SmartElex
Showing 1–48 of 93 results
-
Smart Motor Drivers
SmartElex 15D Smart Motor Driver (Powered By Raspberry Pi)
SKU: 1734772- Support motor voltage from 7V to 22V.
- Onboard Low, Internal resistance MOSFETs are switched at 16 KHz frequency.
- Overcurrent and Thermal protection.
- Multiple input modes: RC, Analog, PWM, Serial Packetized.
- On-board push buttons for test and manual operation.
- Type-C USB for SERIAL Mode
SKU: 1734772 -
Brushed / Brushless DC motor Driver
SmartElex 30D Smart Motor Driver (Powered by Raspberry Pi)
SKU: 1734773- Supplying 30 amps continuously with peak currents up to 85 amps (2 Sec) per channel.
- Support motor voltage from 7V to 28V.
- Onboard Low Internal resistance MOSFETs are switched at 16KHz frequency.
- Overcurrent protection and indication.
- Thermal protection.
- Type-C USB for SERIAL Mode
SKU: 1734773 -
8051 Development Board
SmartElex AT89S52 Development Board with LCD
SKU: 464732- Onboard 5V regulator (78M05) circuit.
- On-Board power supply on-off switch
- On-Board DC motor Driver L298P
- On-Board 4×4 Matrix Keypad.
- On-Board 4 bit 16×2 LCD Display.
- 0592MHz crystal.
- Port extensions for all ports with detailed pin labelling for easy identification of pins
- Onboard USB TO Serial – CH340 Chip.
- On-board Micro USB USBASP for loading HEX file.
SKU: 464732 -
Brushed / Brushless DC motor Driver
SmartElex Wireless Remote Control with NRF24L01+PA+LNA SMA Antenna
Brushed / Brushless DC motor DriverSmartElex Wireless Remote Control with NRF24L01+PA+LNA SMA Antenna
SKU: 664890- It uses 2.4GHz global open ISM band, with license-free.
- Operating Range: 1Km
- Antenna Gain (peak): 2Dbi.
- Transmit power is greater than +20 dBm.
- Support six-channel data reception.
SKU: 664890 -
Battery Chargers, Battery Charging Boards
SmartElex 1S 18650 Li-ion Battery Charger/Discharger
SKU: 611923- Input Voltage: 4.5V ~ 5.5V.
- Input Interface: 5VDC Micro USB and DC JACK input.
- On-board Battery compatible: – 18650 Li-ion cell.
- Charge Current: up to 1A.
- Over-voltage detection: 4.2V.
- Under-voltage detection: 2.8V.
- Output Interface: – 2 Pin Connector with a properly marked positive and negative signs on PCB.
- LED indicator: Input Power status/ Charging /Charge complete / Battery detects / under-voltage.
SKU: 611923 -
Brushed / Brushless DC motor Driver
SmartElex 10D Smart Motor Driver (Powered by Raspberry Pi)
SKU: 1734771- Onboard 5V 3A Buck Converter.
- Continuous 10A maximum current without Heatsink
- Two brushed DC motor Bidirectional control.
- Current limiting at 35A.
- PWM and direction-controlled driving of four externally powered NMOS transistors
- Type-C USB for SERIAL Mode
SKU: 1734771 -
Shield for Arduino
SmartElex PS2 Sheild for Arduino
SKU: 217461- Simple to use UART protocol
- Vibrator motor on PS2 is controllable.
- Wired and Wireless PS2 controller is supported.
- PS2 Controller will automatically operate in analog mode. (Default)
- A status LED
- Jumper selector to select different UART Baud Rate (74880 (Default), 9600, 57600, 115200). Default: – when no jumper is attached.
- Jumper selectors to select different digital pin as UART – TX and RX pin.
SKU: 217461 -
-
-
-
USB Interface Module
SmartElex IOIO OTG for Android
SKU: 86932- Recommended Input Voltage: 12V
- Input Voltage Range: 5-15V
- 2 Pin 2mm SMD JST Right-angle Connector for Input supply
- On-board TPS62133RGTT Synchronous step down DC-DC converter.
- Power Status LED (RED)
- Micro USB for Communication with Android.
- One start LED connected to boot pin (RC12 =Pin no. 39).
- User Switch SW1, SW2 connected to any port pin through SW1, SW2 Jumper respectively.
SKU: 86932