Flight Controller & Accessories
Showing 97–144 of 166 results
-
-
Flight Controller & Accessories
SpeedyBee BLS 35A Mini V2 20×20 4-in-1 ESC
SKU: R100762- Firmware: BLHeli S J-H-40
- Continuous Current: 35A * 4
- Burst Current: 45A(5seconds)
- ESC Protocol: DSHOT300/600
- Power Input: 3-65 LiPo
- Power Output: VBAT(Battery voltage, used to power the flight controller)
SKU: R100762 -
Flight Controller & Accessories
SpeedyBee F405 Mini BLS 35A 20×20 Stack
SKU: R100760- MCU STM32F405
- IMU(Gyro) ICM42688P
- USB Port type Type-C
- Barometer Built-in OSD Chip AT7456E chip
- Power Input 3-6S LiPo.
- The flight controller is powered through the G, V wires of the 8pin harness or G, V pads from the bottom side of the flight controller.
SKU: R100760 -
-
Flight Controller & Accessories
T Motor MINI F45A 6S 4IN1
SKU: 1800267- Mini body strong performance.
- Reliable & High-Quality MOSFET.
- Safeguard electronic components from vibration impact.
- Input Voltage: 3- 65
- ESC Firmware: BLHeli32
- Telemetry: Support
- galvanometer: Support
- Mounting pitch: 20 x 20mm
- Weight: 9.2g
- beta flight galvanometer ratio: 200
SKU: 1800267 -
Flight Controller & Accessories
Whoop Lite F3 Mini Brushed Flight Controller
SKU: 974877- CPU: STM32F030
- Six-Axis: MPU6050
- Firmware version: Silverware firmware
- Power Cable: 55mm, with JST-PH 2.0 connector
- ESC: All FETs are rated at 6A maximum. Support 6x15mm/7x20mm/8x20mm/8.5x20mm etc motors.
- Size: 26mm x 26mm, fully compatible with the Inductrix quad frame and mounting pattern
SKU: 974877 -
Flight Controller & Accessories
 Pixhawk 6C (plastic case)
SKU: R100011- Advanced flight controller with PX4 Autopilot.
- STM32H743 processor up to 480 MHz for efficient processing.
- Redundant IMUs for reliability from Bosch & InvenSense.
- An integrated vibration isolation system ensures accurate readings.
- Suitable for academic, commercial, and research applications.
- Cost-effective design with high performance.
SKU: R100011 -
Flight Controller & Accessories
AeroFC Flight Controller Board
SKU: 821127- High-Speed STM32 processor
- Triple Redundant IMU
- Light Weight
- Isolated & Dampened IMU
- Compatible with Ardupilot and PX4.
- It can be configured with AeroGCS, Mission Planner, QGround Control software, etc.
Limited Time Launch Offer !!!
SKU: 821127 -
-
Flight Controller & Accessories, Interfacing Cables
DF13 4 Pin Flight Controller Cable
SKU: 58221- Item Name: DF13 4 Pin Flight Controller Cable
- 100% Brand new and high quality.
- Weight: about 3g
- Plug Type: DF 13 4 pin
- Length: 200mm(28AWG).
- Color: Red, and Black
- Useful for connection between the PixHawk and the GPS receiver module. or many receiver connections.
SKU: 58221 -
-
Flight Controller & Accessories, Interfacing Cables
DF13 6 Pin Flight Controller Cable
SKU: 58194- Item Name: DF13 6 Pin Flight Controller Cable
- 100% Brand new and high quality.
- Weight: about 3g
- Plug Type: DF 13 6 pin
- Length: 200mm(26AWG).
- Color: Red, and Black
- Useful for connection between the PixHawk and the GPS receiver module. or many receiver connections.
SKU: 58194 -
Flight Controller & Accessories
DJI Naza M Lite Multi-Rotor Flight Controller without GPS
SKU: 29615- Input Voltage (V): MC: 4.8V~5.5V (recommended 2S~6S Lipoly).
- Power Consumption: MAX: 1.5W (0.3A @ 5V), Normal: 0.6W (0.12A @ 5V).
- Operating Temperature:-10°C ~ +50°C.
- Supported ESC Output: 400Hz refresh frequency
SKU: 29615 -
Flight Controller & Accessories
DJI NAZA M V2 Multirotor Autopilot Controller set with GPS
SKU: 45468- Input Voltage (V): MC: 4.8V~5.5V (recommended 2S~6S Lipoly).
- Supported ESC Output 400 Hz refresh frequency
- Supported Transmitters PCM or 2.4 GHz radio with at least 4 channels
- Power Consumption MAX: 1.5 W (0.3 A at 5 V)
- Operating Temperature: -10 to 50°C
SKU: 45468 -
Flight Controller & Accessories
DJI NAZA-M Lite V1.1 with GPS Kit
SKU: 56686- Supported Multi-Rotor: Quad-rotor I4, X4 / Hex-rotor I6, X6, IY6, Y6.
- Supported ESC Output: 400Hz refresh frequency.
- Recommended Transmitter: PCM or 2.4GHz with minimum 4 channels.
- Power Consumption: MAX1. 5W (0.3A@5V) Normal:0.6W (0.12A@5V).
