Motor Driver
-
16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
₹ 350.00(inc GST)
₹ 296.61 (+18% GST extra)
- Adjustable frequency PWM up to about 1.6 KHz
- 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
- Configurable push-pull or an open-drain output
- The output enable pin to quickly disable all the outputs
- Terminal block for power input
- Reverse polarity protection on the terminal block input
- Green power-good LED
-
20A PWM DC Motor Speed Regulator Module (9V, 12V, 24V, 36V, 48V, 60V)
₹ 590.00(inc GST)
₹ 500 (+18% GST extra)
- Adjustable speed range: 0%-100%.
- Speed adjustment way: Potentiometer.
- Output voltage: Linear under load.
- Speed control type: Basins.
- Output voltage: Load Linear
- Type: Adjusting flow
- The motor running condition adjustment: Forward / Stop / Reverse
-
5-36v Switch Drive High-power MOSFET Trigger Module
₹ 150.00(inc GST)
₹ 127.12 (+18% GST extra)
This 5-36v Switch Drive High-power MOSFET Trigger Module can control the output of power equipment, motors, light bulbs, LED lights, DC motors, micro-pumps, solenoid valves, PWM, motor speed control, lamp brightness. etc.
-
A4988 driver Stepper Motor Driver- Normal Quality
₹ 116.00(inc GST)
₹ 98.31 (+18% GST extra)
- Supply Voltage : 8-35 VDC.
- Current : 1.0A (no heatsink ).
- Current : 2.0A (with heat-sinking).
- logic input : 3 – 5.5V .
- Automatic current decay mode detection / choice.
- Mixed with slow current decay mode.
-
CNC shield V3 for Engraving Machine 3D Printer A4988 DRV8825 driver expansion board
₹ 190.00(inc GST)
₹ 161.02 (+18% GST extra)
- Latest Arduino CNC Shield Version 3.10
- GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
- Coolant enable
- Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
- Compact design.
- 4-Axis support (X, Y, Z, A-Can duplicate X, Y, Z or do a full 4th axis with custom firmware using pins D12 and D13)
- 2 x End stops for each axis (6 in total)
-
Cytron 2Amp Motor Driver Shield
₹ 829.00(inc GST)
₹ 702.54 (+18% GST extra)
-
Logic control, 5V from Arduino main board
-
Polarity protection for External motor power input
-
2 fast test buttons for each motor channel
-
Motor Driven Voltage:6.5 to 12VDC(VIN Power Supply), 5.0 to 26VDC (External Power Source)
-
Up to 2A current each channel
-
Pin 4, 5,6,7 are used to drive two DC motor
-
Support PWM speed control
-
Support advance speed control
-
-
Cytron Dual channel 10A Motor Driver UNO Robot Controller
₹ 2,510.00(inc GST)
₹ 2127.12 (+18% GST extra)
- Onboard 1A (maximum) 5V voltage regulator.
- Onboard 500mA (maximum) 3.3V voltage regulator.
- 0-5V digital outputs with 3.3V compatible inputs.
- 14 Digital I/O Pins (6 PWM outputs).(4 pin used for Motor driver)
- 6 Analog Inputs (Can be digital I/O too).
- Maximum current up to 10A continuous and 30A Peak.
- ISP 6-pin Header.
- 32k Flash Memory.
- 16MHz Clock Speed.
- R3 Shield Compatible.
-
Cytron FD04A 4-Channel Motor Driver
₹ 2,362.00(inc GST)
₹ 2001.69 (+18% GST extra)
- Industrial grade PCB.
- Vmotor: 7 V to 25 V DC.
- Each component is soldered properly and tested.
- Able to drive 4 DC motor at 2.5A (peak), 1.5A continuously.
- 2 LEDs as a direction indicator for each motor.
- 1 LED as a power indicator.
- A pluggable connector for more user-friendly design.
- Fully compatible with Cytron DIY project, Flexibot – Using Transwheel (PR19).
