Cytron
Cytron, an electronics company, based in Malaysia, was founded in 2004 by five Universiti Teknologi Malaysia (UTM) students. Their primary goal is to help others by sharing their robotics expertise and getting those hard-to-find parts for projects for Students and Educators. Robu.in has been Cytron’s exclusive partner in India since 2014 and we are proud to be sharing a common goal in empowering the DIY & Robotics community with innovative and useful products at economical prices. Cytron is famous throughout the world for its Motor Drivers as well as IoT based products!
-
Cytron Arduino PS2 Shield
SKU: 2506₹ 1,349.00(inc GST)
₹ 1143.22 (+18% GST extra)
- 5V powered low current consumption.
- Simple to use UART protocol
- Vibrator motor on PS2 is controllable.
- Wired and Wireless PS2 controller is supported.
- PS2 Controller will automatically operate in analog mode.
- A status LED
- Jumper selector to select different UART Baud Rate (9600, 57600, 115200).
- Jumper selectors to select different digital pin as UART TX and RX pin.
-
Cytron 30Amp DC Motor Driver (Peak 80Amp) MD30C R2
SKU: 2774₹ 3,045.00(inc GST)
₹ 2580.51 (+18% GST extra)
- Bi-directional control of 1 brushed DC motor.
- Motor Voltage: 5V – 25V.
- Maximum Current: 80A peak (1 second), 30A continuously.
- Reverse polarity protection.
- 3.3V and 5V logic level input.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
-
Cytron Enhanced 13Amp DC Motor Driver 30A peak (10 seconds) MD10C
SKU: 2777₹ 935.00(inc GST)
₹ 792.37 (+18% GST extra)
- Bi-directional control for 1 brushed DC motor, single channel
- Support motor voltage ranges from 5V to 30V.
- Maximum current up to 13A continuous and 30A peak (10 seconds).
- 3.3V and 5V logic level input.
- Solid state components provide faster response time and eliminate the wear and tear of the mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
-
Cytron SmartDrive40 40AMP DC MOTOR DRIVER (PEAK 80AMP) MDS40A
SKU: 2780₹ 5,239.00(inc GST)
- Bi-directional control for a single brushed DC motor.
- Support motor from 7V to 25V.
- Maximum current up to 80A peak (1 second), 40A (5 minutes) or 30A (> 20 minutes) continuously.
- 16 KHz switching frequency for quiet operation.
- Reverse polarity protection.
- LiPo battery low voltage warning.
- Thermal protection.
- Current limiting base on temperature.
-
Cytron MDS160A SmartDrive160 160AMP Dc Motor Driver (Peak 190Amp)
SKU: 2784₹ 19,845.00(inc GST)
₹ 16817.8 (+18% GST extra)
- Bi-directional control for a single brushed DC motor.
- Support input voltage from 8V to 28V.
- Maximum current up to 190A peak (1 minute), 175A (2 minutes) or 160A (continuously).
- 16 KHz switching frequency for quiet operation.
- LiPo battery low voltage warning.
- Thermal protection.
-
Cytron MDD10A Dual Channel Enhanced 10Amp DC Motor Driver 30A Peak
SKU: 3405₹ 1,890.00(inc GST)
₹ 1601.69 (+18% GST extra)
- Bi-directional control of 2 brushed DC motor.
- Support motor voltage ranges from 5V to 25V.
- Maximum current up to 10A continuous and 30A peak (10 seconds) for each channel.
- Solid state components provide faster response time and eliminate the wear and tear of the mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
-
10A Motor Driver Shield – MD10
SKU: 3408₹ 1,564.00(inc GST)
₹ 1325.42 (+18% GST extra)
- Bi-directional control of 1 brushed DC motor.
- Support motor voltage ranges from 7V to 25V, .
- Maximum current up to 10A continuous and 15A peak (10 seconds).
- Solid state components provide faster response time and eliminate the wear and tear of a mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
- Speed control PWM frequency up to 10KHz.
