Motor Drivers
Showing 97–144 of 190 results
-
Stepper Motor Drivers
TMC2100 Stepper Motor Driver, Module
SKU: 1121430- This driver has 200 steps per revolution in full step (1.8 degrees per step).
- Allowable continuous current per phase: 1.25A (RMS) or 1.77A (max)
- The maximum current in the short term for each phase: 2.5A
- Motor voltage: 5.5 to 46 V
- StealthChop mode to reduce noise
- SpreadCycle mode to increase torque
SKU: 1121430 -
Cytron Motor Drivers
Cytron 2Amp Motor Driver Shield
SKU: 16014-
Logic control, 5V from Arduino main board
-
Polarity protection for External motor power input
-
2 fast test buttons for each motor channel
-
Motor Driven Voltage:6.5 to 12VDC(VIN Power Supply), 5.0 to 26VDC (External Power Source)
-
Up to 2A current each channel
-
Pin 4, 5,6,7 are used to drive two DC motor
-
Support PWM speed control
-
Support advance speed control
SKU: 16014 -
-
Dimension Engineering Motor Drivers
BattleSwitch radio controlled 10A relay (Dimension Engineering)
SKU: 6314- 30mA typical draw from receiver
- 12-inch servo pigtail
- Switching Voltage: 10A @ 28VDC, 12A @ 120VAC, 10A @ 240VAC.
- Relay resistance: 100 mΩ max
- operating voltage: 3.5V to 5.5V (on servo pigtail)
SKU: 6314 -
Cytron Motor Drivers
Cytron Arduino PS2 Shield
SKU: 2506- 5V powered low current consumption.
- Simple to use UART protocol
- Vibrator motor on PS2 is controllable.
- Wired and Wireless PS2 controller is supported.
- PS2 Controller will automatically operate in analog mode.
- A status LED
- Jumper selector to select different UART Baud Rate (9600, 57600, 115200).
- Jumper selectors to select different digital pin as UART TX and RX pin.
SKU: 2506 -
-
Cytron Motor Drivers
8 Channel Servo Controller SC08A
SKU: 7978-
Resolution: 8000 steps = 0.25us.
-
UART: 9600 baud rate.
-
Servo pulse range: 0.5ms to 2.5ms.
-
Dimension :Â 48 x 46 x 14 (LxWxH) mm.
- 8 channels: Servo-driven independently.
-
Extendable to 16 Channels: Two controllers linked together to drive 16 servos.
-
Optional Position Reporting: User may request the position of an individual servo.
SKU: 7978 -
-
Cytron Motor Drivers
Cytron 10A Dual Channel DC Motor Driver Shield for Arduino Uno
SKU: 497899- Bidirectional control for two brushed DC motor.
- Control one unipolar/bipolar stepper motor.
- Buck regulator to produce 5V output (500mA max).
- Buttons for quick testing.
- LEDs for motor output state.
SKU: 497899 -
Cytron Motor Drivers
Cytron FD04A 4-Channel Motor Driver
SKU: 16010- Industrial grade PCB.
- Vmotor: 7 V to 25 V DC.
- Each component is soldered properly and tested.
- Able to drive 4 DC motor at 2.5A (peak), 1.5A continuously.
- 2 LEDs as a direction indicator for each motor.
- 1 LED as a power indicator.
- A pluggable connector for more user-friendly design.
- Fully compatible with Cytron DIY project, Flexibot – Using Transwheel (PR19).
SKU: 16010 -
Brushed / Brushless DC motor Driver
SmartElex Wireless Remote Control with NRF24L01+PA+LNA SMA Antenna
Brushed / Brushless DC motor DriverSmartElex Wireless Remote Control with NRF24L01+PA+LNA SMA Antenna
SKU: 664890- It uses 2.4GHz global open ISM band, with license-free.
- Operating Range: 1Km
- Antenna Gain (peak): 2Dbi.
- Transmit power is greater than +20 dBm.
- Support six-channel data reception.
SKU: 664890 -
Cytron Motor Drivers
Cytron ESP8266 WiFi Shield V2.0 W/ Micro SD Card Slot For Arduino Uno
SKU: 43298- Basically, Rev2.0 utilize WROOM-02 instead of ESP8266-12 as the WiFi module.