-
Cytron SmartDriveDuo-60 MDDS60 60A (100A peak)
₹ 12,064.00(inc GST)
₹ 10223.73 (+18% GST extra)
-
DC Brush motor Driver, not for brushless motor
-
Input Voltage (Motor): 7 – 45VDC
-
Two manual/test buttons for each channel.
-
Two output indicator LEDs for each channel.
-
Suitable for combat or sumo robot.
- Battery Low Voltage Monitoring Mode
-
-
DC Motor PWM Speed Regulator 1.8V, 3V, 5V, 6V, 12V-2A speed control switch function
₹ 216.00(inc GST)
₹ 183.05 (+18% GST extra)
- Input supply voltage: 1.8V- 15V DC.
- The maximum output power: 30W
- Output current : 2A(Max).
- With resettable fuse.
- Equipped with LED indicator.
- Potentiometer with switch function for PWM adjustment.
-
DRV8825 Stepper Motor Driver with Aluminum Heat Sink- Good Quality
₹ 175.00(inc GST)
₹ 148.31 (+18% GST extra)
- Supply Voltage: 8.2 – 42 VDC.
- Current Capacity : 2.2A max(24V).
- Continuous current per phase: 1.5 A.
- Minimum Logic voltage: 2.5V.
- Maximum Logic Voltage: 5V.
- Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32.
- Dimensions : 15 x 20 mm.
- Weight: 4 gm.
-
Enhanced Cytron 40Amp DC Motor Driver (Peak 80amp) MDS40B
₹ 5,239.00(inc GST)
₹ 4439.83 (+18% GST extra)
-
Bi-directional control for a single brushed DC motor.
-
Support motor from 10V to 45V.
-
Maximum current up to 80A peak, reduce to 40A gradually according to temperature.
-
16 KHz switching frequency for quiet operation.
-
NO Reverse polarity protection.
-
Protection of overvoltage.
-
-
IRF520 MOSFET Driver Module for Arduino ARM Raspberry pi
₹ 110.00(inc GST)
₹ 93.22 (+18% GST extra)
- Voltage: 3.3 – 5V.
- Ports: Digital Level.
- Output load voltage: 0-24 V.
- Output load current: <5A (1A above need to add heat sink).
- Platform: Arduino, MCU, ARM, raspberry pi.
- Using original IRF520 Power MOS, you can adjust the output PWM
-
L293D Motor Driver/Servo Shield for Arduino
₹ 179.00(inc GST)
₹ 151.69 (+18% GST extra)
- 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
- 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes.
- Can run motors on 4.5VDC to 25VDC.
- Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
- Pull down resistors keep motors disabled during power-up
- Big terminal block connectors to easily hook up wires (18-26AWG) and power
- 2-pin terminal block and jumper to connect external power, for separate logic/motor supplies
-
L298N 2A Based Motor Driver Module – Good Quality
₹ 159.00(inc GST)
₹ 134.75 (+18% GST extra)
- Current Sense for each motor.
- Heatsink for better performance.
- Power-On LED indicator.
- Double H bridge Drive Chip: L298N.
- Operating Voltage(VDC): 5~35
- Peak Current (A): 2
- Continuous Current (A): 0-36mA
- No. of Channels: 2
- Over-Current Protection (A): Yes
- Thermal Protection: Yes
-
L298N Dual H Bridge DC/Stepper Motor Driver Controller Module
₹ 199.00(inc GST)
₹ 168.64 (+18% GST extra)
- Driver chip: L298N Dual H Bridge
- Supply voltage: VMS 5V – 35V
- Peak current IO: 2A per bridge
- Max power consumption: 20W
- Provides 4 LEDs that reflect the state of the control logic
- Independent direction, speed, and braking for each motor
-
MD13S 13Amp DC Motor Driver – GROVE Compatible
₹ 891.00(inc GST)
₹ 755.08 (+18% GST extra)
-
Support motor voltage ranges from 6V to 30V
-
Maximum current up to 13A continuous and 30A peak (10 seconds).
-
GROVE compatible
-
3.3V and 5V logic level input.