- Selectable digital pins for PWM and DIR.
-
Planetary DC Geared Motor 63 RPM 196N-CM 12V IG42E-104K
SKU: 7960₹ 6,289.00₹ 5,660.00(inc GST)
₹ 4796.61 (+18% GST extra)
You save: ₹ 629.00
- Brand: Cytron
- Voltage: 12VDC
- Rated Torque: 19.99 kg.cm (1.96 N.m)
- Rated Speed: 63 RPM
- Rated Current: 5500mA
- Rated Power output: 41.3W
- Gear ratio: 104:1
- Encoder Output: 120 PPR
-
Planetary DC Geared Motor 430 RPM 11N-cm 12V IG32E-14K
SKU: 7974₹ 3,999.00₹ 2,999.00(inc GST)
₹ 2541.53 (+18% GST extra)
You save: ₹ 1,000.00
- Brand: Cytron
- Voltage: 12VDC
- Rated Torque: ~1.122 kg.cm (110 mN.m)
- Rated Speed: 430 RPM
- Rated Power: 7 W
- Gear ratio: 14:1
- Encoder Output: 98 PPR
- Gear Material: Metal
-
Planetary DC Geared Motor 405 RPM 64N-CM 12V IG42E-14K
SKU: 3430₹ 6,889.00₹ 5,489.00(inc GST)
₹ 4651.69 (+18% GST extra)
You save: ₹ 1,400.00
- Brand: Cytron
- Rated Voltage: 12VDC
- Rated Torque: 6.526kg.cm (640mN.m)
- Rated Speed: 405 RPM
- Rated Current: 5500mA
- Rated Power output: 41.3W
- Gear ratio: 14:1
- Encoder Output: 70 PPR
-
Planetary DC Geared Motor 250 RPM 100N-CM 12V IG42E-24K
SKU: 7965₹ 6,999.00₹ 5,299.00(inc GST)
₹ 4490.68 (+18% GST extra)
You save: ₹ 1,700.00
- Brand: Cytron
- Voltage: 12VDC
- Rated Torque: 10.0 kg.cm (0.98 N.m)
- Rated Speed: 250 RPM
- Rated Current: 5500mA
- Rated Power output: 41.3W
- Gear ratio: 24:1
- Encoder Output: 120 PPR
-
Planetary DC Geared Motor 170 RPM 27N-CM 12V IG32E-35K
SKU: 7968₹ 3,659.00₹ 2,999.00(inc GST)
₹ 2541.53 (+18% GST extra)
You save: ₹ 660.00
- Brand Name: Cytron
- Voltage: 12VDC
- Rated Torque: ~2.753 kg.cm (270 mN.m)
- Rated Speed: 170 RPM
- Rated Current: 900mA
- Rated Power: 7W
- Gear ratio: 35:1
- Encoder: 245 PPR
-
Planetary DC Geared Motor 1400 RPM 22N-CM 12V IG42E-04K
SKU: 24494₹ 6,289.00₹ 5,289.00(inc GST)
₹ 4482.2 (+18% GST extra)
You save: ₹ 1,000.00
- Brand: Cytron
- Voltage: 12VDC
- Rated Torque: 2.24 kg.cm (0.22 N.m)
- Rated Speed: 1400 RPM
- Rated Current: 5500mA
- Rated Power output: 41.3W
- Gear ratio: 4:1
- Encoder Output: 20 PPR
-
Planetary DC Geared Motor 120 RPM 176N-CM 12V IG42E-49K
SKU: 7958₹ 5,669.00₹ 4,999.00(inc GST)
₹ 4236.44 (+18% GST extra)
You save: ₹ 670.00
- Brand: Cytron
- Rated Voltage: 12VDC
- Rated Torque: ~17.94 kg.cm (1.76 N.m)
- Rated Speed: 120 RPM
- Rated Current: 5500mA
- Rated Power output: 41.3W
- Gear ratio: 49:1
- Encoder Output: 245 PPR
-
Cytron SmartDriveDuo-10 MDDS10 DC MOTOR DRIVER
SKU: 4565₹ 3,937.00(inc GST)
₹ 3336.44 (+18% GST extra)
-
Single power operation
-
Dual Channels means it can drive two brush motor independently, or mixed.
