 tie points
- Perfect for Arduino shield prototyping and testing
- Plastic housing, metal contact clips
SKU: 498432 -
-
Cables for Arduino
Cable for Arduino UNO/MEGA (USB A to B)-1M
SKU: 618211- Fully compatible with the PC.
- Moulded strain relief and PVC over moulding to ensure a lifetime of error-free data transmissions.
- Aluminium under mould shield helps meet FCC requirements on KMI/RFI interference.
- Foil and braid shield complies with fully rated cable specifications reducing EMI/FRI interference.
SKU: 618211 -
-
-
-
Load / Pressure / Force / Flex Sensor
BF350 High Precision Resistance Strain Gauge / Pressure Sensor / Weighing Sensor 350 Ohm
Load / Pressure / Force / Flex SensorBF350 High Precision Resistance Strain Gauge / Pressure Sensor / Weighing Sensor 350 Ohm
SKU: 975711- Technical Indexes: BF series
- Strain limit: 2.0%
- Fatigue life: ≥1M
- Resistance: 350 ohms
- Contrast: 800: 1 (Min) (transmission)
- Sensitivity coefficient: 2.00-2.20
SKU: 975711 -
-
Buck Converter
AMS1117-3.3 LDO 800MA DC 5V to 3.3V Step-Down Power Supply Module
SKU: 31179- Input Voltage: 4.5V to 15V
- Output Voltage: 3.3V to 5V
- Output Current: 800mA
- Onboard AMS1117 chip.
- Onboard power indicator to indicate power is turned on: Red LED.
- Output voltage interface, connection to facilitate the experimental.
- Small Compact Size, 3Pin Type, Breadboard Friendly.
SKU: 31179 -
Water TDS, pH, Flow, Level and Pressure Sensor
Anti-Corrosion Water Level Sensor with Ball Float Switch
Water TDS, pH, Flow, Level and Pressure SensorAnti-Corrosion Water Level Sensor with Ball Float Switch
SKU: 28661- Rating contract (Max.): 10 W
- Switching power supply (Max.): 110VDC
- Resistance contract (Max.): 100 Ω
- Appro. Float Ball Size (mm) : 24×17 (LxD)
- Body Total Length (mm) : 85
- Cable Length (cm) : 37
- Total Float opening: 70°
- Switch ON/OFF angle Approx. betn 15° to 20°
SKU: 28661 -
-
Shield for Arduino
L293D Motor Driver/Servo Shield for Arduino
SKU: 9736- 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
- 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes.
- Can run motors on 4.5VDC to 25VDC.
- Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, or interleaved stepping.
SKU: 9736 -
-
-
Thermoelectric Peltier Elements
Thermoelectric Peltier Refrigeration Cooling System Kit
SKU: 502117- Using GL style of the refrigerator, effectively release the thermal deformation ability of the refrigerator produce at work.
- Small volume, does not occupy space, installation is simple.
- It can be used as a Pet Air Conditioner (chicken, little dog, etc.) or a little fridge.
- Lightweight, small size and easier to install.
SKU: 502117 -
Stepper Motor Drivers
DRV8825 Stepper Motor Driver with Aluminum Heat Sink
SKU: 6721- Supply Voltage: 8.2 – 42 VDC.
- Current Capacity : 2.2A max(24V).
- Continuous current per phase: 1.5 A.
- Minimum Logic voltage: 2.5V.
- Maximum Logic Voltage: 5V.
- Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32.
- Dimensions : 15 x 20 mm.
- Weight: 4 gm.
SKU: 6721 -
Relay Modules
6-30V 1-Channel Power Relay Module with Adjustable Timing Cycle
SKU: 400057- Operating voltage: 6-30V
- Time interval:0.1 s (minimum) ~ 999 min (maximum) continuously adjustable.
- Trigger Signal Source: High-Level Trigger (3.0 V-24 V)
- Output Capacity: can control no more than DC 30V 5A AC or 220 V devices 5A
- Optocoupler Isolation.
SKU: 400057 -
Official Raspberry Pi Accessories
Micro USB-B (Female) to USB Type C (Male) Converter Adapter for Raspberry Pi 4
Official Raspberry Pi AccessoriesMicro USB-B (Female) to USB Type C (Male) Converter Adapter for Raspberry Pi 4
SKU: 471150- Can be used for All development Board with C type port for 5V@3A supply
- Supports Reversible plug orientation
- Simple Plug and Play device, no driver software required.
- Supports High-speed data transfers
- Can be Use for Mobile and Tablets with Fast Charging support
- Compact and Light Weight
SKU: 471150 -
-
Other ESP WIFI Modules
ESP8266 Adapter Plate Serial Wireless WIFI Module-1pcs
SKU: 31233- It features reserved land-pattern for the 3.3V regulator
- It has Pinouts on the top layer in black colour.
- Compatible with Latest ESP-12F ESP8266 Wifi Module
- It includes a 10K pull-up resistor populated on PCB.
SKU: 31233 -
-
-
-
Buck Converter
LM2596 HV DC-DC Buck Converter 4.5-40V to 3-35V Adjustable Step Down Module
SKU: 520422- Input voltage: 4.5-40V,
- Output voltage: (3-35V) continuously adjustable (recommended load debugging).
- Minimum pressure: 1.5V
- Output current: rated current 2A, 3A maximum
- Output Power: 15W maximum
SKU: 520422