- Separate 3.3V voltage regulator for ESP8266-12 WROOM-02 module, 500mA max output.
- Each and every board is preassembled and tested before it is being shipped out to you.
- 802.11 b/g/n.
- Support Wi-Fi Direct (P2P), soft-AP.
- Integrated TCP/IP protocol stack.
SKU: 43298 -
Cytron Motor Drivers
USB ICSP PIC Programmer – UIC00B
SKU: 10053- Program most of the +3.3V or +5V PIC
- Compatible with PICkit2’s UART Tool and Logic Tool
- The program most of the current 8-, 16-, and 32-bit Flash PIC microcontroller
-
Compatible with Windows XP, Vista, 7, 8 and 8.1.
-
Compatible with Microchip’s PICkit 2.
-
Powered directly from the USB port.
-
NO EXTERNAL POWER REQUIRED for UIC00B to function.
-
Compatible with PICkit2’s Logic Tool and UART Tool.
SKU: 10053 -
Cytron Motor Drivers
Cytron Dual channel 10A Motor Driver UNO Robot Controller
SKU: 49866- Onboard 1A (maximum) 5V voltage regulator.
- Onboard 500mA (maximum) 3.3V voltage regulator.
- 0-5V digital outputs with 3.3V compatible inputs.
- 14 Digital I/O Pins (6 PWM outputs).(4 pin used for Motor driver)
- 6 Analog Inputs (Can be digital I/O too).
- Maximum current up to 10A continuous and 30A Peak.
- ISP 6-pin Header.
- 32k Flash Memory.
- 16MHz Clock Speed.
- R3 Shield Compatible.
SKU: 49866 -
Brushed / Brushless DC motor Driver
SmartElex 10D Smart Motor Driver (Powered by Raspberry Pi)
SKU: 1734771- Onboard 5V 3A Buck Converter.
- Continuous 10A maximum current without Heatsink
- Two brushed DC motor Bidirectional control.
- Current limiting at 35A.
- PWM and direction-controlled driving of four externally powered NMOS transistors
- Type-C USB for SERIAL Mode
SKU: 1734771 -
Stepper Motor Drivers
TMC2209 Stepper Motor Driver Module with Heatsink
SKU: 1555083- Operating Voltage: 4.5V to 28V DC
- Input Signal Logic Voltage: 3.3V to 5V DC
- Maximum Peak Current: 2A per phase (use with Heatsink and Fan only)
- Maximum Continuous Current: 2A
- Compatibility: 3V3 and 5V microcontrollers
SKU: 1555083 -
Cytron Motor Drivers
Cytron Driver HAT-MDD10
SKU: 29670- Support motor voltage ranges from 6VDC to 24VDC.
- Onboard the test button for manual control of the motor.
- Every channel output built with LED indicator.
- Current limiting at 30A.
- Operating Voltage(VDC): 6 to 24
- Peak Current (A): 30 (10 seconds)
- Continuous Current (A): 10
- No. of Channels: 2
- Operating Modes: PWM (Lock-Antiphase and Sign-Magnitude): Yes, UART: No, Analog:No, RC Servo Signal: No
SKU: 29670 -
-
Servo Motor Drivers
USB 32Ch Servo Motor Controller Board support PS2 WIFI with USB Cable
SKU: 494926- Baud rate (USB): 115200
- Baud rate (bluetooth, UART): 9600
- Storage Flash capacity: 16M
- Mode to choose: 4 types
- Simultaneous controlling servo number: 32 channel
- Max action groups: 256 groups
- Communication agreement: UART
- Cross platform operation, can support WindowsXP, WindowsVisit, Windows7, Windows8, Windows10, Linux,FreeBsd, MAC OS, Android
SKU: 494926 -
-
Pololu Motor Drivers
Pololu DRV8835 Dual Motor Driver Carrier
SKU: 1607672- Under-voltage lockout on the logic supply and protection against over-current and over-temperature
- Reverse-voltage protection on the motor supply
- Compact size (0.7″×0.4″) with the form factor of a 14-pin DIP package
- Inputs are 3V- and 5V-compatible
SKU: 1607672 -
Servo Motor Drivers
Waveshare Serial Bus Servo Driver Board, Integrates Servo Power Supply And Control Circuit, Applicable for ST/SC Series Serial Bus Servos
Servo Motor DriversWaveshare Serial Bus Servo Driver Board, Integrates Servo Power Supply And Control Circuit, Applicable for ST/SC Series Serial Bus Servos
SKU: 1782919- Power Supply DC: 9~12.6V (ST series servo)
- Power Supply Connector: 5.5 × 2.1mm DC
- Communication Interface: UART
- Dimensions: 42.00 × 33.00mm
- Mounting Hole Size: 2.50mm
- Mounting Hole Spacing: 37.00 × 28.00mm
SKU: 1782919 -
Brushed / Brushless DC motor Driver
SeeedStudio Grove I2C Motor Driver (TB6612FNG)
SKU: 672607- MCU Operating Voltage: 3.3V / 5V
- Motor Supply Voltage: 2.5 ~ 13.5 (5V Typical, 15V Max.)