- Support Signed magnitude and Locked Anti-phase in PWM mode.
-
Two manual/test buttons for each channel.
-
Two output indicator LEDs for each channel.
-
Power, Error indicator, RUN status (Left and Right) LEDs
-
On board reset button to restart the MCU after changing operation mode.
-
Operating modes: RC (RC servo signal), Analog, PWM, simplified and packetized UART.
-
-
Auto-Calibrating Line Sensor LSS05
SKU: 4711₹ 1,039.00(inc GST)
₹ 880.51 (+18% GST extra)
-
5V power, reserve polarity protected
-
5 digital outputs representing the logic of 5 IR sensor, represented with indicator each.
-
Calibration button for easily calibrating the sensor
- Dimensions: 64x28x10 (LxWxH) mm.
- Weight: 8 gm.
-
-
Advanced Auto-Calibrating Line Sensor LSA08
SKU: 6182₹ 4,725.00(inc GST)
₹ 4004.24 (+18% GST extra)
- 8 sensor pairs spaced 16mm.
- 12V input power
- Onboard Mode and a Select button for instant configuration of LSA08
- LCD display unit showing 8 sensors analog value with bar chart and line position.
- Simple Auto-Calibration function to the line following surface.
- Low current consumption (typically 26mA)
- Works on glossy or reflective surface
- Refresh rate up to 200Hz.
-
Cytron G15 Shield
SKU: 6265₹ 892.00(inc GST)
₹ 755.93 (+18% GST extra)
-
Arduino reset button
-
4 x G15 Cube Servo ports.
-
External power port for a servo with polarity protection
-
Stackable I/O header pin
-
Selectable digital pins for the control pin with mini jumpers
-
TX and RX indicator LEDs to show communication activities, only on Rev2.0.
-
Selectable Serial pins, Either hardware serial or software serial via mini jumpers, only on Rev2.0
-
-
USB PIC Programmer – UP00B
SKU: 10109₹ 3,307.00(inc GST)
₹ 2802.54 (+18% GST extra)
- USB powered, no extra power needed to load program
- Two ZIF sockets (20 pins and 40 pins) to ease the program loading process
- Support most 8pin, 18pin, 28pin and 40pin PDIP 8 bit PIC MCU
- Support Windows XP, Vista, 7 (32 and 64-bits)
- Support Intel and AMD based system
- Support Laptop and desktop PC
-
USB ICSP PIC Programmer – UIC00B
SKU: 10053₹ 1,039.00(inc GST)
₹ 880.51 (+18% GST extra)
- Program most of the +3.3V or +5V PIC
- Compatible with PICkit2’s UART Tool and Logic Tool
- The program most of the current 8-, 16-, and 32-bit Flash PIC microcontroller
-
Compatible with Windows XP, Vista, 7, 8 and 8.1.
-
Compatible with Microchip’s PICkit 2.
-
Powered directly from the USB port.
-
NO EXTERNAL POWER REQUIRED for UIC00B to function.
-
Compatible with PICkit2’s Logic Tool and UART Tool.
-
PS2 Controller Starter Kit
SKU: 7438₹ 1,653.00(inc GST)
₹ 1400.85 (+18% GST extra)
- Stable 5V powered, low current consumption, less than 150mA.
- 1 standard PS2 controller socket.
- Communicate with host microcontroller through 5V TTL UART.
- Simple inquiry command and button status feedback for the host process.
- Vibrator motor is controllable.
- Wired or wireless PS2 controller is fully compatible.
- A small LED as the indicator for communication between SKPS and PS2 controller.