-
SMD compatible
- Peak Current (A): 30 (10 seconds)
- Continuous Current (A): 1
- No. of Channels: 1
-
-
SmartElex 10D DC Motor Driver HAT for Raspberry Pi
₹ 1,189.00(inc GST)
₹ 1007.63 (+18% GST extra)
- Wide 6V to 28V motor Operating Voltage.
- Continuous 10A maximum current without Heatsink and 30A peak current for 10 Seconds.
- Two brushed DC motor Bidirectional control.
- Current limiting at 35A.
- PWM frequency up to 32KHz
- Support TTL PWM from the microcontroller
- Internal thermal shutdown
- Under-voltage lockout
- PWM and direction controlled driving of four externally powered NMOS transistors
- 3V and 5V logic level input.
-
SmartElex 10S DC Motor Driver HAT
₹ 749.00(inc GST)
₹ 634.75 (+18% GST extra)
- Wide 6V to 28V motor Operating Voltage.
- One brushed DC motor Bidirectional control.
- Current limiting at 35A.
- PWM frequency up to 32KHz
- Support TTL PWM from the microcontroller
- Internal thermal shutdown
- Under-voltage lockout
-
TB6560 Driver Board 3A CNC Router Single 1 Axis Controller Stepper Motor
₹ 470.00(inc GST)
₹ 398.31 (+18% GST extra)
- Driver Chip: TB6560AHQ
- Operating Voltage: 10-35V
- Nominal Voltage: 24V
- With the large heat sink to ensure good heat dissipation
- 6N137 high-speed OptoCoupler, to ensure a high speed without step out.
The product is already in the wishlist! Browse Wishlist -
TB6600 stepper motor Driver Controller 4.5A 8~50V TTL 16 Micro-Step CNC Single-Axis
₹ 649.00(inc GST)
₹ 550 (+18% GST extra)
- Supply Voltage: 8V – 50V DC (36V recommended).
- Output current: 0.3A – 4.5A (peak value of 5A).
- Micro Step: 1, 2, 8, 16.
- Maximum PWM frequency: 200kHz.
- Adjustments for the maximum current of the LED: 1A, 2.2A, 3.3A, 4.5A.
- Operating temperature: -10 to + 45 ° С.
-
TB6600 Stepper Motor Driver Controller 4A 9~42V TTL 16 Micro-Step CNC 1 Axis
₹ 649.00(inc GST)
₹ 550 (+18% GST extra)
- Input Current: 0~5A
- Output Current: 0.5~4.0A
- Control Signal: 3.3~24V
- Power (MAX): 160W
- Micro Step: 1, 2/A, 2/B, 4, 8, 16, 32
- Temperature: -10~45℃
- H bridge bipolar constant current drive.
-
ULN2003 Driver Module Stepper Motor Driver
₹ 79.00(inc GST)
₹ 66.95 (+18% GST extra)
- 5-12V power supply
- 4-way signal indicator
- Chip all the pins have Input leads Mounted for easy connection to use
- XH-5P socket can be connected directly 28BYJ-48 Model stepper motor
- Dimensions: 32 x 18 x 11mm (LxWxH)
- Weight: 3 gm
-
ULN2003 Driver Module Stepper Motor Driver Board
₹ 79.00(inc GST)
₹ 66.95 (+18% GST extra)
- ULN2003A motor driver chip
- Chip all the pins already leads for easy connection to use
- 5-12V power supply
- 4-way signal indicator
- Step angle: 5.625 x 1 / 64
- Reduction ratio: 1 / 64
- Phase: 4
- Current / Phase: 5V
-
MA860H Digital Stepper Micro-Step CNC Motor Driver 50-110 VDC with 1.8-7.5A
₹ 6,667.00(inc GST)
₹ 5650 (+18% GST extra)
- Supply voltage up to 80VAC or +110VDC
- Output current up to 7.2A
- Pulse input frequency up to 300 KHz
- 16 selectable resolutions in decimal and binary, up to 51,200 steps/rev
- Suitable for 2-phase and 4-phase motors
- Dimensions: 118×75.5×34 (LxWxH) mm
-
Leadshine DM542 Digital Stepper Motor Driver
₹ 2,921.00(inc GST)
₹ 2475.42 (+18% GST extra)
- Good high-speed performance
- Supply voltage up to +50VDC
- Output current up to 4.2A
- Pulse frequency up to 300 KHz
- Automatic idle-current reduction
- 3-state current control technology
- Self-adjustment technology
- Pure-sinusoidal current control technology
-
A4988 driver Stepper Motor Driver- Good Quality
₹ 134.00(inc GST)
₹ 113.56 (+18% GST extra)
- Supply Voltage : 8-35 VDC.