- Output Current: 1.2 A(ave)/3.2 A (peak)
- Switching Frequency: 100kHz
- Logic Interface: I2C
- I2C Address: 0x14 (default)
SKU: 672607 -
Pololu Motor Drivers
Pololu DRV8834 Low-Voltage Stepper Motor Driver Carrier
SKU: 1607671- Built-in regulator (no external logic voltage supply needed)
- Short-to-ground, short-to-supply, and shorted-load protection
- 4-layer, 2Â oz copper PCB for improved heat dissipation
- Exposed solderable ground pad below the driver IC on the bottom of the PCB
- Simple step and direction control interface
SKU: 1607671 -
Dimension Engineering Motor Drivers
Sabertooth Dual 5A Motor Driver for R/C
SKU: 4689- Operating Voltage(VDC): 6-18
- Peak Current (A): 10
- Continuous Current (A): 5
- No. of Channels: 2
- Synchronous regenerative drive
- Ultra-sonic switching frequency
- Thermal and overcurrent protection
- Lithium protection mode-compatible with: 6-12 cell NiMH or NiCd, 2s-4s LiPo, 6V or 12V lead acid (not 18+V lead acid!)
SKU: 4689 -
Stepper Motor Drivers
BIGTREETECH BTT TMC2226 V1.0 Stepper Motor Driver
SKU: 1604112- 2-phase stepper motors up to 2.8A coil current (peak), 2A RMS
- STEP/DIR Interface with 8, 16, 32 or 64 microstep pin setting
- Smooth Running 256 microsteps by MicroPlyer interpolation
- StealthChop2 silent motor operation
- Spread Cycle highly dynamic motor control chopper
- StallGuard4 load and stall detection for StealthChop
- Cool Step current control for energy savings up to 75%
- Low Power Standby to fit standby energy regulations
SKU: 1604112 -
-
-
Pololu Motor Drivers
Pololu DRV8256E Single Brushed DC Motor Driver Carrier
SKU: 1607670- built-in protection against reverse-voltage, under-voltage, over-current, and over-temperature
- simple two-pin speed direction interface
- Under-voltage lockout and protection against over-current and over-temperature
- Simple interface requires only two I/O lines (one for direction and another for speed)
SKU: 1607670 -
Stepper Motor Drivers
MA860H Digital Stepper Micro-Step CNC Motor Driver 50-110 VDC with 1.8-7.5A
SKU: 6747- Supply voltage up to 80VAC or +110VDC
- Output current up to 7.2A
- Pulse input frequency up to 300 KHz
- 16 selectable resolutions in decimal and binary, up to 51,200 steps/rev
- Suitable for 2-phase and 4-phase motors
- Dimensions: 118×75.5×34 (LxWxH) mm
SKU: 6747 -
Brushed / Brushless DC motor Driver
Forward/Reverse Motor Controller Board 12V 24V Motor Two Relay Delay Timing Cycle YYB-5 Module
Brushed / Brushless DC motor DriverForward/Reverse Motor Controller Board 12V 24V Motor Two Relay Delay Timing Cycle YYB-5 Module
SKU: 1794358- Current Rating: 30 Amps
- Operation Mode: Automatic
- Coil Voltage: 24 Volts
- Model: YYB-5
- Input voltage: DC/ AC7V~27V
- Time range: 0.1 seconds to 999 minutes
SKU: 1794358 -
Stepper Motor Drivers
BIGTREETECH BTT TMC2130 V3.0 Stepper Motor Driver
SKU: 16116641. Up to 256 subdivisions;
2. Support SPI interface control;
3. Do not lose step when driving under high load;
4. Logic voltage: 3.3V/5V;