-
Planetary DC Geared Motor 60 RPM 67N-CM 12V IG32E-100K
SKU: 24492₹ 3,879.00(inc GST)
₹ 3287.29 (+18% GST extra)
- Brand: Cytron
- Voltage: 12VDC
- Rated Torque: ~6.73 kg.cm (660 mN.m)
- Rated Speed: 60 RPM
- Rated Current: 900mA
- Rated Power: 7W
- Gear ratio: 100:1
- Encoder Output: 700 (PPR) single channel output
-
Planetary DC Geared Motor 24 RPM 120N-CM 12V IG32E-264K
SKU: 24493₹ 4,504.00₹ 4,054.00(inc GST)
₹ 3435.59 (+18% GST extra)
You save: ₹ 450.00
- Brand: Cytron
- Voltage: 12VDC
- Rated Torque: 12.24 kg.cm (1200 mN.m)
- Rated Speed: 24 RPM
- Rated Current: 900mA
- Rated Power: 7W
- Gear ratio: 264:1
- Encoder Output: 1848 PPR
-
Planetary DC Geared Motor 1140 RPM 4.6N-CM 12V IG32E-05K
SKU: 24487₹ 3,664.00₹ 3,298.00(inc GST)
₹ 2794.92 (+18% GST extra)
You save: ₹ 366.00
- Brand: Cytron
- Voltage: 12V DC
- Rated Torque: 0.459 kg.cm (45 mN.m)
- Rated Speed: 1140 RPM
- Rated Current: 900 mA
- Rated Power: 7W
- Gear ratio: 5:1
- Encoder Output: 35 PPR
-
NANO32 ESP32 IoT Development Board
SKU: 24473₹ 2,913.00(inc GST)
₹ 2468.64 (+18% GST extra)
-
ESP32 SoC (System on Chip) with WiFi and Bluetooth BLE
-
40MHz Crystal for CPU, 32.768KHz for RTC and low power operation
-
4MB Flash (32MBit)
-
FTDI231 for the USB to Serial communication
-
Auto-reset for automatic flash of new program
-
On board 3.3V, 0.5A LDO, tested to work upto 1A
-
2.5dBi Peak Gain, 0.5dBi averange gain antenna
-
-
MD13S 13Amp DC Motor Driver – GROVE Compatible
SKU: 24027₹ 891.00(inc GST)
₹ 755.08 (+18% GST extra)
-
Support motor voltage ranges from 6V to 30V
-
Maximum current up to 13A continuous and 30A peak (10 seconds).
-
GROVE compatible
-
3.3V and 5V logic level input.
-
SMD compatible
- Peak Current (A): 30 (10 seconds)
- Continuous Current (A): 1
- No. of Channels: 1
-
-
ICSP Universal Socket
SKU: 10061₹ 366.00(inc GST)
₹ 310.17 (+18% GST extra)
To ease user, Cytron has created this UIC-A so that user can use any programmer regardless of the development board. For example, a development board which uses PICkit2’s socket standard, which is 6-way header pins can be programmed with UIC000B by using the UIC-A!
-
ICSP Programmer Socket – UIC-S
SKU: 10048₹ 418.00(inc GST)
₹ 354.24 (+18% GST extra)
-
No external power needed
-
Power Indicator LED on board
-
Fit perfectly with UIC00A and UIC00B
-
Support 18-pin, 28-pin, and 40-pin 8-bit PIC microcontroller.
-
Selector to program 18-pin or 28-pin&40-pin PIC
-
Come with 40-pin ZIF socket for ease of plug and unplug of PIC
-
-
G15 Driver for G15 Cube Servo
SKU: 26016₹ 490.00(inc GST)
₹ 415.25 (+18% GST extra)
-
Maximum Continuous Current: 8A
-
2 x G15 Cube Servo ports (can be daisy chained to more servos)
-
External power terminal for Cube Servo.
-
2 LEDs as logic power and servo power indicators.
-
3.3V and 5V signals compatible.