- Current : 1.0A (no heatsink ).
- Current : 2.0A (with heat-sinking).
- logic input : 3 – 5.5V .
- Automatic current decay mode detection / choice.
- Mixed with slow current decay mode.
-
DRV8825 Stepper Motor Driver with Aluminum Heat Sink
₹ 160.00(inc GST)
₹ 135.59 (+18% GST extra)
- Supply Voltage: 8.2 – 42 VDC.
- Current Capacity : 2.2A max(24V).
- Continuous current per phase: 1.5 A.
- Minimum Logic voltage: 2.5V.
- Maximum Logic Voltage: 5V.
- Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32.
- Dimensions : 15 x 20 mm.
- Weight: 4 gm.
-
Cytron G15 Shield
₹ 892.00(inc GST)
₹ 755.93 (+18% GST extra)
-
Arduino reset button
-
4 x G15 Cube Servo ports.
-
External power port for a servo with polarity protection
-
Stackable I/O header pin
-
Selectable digital pins for the control pin with mini jumpers
-
TX and RX indicator LEDs to show communication activities, only on Rev2.0.
-
Selectable Serial pins, Either hardware serial or software serial via mini jumpers, only on Rev2.0
-
-
L293D Motor Driver Module
₹ 119.00(inc GST)
₹ 100.85 (+18% GST extra)
- The driver two holes of 3 mm dia.
- Male burg-stick connectors for supply, ground and input connection.
- Screw terminal connectors for easy motor connection.
- High noise immunity inputs.
- Operating Voltage(VDC): 4.5 to 12
- Peak Current (A): 600 mA
- No. of Channels: 1
-
Cytron SmartDriveDuo-10 MDDS10 DC MOTOR DRIVER
₹ 3,937.00(inc GST)
₹ 3336.44 (+18% GST extra)
-
Single power operation
-
Dual Channels means it can drive two brush motor independently, or mixed.
- Support Signed magnitude and Locked Anti-phase in PWM mode.
-
Two manual/test buttons for each channel.
-
Two output indicator LEDs for each channel.
-
Power, Error indicator, RUN status (Left and Right) LEDs
-
On board reset button to restart the MCU after changing operation mode.
-
Operating modes: RC (RC servo signal), Analog, PWM, simplified and packetized UART.
-
-
10A Motor Driver Shield – MD10
₹ 1,564.00(inc GST)
₹ 1325.42 (+18% GST extra)
- Bi-directional control of 1 brushed DC motor.
- Support motor voltage ranges from 7V to 25V, .
- Maximum current up to 10A continuous and 15A peak (10 seconds).
- Solid state components provide faster response time and eliminate the wear and tear of a mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
- Speed control PWM frequency up to 10KHz.
- Selectable digital pins for PWM and DIR.
-
Cytron MDS160A SmartDrive160 160AMP Dc Motor Driver (Peak 190Amp)
₹ 19,845.00(inc GST)
₹ 16817.8 (+18% GST extra)
- Bi-directional control for a single brushed DC motor.
- Support input voltage from 8V to 28V.
- Maximum current up to 190A peak (1 minute), 175A (2 minutes) or 160A (continuously).
- 16 KHz switching frequency for quiet operation.
- LiPo battery low voltage warning.
- Thermal protection.