Categories
  • You cannot add "Play Station(PS) Female Connector For Play Station 2" to the cart because the product is out of stock.
L293D Motor DriverServo Shield for Arduino
L293D Motor DriverServo Shield for Arduino L293D Motor Driver/Servo Shield for Arduino L293D Motor Driver/Servo Shield for Arduino L293D Motor Driver/Servo Shield for Arduino L293D Motor DriverServo Shield for Arduino

L293D Motor Driver/Servo Shield for Arduino

9 Review(s)
Availability: In stock
SKU: 9736

QUICK OVERVIEW

  1. 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
  2. 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes.
  3. Can run motors on 4.5VDC to 25VDC.
  4. Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
  5. Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
  6. Pull down resistors keep motors disabled during power-up
  7. Big terminal block connectors to easily hook up wires (18-26AWG) and power
  8. 2-pin terminal block and jumper to connect external power, for separate logic/motor supplies

 179.00

(inc GST)

₹ 151.69 (+18% GST extra)

In stock

Purchase this product now and earn 2 Robu Points!

This L293D Motor Driver/Servo Shield for Arduino is probably one of the most versatile on the market and features 2 servo and 4 motor connectors for DC or stepper motors. That makes it a great shield for any robotic project.

This Arduino compatible motor Driver shield is a full-featured product that it can be used to drive 4 DC motor or two 4-wire steppers and two 5v servos. It drives the DC motor and stepper with the L293D, and it drives the servo with Arduino pin9 and pin10.

L293D is a monolithic integrated, high voltage, high current, 4-channel driver. Basically, this means using this chip you can use DC motors and power supplies of up to 36 Volts, that some pretty big motors and the chip can supply a maximum current of 600mA per channel, the L293D chip is also what’s known as a type of H-Bridge. The H-Bridge is typically an electrical circuit that enables a voltage to be applied across a load in either direction to an output, e.g. a motor.

The shield contains two L293D motor drivers and one 74HC595 shift register. The shift register expands 3 pins of the Arduino to 8 pins to control the direction of the motor drivers. The output enables the L293D is directly connected to PWM outputs of the Arduino.

Firmware
  1. Arduino Stepper/Servo software library with microstepping support.
    To install, click on Download in the top right corner, select zip and uncompress the folder.
    Rename the folder to AF-motor (check that the renamed folder contains the .cpp and .h files) and install into the Arduino sketches/libraries folder. For information how to use and install libraries, see our tutorial! This version now works with the Mega. Public domain!
  2. AccelStepper library with AFMotor support. This library allows for advanced stepper control including acceleration and deceleration, and concurrent stepper control!
    To install, click on Download in the top right corner, select zip and uncompress the folder.
    Rename the folder to AF-motor (check that the renamed folder contains the .cpp and .h files) and install into the Arduino sketches/libraries folder.
Note:

Power for the motors can be supplied from the Arduino boards DC Jack (normally 9V) or from the 2-pin EXT-PWR terminal block. If you are supplying power from the EXT_PWR terminal block you should remove the PWR jumper or you could damage the shield and the Arduino board.

<<We have a variety of modules that can be interfaced with this L293D Motor Driver/Servo Shield. Some of them are listed below click on their name to know more>>

Arduino Boards
Servo Motors
DC Motors
28BYJ-48 Stepper Motor


Features :

  1. 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
  2. 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 25VDC.
  3. Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
  4. Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
  5. Pull-down resistors keep motors disabled during power-up
  6. Big terminal block connectors to easily hook up wires (18-26AWG) and power
  7. Arduino reset button brought up top
  8. 2-pin terminal block and jumper to connect external power, for separate logic/motor supplies
  9. Tested compatible with Arduino Mega 1280 & 2560, Diecimila, Duemilanove, and UNO
  10. Download the easy-to-use Arduino software library, check out the examples and you’re ready to go!

Package Includes :

1 x L293D Motor Driver/Servo Shield for Arduino


Tutorial :

Continuous Output Current

1.2A

Logic control voltage Vss

4.5~5.5V

Dimensions in mm (LxWxH)

70x54x18

Weight (gm)

25

Shipment Weight

0.125 kg

Shipment Dimensions

8 x 6 x 3 cm

15 Days Warranty

This item is covered with a standard warranty of 15 days from the time of delivery against manufacturing defects only. This warranty is given for the benefit of Robu customers from any kind of manufacturing defects.  Reimbursement or replacement will be done against manufacturing defects.


What voids warranty:

If the product is subject to misuse, tampering, static discharge, accident, water or fire damage, use of chemicals & soldered or altered in any way.

9 reviews for L293D Motor Driver/Servo Shield for Arduino

  1. Rated 5 out of 5

    Sholi (verified owner)

    Execellent quality

  2. Rated 5 out of 5

    Pratik (verified owner)

    Nice product and good quality

  3. Rated 5 out of 5

    saurabh sinha (verified owner)

    very good product – Very fast delivery

  4. Rated 5 out of 5

    mayurkumarchauhan19@gmail.com (verified owner)

    nice , fast transportation .

  5. Rated 5 out of 5

    mayurkumarchauhan19@gmail.com (verified owner)

    very good product

  6. Rated 5 out of 5

    Akshay KG (verified owner)

    Good product, working perfectly in my project

  7. Rated 5 out of 5

    NanduMaji (verified owner)

    Very good Quality product, working great……. Fast shipping…

  8. Rated 4 out of 5

    Vishnu Haran (verified owner)

    the product is good but the motor connection part is somewhat rusted.
    But works fine.

  9. Rated 5 out of 5

    Pratham Maske

    good product

Add a review

Your email address will not be published. Required fields are marked *

Datasheet

Schematic

Pin Diagram

Questions and answers of the customers

There are no questions yet. Be the first to ask a question about this product.

Only registered users are eligible to enter questions