- Weight: MC:25g; VU:20g; GPS:21.3g.
- All-in-One Design.
- Advanced attitude stabilized Algorithm.
- Multiple flight control mode/intelligent switching.
- GPS Module Available/Accurate Position hold.
- Intelligent Orientation Control (IOC).
- Failsafe mode.
SKU: 56686 -
Flight Controller & Accessories
EMAX Mini Magnum 2 F4 35A Flytower 20x20mm 35A 2-6S BLHeli_32 4in1 ESC+F4 Flight Controller OSD+VTX
Flight Controller & AccessoriesEMAX Mini Magnum 2 F4 35A Flytower 20x20mm 35A 2-6S BLHeli_32 4in1 ESC+F4 Flight Controller OSD+VTX
SKU: 812603- Stack Size: 20x20mm
- Flight Controller: F4 Flight Controller (OMNIBUSF4 Firmware)
- ESC: 4in1 BLHeli_32 35A ESC
- Supply Voltage: 2-6S lipo
- VTX: 25mW/200mW
SKU: 812603 -
Flight Controller & Accessories
F3 Brushed Flight Control Board Based On SP RACING F3 EVO Brush for Micro FPV Frame
Flight Controller & AccessoriesF3 Brushed Flight Control Board Based On SP RACING F3 EVO Brush for Micro FPV Frame
SKU: 45650- Supported Receiver Input Signal: PPM, SBUS, DSM
- Support PPM, SBUS, DSM receiver input signal
- Battery voltage detection and buzzer interface
- Run on SP RACING F3 EVO firmware 32 brush flight control
- Large current NMOS transistors, operating current can reach 10A or higher
- Use STM32F303CCT6 + MPU6500, advanced hardware platform F3 for higher flight stability
SKU: 45650 -
Flight Controller & Accessories
F3 EVO V2.0 Flight Control
SKU: 674161- Supported Receiver Input Signal: PPM, SBUS, DSM
- Support PPM, SBUS, DSM receiver input signal
- Battery voltage detection and buzzer interface
- Large current NMOS transistors, operating current can reach 10A or higher
- Use STM32F303CCT6 + MPU6500, advanced hardware platform F3 for higher flight stability
SKU: 674161 -
Flight Controller & Accessories
Flip32 OMNIBUS F4 Flight Controller
SKU: 127316- 128Mb Flash(16M Byte)
- SBUS/PPM input (Pinheaders)
- DSM/DSM2/DSMX input(Plug)
- 6PWM output (Pinheaders)
- Only 36x36mm, mount holes 30.5×30.5mm
- All through hole pin header Design  -no Sh connectors
- STM32 F405 MCU, Runs Raceflight CC3D REVO firmware
- Works Perfect with Raceflight or BetaFlight 3.0
SKU: 127316 -
Flight Controller & Accessories
Holybro Original Pixhawk PX4 Flight Controller (without GPS)
SKU: 311064- Main FMU Processor: STM32F76
- 32 bit ARM® Cortex® M7, 216 MHz Processor running NuttX RTOS,
- More computing power and 2X the RAM than previous versions)
- Abundant connectivity options for additional peripherals (UART, I2C, CAN)
- Redundant power supply inputs and automatic failover
- External safety button for easy motor activation
- New sensors with higher temperature stability
- Multicolor LED indicator
- Integrated vibrations isolation
- High-power, multi-tone piezo audio indicator
- microSD card for long-time high-rate logging
SKU: 311064 -
-
-
-
Flight Controller & Accessories
Micro Minim OSD For Racing F3 Naze32 Flight Controller RC Drone
SKU: 29457- ATmega328P with Arduino bootloader.
- MAX7456 monochrome on-screen display.
- +5V 500mA regulator for up to +12V supply input.
- FTDI cable compatible pinout.
- The standard 6-pin ISP header.
- Standalone, or with APM/ Flip / Flip32+ flight controllers.
SKU: 29457 -
Flight Controller & Accessories
Mini APM3.1 Flight Controller with Power Module for Multicopter FPV
SKU: 45511- 8 Channel PWM input
- Â 8 motor outputs
- Â 12-way Auxiliary input and output
- Â Supports GPS, compass, telemetry and power module
- Â Onboard connections JST-SH with 1.0mm pitch
- Â Compatible with official Firmware and Groundstation.
SKU: 45511 -
Flight Controller & Accessories
Mini OSD for Pixhawk Flight Controller
SKU: 57684- ATmega328P with Arduino bootloader
- MAX7456 monochrome on-screen display
- FTDI cable compatible pinout
- Standard 6 pin ISP header
- 2 independent power sections with an LED indicator on each
- Solder jumpers for combining the power sections
Compatible flight controller:
APM2.5/2.6/2.8
Pixhawk PX4SKU: 57684 -
-
Flight Controller & Accessories
Mini USB (90° Connector) to FPV AV Output Cable for GoPro Hero 3
SKU: 29366- USB connector is used to connect to the USB port on your GoPro Hero3 Camera.
- The 3 pin female connector is for AV video output
Typical application:
Video output from your GoPro Hero 3 USB port to your video wireless transmitter. (Connect your GoPro Hero 3 directly to FPV transmitter)
SKU: 29366