5. Input voltage range: 12V/24V DC;
6. Motor operating current 1.2a (peak 2A) can be adjusted
7. Spreadcycle ensures that the stepper motor has a smooth transition without dead zone current when passing zero.SKU: 1611664 -
Stepper Motor Drivers
Two Trees – Stepper Motor Driver DM556 5.6A
SKU: 1645774- Supply voltage up to +50 VDC
- Output current programmable, from 0.5A to 5.6A via DIP switches
- Pulse input frequency up to 200 kHz
- All Digital Inputs are TTL compatible and optically isolated input
- Automatic idle-current reduction
- Suitable for 2-phase and 4-phase motors
- Support PUL/DIR and CW/CCW modes
SKU: 1645774 -
Cytron Motor Drivers
Cytron MDS160A SmartDrive160 160AMP Dc Motor Driver (Peak 190Amp)
SKU: 2784- Bi-directional control for a single brushed DC motor.
- Support input voltage from 8V to 28V.
- Maximum current up to 190A peak (1 minute), 175A (2 minutes) or 160A (continuously).
- 16 KHz switching frequency for quiet operation.
- LiPo battery low voltage warning.
- Thermal protection.
SKU: 2784 -
Brushed / Brushless DC motor Driver
TB6612 D1 Motor Driver Shield
SKU: 1031048- Interface: I2C
- Power supply voltage: VM = 15V max
- Output current: Iout = 1.2A ( average ) / 3.2A ( peak )
- Standby control to save power CW / CCW / short brake / stop motor control modes
- Standby control mode-I2C mode: control TB6612’s STBY with I2C protocol
- IO mode: control TB6612’s STBY with Spin
SKU: 1031048 -
Cytron Motor Drivers
Cytron Uno Board ATmega328 Microcontroller (Arduino Compatible)
SKU: 766269- A better version of Arduino Uno
- SMD ATmega328 microcontroller with Optiboot (UNO) Bootloader
- USB Programming Facilitated by the Ubiquitous FTDI FT231X (more stable)
- Input voltage: DC7-15V
- 14 Digital I/O Pins (6 PWM outputs)
SKU: 766269 -
Brushed / Brushless DC motor Driver
Sabertooth Dual 5A Motor Driver
SKU: 4686- Input Voltage: 6V to 18V
- Compatible with: 6-12 cell NiMH or NiCd, 2s-4s LiPo
- 5A continuous per channel, 10A peak
- Synchronous regenerative drive
- Ultra-sonic switching frequency
- Thermal and overcurrent protection
- Lithium protection mode
SKU: 4686 -
Stepper Motor Drivers
MKS SBASE V1.3 32-bit Open Source Smoothieboard
SKU: 766364- Â 32bit 100M Cortex-M3 MCU-LPC 1768
- High-performance
- Support highly modular open source firmware Smoothieware
- Easy for secondary development
- Â Support network function, then proceed remote control via IE Explorer.
SKU: 766364 -
Brushed / Brushless DC motor Driver
Motor Forward and Reverse Rotation Controller Board Solenoid Valve Pump Remote Control Circuit Switch Two-Wire
Brushed / Brushless DC motor DriverMotor Forward and Reverse Rotation Controller Board Solenoid Valve Pump Remote Control Circuit Switch Two-Wire
SKU: 1794493- Product name: forward motor, reverse rotation motor control board module
- Product size: 91mm * 42mm * 19 mm (length, width and height)
- Voltage range: DC 7~30v
- Current range: within 10a; Two wire motor forward and reverse rotation
SKU: 1794493