-
-
Enhanced Cytron 40Amp DC Motor Driver (Peak 80amp) MDS40B
SKU: 11648₹ 5,239.00(inc GST)
₹ 4439.83 (+18% GST extra)
-
Bi-directional control for a single brushed DC motor.
-
Support motor from 10V to 45V.
-
Maximum current up to 80A peak, reduce to 40A gradually according to temperature.
-
16 KHz switching frequency for quiet operation.
-
NO Reverse polarity protection.
-
Protection of overvoltage.
-
-
Cytron XBee Shield
SKU: 7981₹ 681.00(inc GST)
₹ 577.12 (+18% GST extra)
-
Mounts directly onto your Arduino
-
DIN and DOUT pins of XBee can be connected to either the USB’s UART pins or another digital pin on the Arduino (D0, D1, D2, D3, D8, D9, D10, D11)
-
3.3V power regulation and proper level shifting on-board communication between 5V and 3.3V
-
Extra 0.1″ spaced prototyping holes
-
Reset button brought out to shield
-
Power, DIN, DOUT, RSSI, and DIO5 indicator LEDs
-
-
Cytron SmartDriveDuo-60 MDDS60 60A (100A peak)
SKU: 8014₹ 12,064.00(inc GST)
₹ 10223.73 (+18% GST extra)
-
Input Voltage (Motor): 10 – 45VDC
- Maximum current up to 100A peak (1 second), 60A continuously, each channel.
-
Two manual/test buttons for each channel.
-
Two output indicator LEDs for each channel.
-
Suitable for combat or sumo robot.
- Battery Low Voltage Monitoring Mode
- DC Brush motor Driver, not for brushless motor
- Dual Channels, it can drive two brush motor independently, or mixed.
-
-
CYTRON SMART DRIVE MDDS30 DUAL 30A (80A Peak)
SKU: 29672₹ 5,490.00(inc GST)
₹ 4652.54 (+18% GST extra)
- Battery low voltage indicator.
- Battery over voltage indicator.
- Thermal protection.
- Current limit protection.
- Bi-directional control for dual brushed DC motor.
- Support motor voltage from 7V to 35VDC.
- Dimension: 103 x 97 x 40 (LxWxH) mm.
-
Cytron PikaBot – Maker UNO Smart Car Kit
SKU: 718386₹ 2,899.00(inc GST)
- Controller: Maker UNO
- No soldering needed, only requires to connect jumper wires
- Motor Driver: Maker Drive dual-channel DC brush motor driver
- Driven by two TT motor with pre-solder wires
- Power both controller and motor with 4 x AA battery, with battery holder too
- Comes with IR Line Sensor module, for line following
-
Cytron Maker UNO Microcontroller Board- Arduino UNO Compatible Module
SKU: 56432₹ 690.00(inc GST)
₹ 584.75 (+18% GST extra)
- SMD ATmega328P microcontroller(the same microcontroller on Arduino UNO) with Optiboot (UNO) Bootloader
- USB Programming facilitated by the CH340
- Input voltage: USB 5V, from computer, power bank or standard USB adapter
- Piezo buzzer that will act as simple audio output
- 500mA (maximum) 3.3V voltage regulator
- 0-5V outputs with 3.3V compatible inputs
- 14 Digital I/O Pins (6 PWM outputs)
- 6 Analog Inputs
- ISP 6-pin Header
-
Cytron Maker Reflect: Simplifying IR Reflectance Sensor for Beginner
SKU: 718385₹ 161.00(inc GST)
- Operating Voltage: 3.3V and 5V Compatible
- Sensing Distance (Height): 1mm to 40mm (Vcc = 5V, Blackline on a white surface)
- Features a tiny reflectance sensor
- This sensor is used in line following robot
- Fits easily in the tightest space
-
Cytron Maker Line: Simplifying Line Sensor For Beginner
SKU: 718381₹ 799.00(inc GST)
- Operating Voltage: DC 3.3V and 5V compatible (With reverse polarity protection).
- Recommended Line Width: 13mm to 30mm.
- Sensor Refresh Rate: 200Hz
- Easy calibration process.
- Supports a wide range of controllers such as Arduino, Raspberry Pi, etc.
-
Cytron Maker Drive H-Bridge Motor Driver
SKU: 381588₹ 359.00(inc GST)
₹ 304.24 (+18% GST extra)
- Dual channel, Bi-directional control motor driver
- Support motor voltage from 2.5V to 9.5VDC
- Maximum current up to 1.0A continuous and 1.5A peak (<5 seconds)
- 5V Output (200mA) to power the controller.
- Inputs compatible with 1.8V, 3.3V and 5V logic (Arduino, Raspberry Pi, etc).
- Solid state components provide faster response time and eliminate the wear and tear of mechanical relay
- Regenerative Braking
-
Cytron LCD keypad Shield High Quality
SKU: 25582₹ 619.00(inc GST)
₹ 524.58 (+18% GST extra)
- Provides a user-friendly interface that allows users to go through the menu, make selections etc.
- It consists of a 1602 white character blue backlight LCD.
- The keypad consists of 6 keys select, up, right, down, left and reset.
- To save the digital IO pins, the keypad interface only uses one ADC channel.
- The key value is read out through a 5 stage voltage divider.
-
Cytron FD04A 4-Channel Motor Driver
SKU: 16010₹ 2,362.00(inc GST)
₹ 2001.69 (+18% GST extra)
- Industrial grade PCB.
- Vmotor: 7 V to 25 V DC.
- Each component is soldered properly and tested.
- Able to drive 4 DC motor at 2.5A (peak), 1.5A continuously.
- 2 LEDs as a direction indicator for each motor.
- 1 LED as a power indicator.
- A pluggable connector for more user-friendly design.
- Fully compatible with Cytron DIY project, Flexibot – Using Transwheel (PR19).
-
Cytron ESP8266 WiFi Shield V2.0 W/ Micro SD Card Slot For Arduino Uno
SKU: 43298₹ 999.00(inc GST)
₹ 846.61 (+18% GST extra)
- Basically, Rev2.0 utilize WROOM-02 instead of ESP8266-12 as the WiFi module.
- Separate 3.3V voltage regulator for ESP8266-12 WROOM-02 module, 500mA max output.
- Each and every board is preassembled and tested before it is being shipped out to you.
- 802.11 b/g/n.
- Support Wi-Fi Direct (P2P), soft-AP.
- Integrated TCP/IP protocol stack.
-
Cytron Easy MP3 Shield
SKU: 7982₹ 1,590.00(inc GST)
₹ 1347.46 (+18% GST extra)
-
Onboard high-quality MP3 decoder.
-
Onboard dual channel/Stereo 3W differential audio amplifier for an external speaker.
- A MicroSD status LED.
-
Onboard stereo 3.5mm audio jack socket for earphones.
-
Onboard microSD socket for MP3 audio files storage.
-
The interface from Arduino, UART, selectable to use soft serial.
-
Stackable side headers.
- Supply voltage: 5V.
-
-
Cytron Dual channel 10A Motor Driver UNO Robot Controller
SKU: 49866₹ 2,510.00(inc GST)
₹ 2127.12 (+18% GST extra)
- Onboard 1A (maximum) 5V voltage regulator.
- Onboard 500mA (maximum) 3.3V voltage regulator.
- 0-5V digital outputs with 3.3V compatible inputs.
- 14 Digital I/O Pins (6 PWM outputs).(4 pin used for Motor driver)
- 6 Analog Inputs (Can be digital I/O too).
- Maximum current up to 10A continuous and 30A Peak.
- ISP 6-pin Header.
- 32k Flash Memory.
- 16MHz Clock Speed.
- R3 Shield Compatible.
-
Cytron Driver HAT-MDD10
SKU: 29670₹ 1,890.00(inc GST)
₹ 1601.69 (+18% GST extra)
- Support motor voltage ranges from 6VDC to 24VDC.
- Onboard the test button for manual control of the motor.
- Every channel output built with LED indicator.
- Current limiting at 30A.
- Operating Voltage(VDC): 6 to 24
- Peak Current (A): 30 (10 seconds)
- Continuous Current (A): 10
- No. of Channels: 2
- Operating Modes: PWM (Lock-Antiphase and Sign-Magnitude): Yes, UART: No, Analog:No, RC Servo Signal: No
-
Cytron 40 pins PIC Start-Up Kit SK40C
SKU: 10095₹ 829.00(inc GST)
₹ 702.54 (+18% GST extra)
-
ICSP connector for UIC00B -simple and fast method to load program.
-
Perfect fit for 40 pins PIC16F and PIC18F.
-
Operating Voltage Range: 7V – 15VDC
-
2 x programmable switch.
-
2 x LED indicator.
-
Exchangeable Crystal.
-
Existing pad for 16 x 2 characters LCD display.
-
UART connection to interface with other controller or even computer.
-
-
Cytron 3Amp 4V-16V Dual Channel DC Motor Driver MDD3A
SKU: 381249₹ 615.00(inc GST)
₹ 521.19 (+18% GST extra)
- Bidirectional control for two brushed DC motor.
- Control one unipolar/bipolar stepper motor.
- Operating Voltage: DC 4V to 16V
- Maximum Motor Current: 3A continuous, 5A peak
- Buck-boost regulator to produce 5V output (200mA max).
- Buttons for quick testing.
-
Cytron 2Amp Motor Driver Shield
SKU: 16014₹ 829.00(inc GST)
₹ 702.54 (+18% GST extra)
-
Logic control, 5V from Arduino main board
-
Polarity protection for External motor power input
-
2 fast test buttons for each motor channel
-
Motor Driven Voltage：6.5 to 12VDC(VIN Power Supply), 5.0 to 26VDC (External Power Source)
-
Up to 2A current each channel
-
Pin 4, 5,6,7 are used to drive two DC motor
-
Support PWM speed control
-
Support advance speed control
-
-
Cytron 25A 7V-58V DC motor driver with Switch and Potentiometer Control (MD25HV POT)
SKU: 497900₹ 3,854.00(inc GST)
₹ 3266.1 (+18% GST extra)
- Bidirectional control for one brushed DC motor.
- Maximum Motor Current: 25A continuous, 60A peak.
- 5V output for the host controller (250mA max).
- Buttons for quick testing.
- PWM frequency up to 40kHz.
- Dual Input Mode: PWM/DIR or Potentiometer/Switch Input.
-
Cytron 20Amp 6V-30V DC Motor Driver MD20A
SKU: 381393₹ 1,930.00(inc GST)
₹ 1635.59 (+18% GST extra)
- Bidirectional control for one brushed DC motor.
- Operating Voltage: DC 6V to 30V
- Maximum Motor Current: 20A continuous, 60A peak
- Buttons for quick testing.
- LEDs for motor output state.
- Overcurrent protection with active current limiting.
- Temperature protection.
- Undervoltage shutdown.
-
Cytron 10A Dual Channel DC Motor Driver Shield for Arduino Uno
SKU: 497899₹ 1,720.00(inc GST)
₹ 1457.63 (+18% GST extra)
- Bidirectional control for two brushed DC motor.
- Control one unipolar/bipolar stepper motor.
- Buck regulator to produce 5V output (500mA max).
- Buttons for quick testing.
- LEDs for motor output state.
-
Cytron 10 A Switch Control Potentiometer DC Motor Driver (MD10POT)
SKU: 234226₹ 790.00(inc GST)
₹ 669.49 (+18% GST extra)
The MD10-POT control circuit is designed to enable the speed to be controlled via a potentiometer (10K Ohm) which is included in the package. It does not work with analog voltage from an external controller The 3-way rocker switch is used for start/stop and direction control.
-
CIKU PIC PIC18F4550 based Arduino form factor starter kit
SKU: 10107₹ 1,249.00(inc GST)
₹ 1058.47 (+18% GST extra)
-
Comes with pre-programmed PIC18F4550 with USB bootloader.
-
PIC18F4550 running at 48MHz (after PLL with 10MHz external crystal).
-
Power via USB or external DC adapter (7 – 12V).
-
On board 5V 800mA (Max 1A) voltage regulator.
-
On board 3.3V 500mA (Max 500mA) voltage regulator.
-
USB mini-B receptor for USB connection.
-
20 digital I/O pins.
-
6 analog input pin.
-
2 PWM output pin.
-
-
40 pins PIC Start-Up Kit Combo 2 SK40C + PIC18F4550 (SK40C2)
SKU: 10105₹ 1,459.00(inc GST)
₹ 1236.44 (+18% GST extra)
-
ICSP connector for UIC00B -simple and fast method to load program.
-
Perfect fit for 40 pins PIC16F and PIC18F.
-
2 x programmable switch.
-
2 x LED indicator.
-
Exchangeable Crystal.
-
Existing pad for 16 x 2 characters LCD display.
-
UART connection to interface with other controller or even computer.
-
USB on board for certain PIC18F.
-
-
40 pins PIC Start-Up Kit Combo 1 – SK40C PIC16F877A (SK40C1)
SKU: 10097₹ 1,249.00(inc GST)
-
ICSP connector for UIC00B -simple and fast method to load program.
-
Perfect fit for 40 pins PIC16F and PIC18F.
-
2 x programmable switch.
-
2 x LED indicator.
-
Exchangeable Crystal.
-
Existing pad for 16 x 2 characters LCD display.
-
-
40 Pins dsPIC Start-Up Kit – SKDS40A
SKU: 10086₹ 1,144.00(inc GST)
₹ 969.49 (+18% GST extra)
-
ICSP connector for UIC00A /B-simple and fast method to load program.
-
Perfectly fit for 40 pins dsPIC (16-bit), NOT for the 40-pins 8-bit PIC.
-
2 x programmable switch.
-
2 x programmable LED indicator.
-
Changeable Crystal – default 10MHz.
-
Existing pad for 16 x 2 characters LCD display.
-
-
28 Pins PIC Start-up Kit – SK28A
SKU: 10080₹ 724.00(inc GST)
₹ 613.56 (+18% GST extra)
-
Industrial grade PCB.
-
Every board is being tested before it is shipped out.
-
Compact platform and breadboard-friendly
-
Suitable for hobbyists and expert.
-
Save development and soldering time.
-
Turn pin for crystal comes with 20MHz Crystal by default, the user may use crystal at various frequencies
-
Mini USB socket on board may use PIC18F2550 for USB device development, example USB Bootloader.
-
2×8 Character Parallel LCD pad ready (optional).
-
-
18 Pins PIC Start-up Kit – SK18B
SKU: 10064₹ 619.00(inc GST)
₹ 524.58 (+18% GST extra)
-
Compact, powerful, flexible and robust start-up platform.
-
No extra components required for the PIC to function.
-
No more frustrated work plugging PIC out and back for re-programming.
-
Perfectly fit for 18 pins PIC16F MCU.
-
With UIC00A, the program can be loaded in less than 4 seconds.
-
On/Off switch for main power
-
DC adaptor socket as power input
-
-
16-bit or 32-bit PIC Start-Up Kit – SK1632
SKU: 10062₹ 628.00(inc GST)
₹ 532.2 (+18% GST extra)
-
Input voltage range: 7V to 15VDC.
-
1 x Programmable push button (digital input, connected to A1)
-
1 x Programmable LED (active high, connected to A0)
-
Replaceable Crystal (default 8MHz)
-
Ready pads for 2×8 Character parallel interface LCD
-
USB micro B socket for PIC that supports USB peripheral
-
USB bootloader may be utilized if needed
-
